scholarly journals Modified Nigella Sativa Seeds as a Novel Efficient Natural Adsorbent for Removal of Methylene Blue Dye

Molecules ◽  
2018 ◽  
Vol 23 (8) ◽  
pp. 1950 ◽  
Author(s):  
Souad Rakass ◽  
Ahmed Mohmoud ◽  
Hicham Oudghiri Hassani ◽  
Mostafa Abboudi ◽  
Fethi Kooli ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Removal Efficiency ◽  
Ph Value ◽  
Nigella Sativa ◽  
Blue Dye ◽  
Removal Process ◽  
Removal Capacity ◽  
Before And After ◽  
Different Temperatures ◽  
Pseudo Second Order

The aim of this work was to investigate the use of modified nigella sativa seeds (MNS) for removing of methylene blue (MB) dye from aqueous solution. The nigella sativa (NS) seeds have been pre-treated at different temperatures and periods of time. The maximum adsorption of MB was achieved using NS sample washed with distilled water pre-heated at 65 °C for one hour, then ground to 250 µm particle size (MNS-4). Different parameters were modified to optimize the removal process of MB using MNS-4, such as contact times, temperatures, initial dye concentrations, adsorbent doses, and pH of the solution. MNS-4 exhibited a removal efficiency of 99% for initial dye concentrations greater than 800 ppm at pH value of 11. The kinetic study indicated that the removal process follows the pseudo second order model. The removal was spontaneous, endothermic and favorable, and this was indicated by the thermodynamic study. Maximum removal capacity was 194 mg/g as deduced from Langmuir model. The removal efficiency was maintained after four recycle uses. The modified nigella sativa seeds were characterized before, and after adsorption and regeneration by Fourier Transform infrared (FTIR) and scanning electron microscopy (SEM). The data suggested that nigella sativa seeds could be a prospective agent for removing MB from wastewater.

scholarly journals Molybdenum Trioxide: Efficient Nanosorbent for Removal of Methylene Blue Dye from Aqueous Solutions

Molecules ◽  
2018 ◽  
Vol 23 (9) ◽  
pp. 2295 ◽  
Author(s):  
Souad Rakass ◽  
Hicham Oudghiri Hassani ◽  
Mostafa Abboudi ◽  
Fethi Kooli ◽  
Ahmed Mohmoud ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Aqueous Solutions ◽  
Removal Efficiency ◽  
Molybdenum Trioxide ◽  
Second Order ◽  
Blue Dye ◽  
Order Kinetic ◽  
Methylene Blue Dye ◽  
Removal Capacity ◽  
Pseudo Second Order

Nano Molybdenum trioxide (α-MoO3) was synthesized in an easy and efficient approach. The removal of methylene blue (MB) in aqueous solutions was studied using this material. The effects of various experimental parameters, for example contact time, pH, temperature and initial MB concentration on removal capacity were explored. The removal of MB was significantly affected by pH and temperature and higher values resulted in increase of removal capacity of MB. The removal efficiency of Methylene blue was 100% at pH = 11 for initial dye concentrations lower than 150 ppm, with a maximum removal capacity of 152 mg/g of MB as gathered from Langmuir model. By comparing the kinetic models (pseudo first-order, pseudo second-order and intraparticle diffusion model) at various conditions, it has been found that the pseudo second-order kinetic model correlates with the experimental data well. The thermodynamic study indicated that the removal was endothermic, spontaneous and favorable. The thermal regeneration studies indicated that the removal efficiency (99%) was maintained after four cycles of use. Fourier Transform Infrared (FTIR) and Scanning Electron Microscopy (SEM) confirmed the presence of the MB dye on the α-MoO3 nanoparticles after adsorption and regeneration. The α-MoO3 nanosorbent showed excellent removal efficiency before and after regeneration, suggesting that it can be used as a promising adsorbent for removing Methylene blue dye from wastewater.

