scholarly journals Column Leaching of Greek Low-Grade Limonitic Laterites

Minerals ◽  
2018 ◽  
Vol 8 (9) ◽  
pp. 377 ◽  
Author(s):  
Kostas Komnitsas ◽  
Evangelos Petrakis ◽  
Olga Pantelaki ◽  
Anna Kritikaki
Keyword(s):  
Leach Solution ◽  
Low Grade ◽  
Test Duration ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Column Leaching ◽  
X Ray ◽  
H2so4 Concentration ◽  
Peristaltic Pumps ◽  
Leaching Solution

In this study, column leaching experiments were carried out to investigate the extraction of Ni and Co from low-grade limonitic laterites from Agios Ioannis mines in central Greece. Tests were carried out in laboratory Plexiglas columns using H2SO4 as leaching solution. Parameters determining the efficiency of the process, i.e., acid concentration (0.5 M or 1.5 M) and addition of 20 or 30 g/L of sodium sulfite (Na2SO3) in the leaching solution, were also studied. Upflow transport of the leaching solution with the use of peristaltic pumps was carried out, while the pregnant leach solution (PLS) was recycled several times over the entire test duration. The concentration of Ni, Co, Fe, Ca, Al, Mg, and Mn in the PLS was determined by Atomic Absorption Spectroscopy (AAS). The ore and the leaching residues were characterized by different techniques, i.e., X-ray fluorescence (XRF), X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, and differential scanning calorimetry and thermogravimetry (DSC/TG). The experimental results showed that (i) Ni and Co extractions increased with the increase of H2SO4 concentration—60.2% Ni and 59.0% Co extractions were obtained after 33 days of leaching with 1.5 M H2SO4; (ii) addition of 20 g/L Na2SO3 in the leaching solution resulted in higher extraction percentages for both metals (73.5% for Ni and 84.1% for Co, respectively), whereas further increase of Na2SO3 concentration to 30 g/L only marginally affected Ni and Co extractions; and (iii) when leaching was carried out with 1.5 M H2SO4 and 20 g/L Na2SO3, its selectivity was improved, as deduced from the ratios Ni/Mg, Ni/Ca and Ni/Al in the PLS; on the other hand, the ratio Ni/Fe dropped as a result of the higher Fe extraction compared with that of Ni.

scholarly journals Extraction of Boron from Ludwigite Ore: Mechanism of Soda-Ash Roasting of Lizardite and Szaibelyite

Minerals ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 533 ◽  
Author(s):  
Xin Zhang ◽  
Guanghui Li ◽  
Jinxiang You ◽  
Jian Wang ◽  
Jun Luo ◽  
...  
Keyword(s):  
Sodium Carbonate ◽  
Energy Dispersive Spectrometer ◽  
Low Grade ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Selective Activation ◽  
X Ray ◽  
Shed Light ◽  
Soda Ash ◽  
Scanning Electron

Ludwigite ore is a typical low-grade boron ore accounting for 58.5% boron resource of China, which is mainly composed of magnetite, lizardite and szaibelyite. During soda-ash roasting of ludwigite ore, the presence of lizardite hinders the selective activation of boron. In this work, lizardite and szaibelyite were prepared and their soda-ash roasting behaviors were investigated using thermogravimetric-differential scanning calorimetry (TG-DSC), X-ray diffraction (XRD), and scanning electron microscope and energy dispersive spectrometer (SEM-EDS) analyses, in order to shed light on the soda-ash activation of boron within ludwigite ore. Thermodynamics of Na2CO3-MgSiO3-Mg2SiO4-Mg2B2O5 via FactSage show that the formation of Na2MgSiO4 was preferential for the reaction between Na2CO3 and MgSiO3/Mg2SiO4. While, regarding the reaction between Na2CO3 and Mg2B2O5, the formation of NaBO2 was foremost. Raising temperature was beneficial for the soda-ash roasting of lizardite and szaibelyite. At a temperature lower than the melting of sodium carbonate (851 °C), the soda-ash roasting of szaibelyite was faster than that of lizardite. Moreover, the melting of sodium carbonate accelerated the reaction between lizardite with sodium carbonate.

Studies on the Preparation, Characterization and Solubility of -Cyclodextrin-Roxythromycin Inclusion Complexes

2009 ◽  
Vol 2 (2) ◽  
pp. 523-530
Author(s):  
D. Nagasamy Venkatesh ◽  
S. Karthick ◽  
M. Umesh ◽  
G. Vivek ◽  
R.M. Valliappan ◽  
...  
Keyword(s):  
Dissolution Rate ◽  
Inclusion Complexes ◽  
Phase Solubility ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Ir Studies ◽  
Poorly Soluble ◽  
Poorly Soluble Drug

Roxythromycin/ β-cyclodextrin (Roxy/ β-CD) dispersions were prepared with a view to study the influence of β-CD on the solubility and dissolution rate of this poorly soluble drug. Phase-solubility profile indicated that the solubility of roxythromycin was significantly increased in the presence of β-cyclodextrin and was classified as AL-type, indicating the 1:1 stoichiometric inclusion complexes. Physical characterization of the prepared systems was carried out by differential scanning calorimetry (DSC), X-ray diffraction studies (XRD) and IR studies. Solid state characterization of the drug β-CD binary system using XRD, FTIR and DSC revealed distinct loss of drug crystallinity in the formulation, ostensibly accounting for enhancement of dissolution rate.