Adsorption of Th4+ on Waste Beer Yeast

2013 ◽  
Vol 726-731 ◽  
pp. 2111-2114
Author(s):  
Jing Wang ◽  
Yan Chen ◽  
Bo Yang ◽  
Juan Feng ◽  
Xiao Yan Lin
Keyword(s):  
Removal Efficiency ◽  
Adsorption Kinetics ◽  
Ph Value ◽  
Order Equation ◽  
Absorption Time ◽  
Radioactive Wastewater ◽  
Before And After ◽  
Pseudo Second Order ◽  
Optimized Conditions ◽  
Beer Yeast

Waste beer yeast was utilized as adsorbent to remove Th4+ from simulated radioactive wastewater. Effects of various parameters including pH value, temperature, absorbent dosage, and absorption time on adsorption of Th4+ by waste beer yeast were studied. Beer yeast before and after adsorption was characterized by IR and SEM. The results show that the removal efficiency could be reached 95% at the optimized conditions. The adsorption kinetics was described well by the pseudo second-order equation.

scholarly journals Iron Molybdate Fe2(MoO4)3 Nanoparticles: Efficient Sorbent for Methylene Blue Dye Removal from Aqueous Solutions

Molecules ◽  
2020 ◽  
Vol 25 (21) ◽  
pp. 5100
Author(s):  
Ahmed Mohmoud ◽  
Souad Rakass ◽  
Hicham Oudghiri Hassani ◽  
Fethi Kooli ◽  
Mostafa Abboudi ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Aqueous Solutions ◽  
Removal Efficiency ◽  
Dye Removal ◽  
Blue Dye ◽  
Iron Molybdate ◽  
Thermal Regeneration ◽  
Simple Method ◽  
Removal Capacity ◽  
Adsorbent Dose

The present study investigated iron molybdate (Fe2(MoO4)3), synthesized via a simple method, as a nanosorbent for methylene blue (MB) dye removal from aqueous solutions. Investigations of the effects of several parameters like contact time, adsorbent dose, initial dye concentration, temperature and pH were carried out. The results showed that MB removal was affected, significantly, by adsorbent dose and pH. Interestingly, lower values of adsorbent dose resulted in the removal of higher amounts of MB. At the optimum pH, the removal efficiency of 99% was gained with an initial MB concentration of ≤60 ppm. The kinetic study specified an excellent correlation of the experimental results with the pseudo-second-order kinetics model. Thermodynamic studies proved a spontaneous, favorable and endothermic removal. The maximum amount of removal capacity of MB dye was 6173 mg/g, which was determined from the Langmuir model. The removal efficiency was shown to be retained after three cycles of reuse, as proven by thermal regeneration tests. The presence and adsorption of the dye onto the Fe2(MoO4)3 nanoparticle surface, as well as the regeneration of the latter, was ascertained by scanning electron microscopy (SEM) and Fourier-transform infrared spectroscopy (FTIR). These findings are indicative that the investigated nanosorbent is an excellent candidate for the removal of MB in wastewater.

Adsorption of methylene blue dye onto activated carbons based on agricultural by-products: equilibrium and kinetic studies

2013 ◽  
Vol 67 (8) ◽  
pp. 1688-1694 ◽  
Author(s):  
Z. Ioannou ◽  
J. Simitzis
Keyword(s):  
Methylene Blue ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Activated Carbons ◽  
Kinetic Studies ◽  
Blue Dye ◽  
Different Temperatures ◽  
Pseudo Second Order ◽  
Mb Adsorption

Mixtures of novolac resin and olive stone biomass (20/80 and 40/60 w/w) were cured, pyrolyzed up to 1,000 °C and activated with CO2 under a continuous flow operation (named N20B-cCa and N40B-cCa respectively). Commercial activated charcoal was similarly re-activated with CO2 and used for comparison reasons (AC-a). The characterization of these materials was performed by Fourier transform Infrared (FTIR) analysis and their specific surface area was determined according to DIN 66132. The materials were tested for their adsorption abilities at different temperatures (298, 333 K) and initial dye concentrations (0.01–0.35 g/L) using 1 L of methylene blue (MB) solution in 10 g of activated carbon. MB adsorption kinetic was also studied. The FTIR spectra of all activated carbons show absorption peaks which correspond to –OH, –CH, –C–O–C– groups and to aromatic ring. The presence of the absorption peak at about 1,400 cm−1 for N20B-cCa, N40B-cCa indicates more acidic groups on them compared to the commercial AC-a. The specific surface area of N20B-cCa, N40B-cCa and AC-a has values equal to 352, 342 and 760 m2/g respectively. From the applied kinetic models, pseudo-second-order equation could best describe MB adsorption. Consequently, such adsorbents can be used as filters to adsorb dyes from wastewaters.