scholarly journals A review of nanotechnology with an emphasis on Nanoplex

2015 ◽  
Vol 51 (2) ◽  
pp. 255-263
Author(s):  
Rupali Nanasaheb Kadam ◽  
Raosaheb Sopanrao Shendge ◽  
Vishal Vijay Pande
Keyword(s):  
Drug Delivery ◽  
Drug Delivery Systems ◽  
Drug Loading ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Conventional Drug ◽  
Anionic Drugs ◽  
Oppositely Charged ◽  
The Brain

<p>The use of nanotechnology based on the development and fabrication of nanostructures is one approach that has been employed to overcome the challenges involved with conventional drug delivery systems. Formulating Nanoplex is the new trend in nanotechnology. A nanoplex is a complex formed by a drug nanoparticle with an oppositely charged polyelectrolyte. Both cationic and anionic drugs form complexes with oppositely charged polyelectrolytes. Compared with other nanostructures, the yield of Nanoplex is greater and the complexation efficiency is better. Nanoplex are also easier to prepare. Nanoplex formulation is characterized through the production yield, complexation efficiency, drug loading, particle size and zeta potential using scanning electron microscopy, differential scanning calorimetry, X-ray diffraction and dialysis studies. Nanoplex have wide-ranging applications in different fields such as cancer therapy, gene drug delivery, drug delivery to the brain and protein and peptide drug delivery.</p>

scholarly journals Diethylstilbestrol Modifies the Structure of Model Membranes and Is Localized Close to the First Carbons of the Fatty Acyl Chains

Biomolecules ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 220
Author(s):  
Alessio Ausili ◽  
Inés Rodríguez-González ◽  
Alejandro Torrecillas ◽  
José A. Teruel ◽  
Juan C. Gómez-Fernández
Keyword(s):  
Membrane Surface ◽  
Water Layer ◽  
Fatty Acyl ◽  
31P Nmr Spectroscopy ◽  
Relaxation Rates ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Acyl Chains ◽  
Dynamics Simulations

The synthetic estrogen diethylstilbestrol (DES) is used to treat metastatic carcinomas and prostate cancer. We studied its interaction with membranes and its localization to understand its mechanism of action and side-effects. We used differential scanning calorimetry (DSC) showing that DES fluidized the membrane and has poor solubility in DMPC (1,2-dimyristoyl-sn-glycero-3-phosphocholine) in the fluid state. Using small-angle X-ray diffraction (SAXD), it was observed that DES increased the thickness of the water layer between phospholipid membranes, indicating effects on the membrane surface. DSC, X-ray diffraction, and 31P-NMR spectroscopy were used to study the effect of DES on the Lα-to-HII phase transition, and it was observed that negative curvature of the membrane is promoted by DES, and this effect may be significant to understand its action on membrane enzymes. Using the 1H-NOESY-NMR-MAS technique, cross-relaxation rates for different protons of DES with POPC (1-palmitoyl-2-oleoyl-sn-glycero-3-phosphocholine) protons were calculated, suggesting that the most likely location of DES in the membrane is with the main axis parallel to the surface and close to the first carbons of the fatty acyl chains of POPC. Molecular dynamics simulations were in close agreements with the experimental results regarding the location of DES in phospholipids bilayers.

scholarly journals Effects of Sintering Temperature on Densification, Microstructure and Mechanical Properties of Al-Based Alloy by High-Velocity Compaction

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 218
Author(s):  
Xianjie Yuan ◽  
Xuanhui Qu ◽  
Haiqing Yin ◽  
Zaiqiang Feng ◽  
Mingqi Tang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Velocity ◽  
Sintered Density ◽  
Sintering Temperature ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
High Velocity Compaction ◽  
Sintered Temperature

This present work investigates the effects of sintering temperature on densification, mechanical properties and microstructure of Al-based alloy pressed by high-velocity compaction. The green samples were heated under the flow of high pure (99.99 wt%) N2. The heating rate was 4 °C/min before 315 °C. For reducing the residual stress, the samples were isothermally held for one h. Then, the specimens were respectively heated at the rate of 10 °C/min to the temperature between 540 °C and 700 °C, held for one h, and then furnace-cooled to the room temperature. Results indicate that when the sintered temperature was 640 °C, both the sintered density and mechanical properties was optimum. Differential Scanning Calorimetry, X-ray diffraction of sintered samples, Scanning Electron Microscopy, Energy Dispersive Spectroscopy, and Transmission Electron Microscope were used to analyse the microstructure and phases.