scholarly journals The Removal of Methylene Blue Dye from Aqueous Solutions Using Activated and Non-Activated Bentonites

2003 ◽  
Vol 21 (5) ◽  
pp. 451-462 ◽  
Author(s):  
Sameer Al-Asheh ◽  
Fawzi Banat ◽  
Leena Abu-Aitah
Keyword(s):  
Methylene Blue ◽  
Ph Value ◽  
Sodium Dodecyl ◽  
Freundlich Isotherm ◽  
Blue Dye ◽  
Batch Adsorption ◽  
Ionic Surfactant ◽  
Methylene Blue Dye ◽  
X Ray Diffraction ◽  
Initial Ph

An improvement in the adsorption capacity of naturally available bentonite towards water pollutants such as Methylene Blue dye (MBD) is certainly needed. For this purpose, sodium bentonite was activated by two methods: (1) treatment with sodium dodecyl sulphate (SDS) as an ionic surfactant and (2) thermal treatment in an oven operated at 850°C. Batch adsorption tests were carried out on removing MBD from aqueous solution using the above-mentioned bentonites. It was found that the effectiveness of bentonites towards MBD removal was in the following order: thermal-bentonite > SDS-bentonite > natural bentonite. X-Ray diffraction analysis showed that an increase in the microscopic bentonite platelets on treatment with SDS was the reason behind the higher uptake of MBD. An increase in sorbent concentration or initial pH value of the solutions resulted in a greater removal of MBD from the solution. An increase in temperature led to an increase in MBD uptake by the bentonites studied in this work. The Freundlich isotherm model was employed and found to represent the experimental data well.

Adsorption of Methylene Blue from Aqueous Solution Using Honeycomb-Cinder

2012 ◽  
Vol 550-553 ◽  
pp. 2259-2262
Author(s):  
Song Bo Cui ◽  
Hua Yong Zhang ◽  
Lu Yi Zhang
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Ph Value ◽  
Dye Wastewater ◽  
Batch System ◽  
Adsorption Data ◽  
Adsorption Processes ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Mb Adsorption

The adsorption behavior of methylene blue (MB) dye from aqueous solutions onto honeycomb-cinder (HC) and its acid-activated product was investigated in a batch system. The results showed the adsorption capacity was decreased for raw HC samples with the increase of pH value, while it was increased for activated samples. The adsorption data were fit with Langmuir isotherm model for MB adsorption by all samples. The MB adsorption capacity on samples was increased from 2.62 mg/g to 7.81 mg/g and 7.00 mg/g after acid-activated by HCl and H2SO4, respectively. The adsorption processes of MB followed pseudo-second-order kinetics with a coefficient of correlation≥0.99. This study demonstrated that acid-activated HC has superior adsorbing ability for MB than raw HC and can be used as alternative adsorbents in dye wastewater treatment.

Removal of Methylene Blue Dye by Using Eggshell Powder

2013 ◽  
Vol 65 (1) ◽  
Author(s):  
Norzita Ngadi ◽  
Chin Chiek Ee ◽  
Nor Aida Yusoff
Keyword(s):  
Methylene Blue ◽  
Textile Industry ◽  
Low Cost ◽  
Kinetic Studies ◽  
Operating Conditions ◽  
Blue Dye ◽  
Dye Wastewater ◽  
Order Model ◽  
Aquatic Life ◽  
Pseudo Second Order

Dyes contain carcinogenic materials which can cause serious hazards to aquatic life and the users of water. Textile industry is the main source of dye wastewater which results in environmental pollution. Many studies have been conducted to investigate the use of low cost adsorbent as an alternative technique for the adsorption of dye. The objective of this study is to determine the potential of eggshell powder as an adsorbent for methylene blue removal and find out the best operating conditions for the color adsorption at laboratory scale. The adsorption of cationic methylene blue from aqueous solution onto the eggshell powder was carried out by varying the operating parameters which were contact time, pH, dosage of eggshell powder and temperature in order to study their effect in adsorption capacity of eggshell powder. The results obtained showed that the best operating condition for removal of methylene blue was at pH 10 (78.98 %) and temperature 50°C (47.37 %) by using 2 g of eggshell powder (57.03 %) with 30 minutes equilibrium time (41.36 %). The kinetic studies indicated that pseudo-second-order model best described the adsorption process.

scholarly journals Heterogeneous Fenton-Like Oxidation of Methylene Blue Using Alternative Catalysts

2021 ◽  
Vol 29 (48) ◽  
pp. 91-97
Author(s):  
Juraj Michálek ◽  
Kseniya Domnina ◽  
Veronika Kvorková ◽  
Kristína Šefčovičová ◽  
Klaudia Mončeková ◽  
...  
Keyword(s):  
Hydrogen Peroxide ◽  
Methylene Blue ◽  
Low Cost ◽  
Hydrogen Peroxide Solution ◽  
Blue Dye ◽  
Order Kinetic ◽  
Heterogeneous Fenton ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Black Nickel

Abstract The usage of the low-cost catalysts for methylene blue removal from wastewater was investigated. Heterogeneous Fenton-like process consists of the use of a hydrogen peroxide solution, and an iron-rich catalyst, red mud and black nickel mud were used for that purpose. The factors such as the catalyst dose and the hydrogen peroxide solution volume were monitored. The results of experiments showed that the degradation of methylene blue dye in Fenton-like oxidation process using selected catalysts can be described by a pseudo-second-order kinetic model. The highest dye removal efficiency (87.15 %) was achieved using the black nickel mud catalyst after 30 minutes of reaction.

Study on Adsorption Properties of Different Dyes on Montmorillonite

2012 ◽  
Vol 454 ◽  
pp. 305-309 ◽  
Author(s):  
Ping Chen ◽  
Xian Jun Lu ◽  
Jun Qiu
Keyword(s):  
Methylene Blue ◽  
Ph Value ◽  
Carbon Chain ◽  
Adsorption Properties ◽  
Organically Modified ◽  
Optimum Ph ◽  
Before And After ◽  
Higher Temperature ◽  
Adsorption Amount ◽  
Acid Blue

Using Octadecyltrimethylammonium cations with long carbon chain to modify calcium montmorillonite samples, the adsorption properties of different dyes on montmorillonite before and after modification were investigated. Results showed that the basic dye of methylene blue was easily adsorbed by natual calcium montmorillonite, while the adsorption ability for acid blue and neutral blue was greatly improved when it was organically modified, and the adsorption amount increased with the increasing of modifier dosage. The adsorption ratio was influnced by reaction time, the temperature and the solution’s pH value. It suggested that the adsorption balance time was about 60min; higher temperature was good for acid blue adsorbed on organic montmorillonite, but neutral blue’s adsorption amount was greater at the room temperature; the optimum pH was 9 for methylene blue adsorption, while low pH was better for acid blue and neutral blue adsorption.

scholarly journals Removal of Phenol from Aqueous Solution by Adsorption on to Coal Fly Ash

1996 ◽  
Vol 13 (6) ◽  
pp. 527-536 ◽  
Author(s):  
L.J. Alemany ◽  
M.C. Jiménez ◽  
M.A. Larrubia ◽  
F. Delgado ◽  
J.M. Blasco
Keyword(s):  
Aqueous Solution ◽  
Fly Ash ◽  
Removal Efficiency ◽  
Ph Value ◽  
Coal Fly Ash ◽  
Solid Wastes ◽  
Power Stations ◽  
Different Temperatures ◽  
Coal Power ◽  
Coal Power Stations

The present work examines the possible use of fly ash, a byproduct of coal power stations, as a means of removing phenol from water, or equivalently, of restricting its movement in solid wastes or soil. Equilibrium experiments were performed to evaluate the removal efficiency of fly ash. The adsorption experiments were undertaken using fly ash treated at three different pH levels and with three different temperatures. The results indicate that although phenol can be removed from water, this depends markedly on the temperature and pH value of the treatment solution employed.

Sign in / Sign up

Export Citation Format

Share Document