Characterization and A Preliminary Study of TiO2 Synthesis from Lampung Iron Sand

2020 ◽  
Vol 849 ◽  
pp. 113-118
Author(s):  
Yayat Iman Supriyatna ◽  
Slamet Sumardi ◽  
Widi Astuti ◽  
Athessia N. Nainggolan ◽  
Ajeng W. Ismail ◽  
...  
Keyword(s):  
Food Packaging ◽  
Xrd Analysis ◽  
Major Elements ◽  
Raw Material ◽  
Solid Residue ◽  
X Ray Diffraction ◽  
X Ray ◽  
Leaching Solution ◽  
Ti Content

The purpose of this study is to characterize Lampung iron sand and to conduct preliminary experiments on the TiO2 synthesis which can be used for the manufacturing of functional food packaging. The iron sand from South Lampung Regency, Lampung Province that will be utilized as raw material. The experiment was initiated by sieving the iron sand on 80, 100, 150, 200 and 325 mesh sieves. Analysis using X-Ray Fluorescence (XRF) to determine the element content and X-Ray Diffraction (XRD) to observe the mineralization of the iron sand was conducted. The experiment was carried out through the stages of leaching, precipitation, and calcination. Roasting was applied firstly by putting the iron sand into the muffle furnace for 5 hours at a temperature of 700°C. Followed by leaching using HCl for 48 hours and heated at 105°C with a stirring speed of 300 rpm. The leaching solution was filtered with filtrate and solid residue as products. The solid residue was then leached using 10% H2O2 solution. The leached filtrate was heated at 105°C for 40 minutes resulting TiO2 precipitates (powder). Further, the powder was calcined and characterized. Characterization of raw material using XRF shows the major elements of Fe, Ti, Mg, Si, Al and Ca. The highest Ti content is found in mesh 200 with 9.6%, while iron content is about 80.7%. While from the XRD analysis, it shows five mineral types namely magnetite (Fe3O4), Rhodonite (Mn, Fe, Mg, Ca) SiO3, Quart (SiO2), Ilmenite (FeOTiO2) and Rutile (TiO2). The preliminary experiment showed that the Ti content in the synthesized TiO2 powder is 21.2%. The purity of TiO2 is low due to the presence of Fe metal which is dissolved during leaching, so that prior to precipitation purification is needed to remove impurities such as iron and other metals.

Study of Low-Grade Nickel Laterite Processing Using Palm Shell Charcoal as Reductant

2020 ◽  
Vol 1000 ◽  
pp. 436-446
Author(s):  
Bambang Suharno ◽  
Nolzha Primadha Ilman ◽  
Achmad Shofi ◽  
Deni Ferdian ◽  
Fajar Nurjaman
Keyword(s):  
Sodium Sulfate ◽  
Selective Reduction ◽  
Reduction Process ◽  
Low Grade ◽  
X Ray Diffraction ◽  
X Ray ◽  
Palm Shell ◽  
Higher Temperature ◽  
Nickel Grade

This study was conducted to investigate the effect of palm shell charcoal reductant in the selective reduction of nickel ore with the addition of additive at various temperatures and times. In this present work, 10 wt. % of sodium sulfate as additive and 5, 10, 15 wt. % of palm shell charcoal as reductants were used. The reduction of nickel ore was performed at 950oC, 1050oC, and 1150oC for 60, 90, and 120 minutes. A wet magnetic separation method was then carried out to separate the concentrates and tailings. Characterization of reduced ore was performed by X-Ray Diffraction (XRD) and Scanning Electron Microscope (SEM) with Energy Dispersive X-ray Spectroscopy (EDS), while the composition of ferronickel in concentrate was identified by X-Ray Fluorescence (XRF). The result showed that the higher temperature reduction, the higher of nickel grade, and its recovery at the concentrate. Nevertheless, the longer reduction time and the more reductant in nickel ore lowering the nickel grade and its recovery in the concentrate. The optimum condition in this selective reduction process was obtained with the addition of 5 wt. % of reductant and 10 wt. % of sodium sulfate in nickel ore, which was reduced at 1150oC for 60 minutes. It resulted in 4.60% and 73.23% for nickel grade and its recovery, respectively.

scholarly journals Mechanochemical treatment of Serbian kaolin clay to obtain high reactive pozzolana

2013 ◽  
Vol 78 (4) ◽  
pp. 579-590 ◽  
Author(s):  
Aleksandra Mitrovic ◽  
Miodrag Zdujic
Keyword(s):  
Hardened Steel ◽  
Pozzolanic Activity ◽  
Mechanochemical Treatment ◽  
Kaolin Clay ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Milling Parameters ◽  
Milling Medium ◽  
The Given

Mechanochemical treatment of Serbian kaolin clay was carried out in a planetary ball mill using two different milling media, hardened steel or zirconia vials and balls. The samples obtained with various milling times were characterized by the particle size laser diffraction (PSLD), X-ray diffraction (XRD), differential scanning calorimetry/thermogravimetry (DTA/TGA) and Fourier-transform infrared (FTIR) analyses. Mechanochemical treatment induced amorphization of the kaolinite phase accompanied by dehydroxylation. It was found that for the given milling parameters, amorphization mainly took place in the milling period up to 15 min, and was completed after about 30 min of milling for both milling media used. The pozzolanic activities were determined by the Chapelle method. Milling in the hardened steel milling medium had no significant influence on pozzolanic activity, even though there was accumulated iron contamination. For both milling media, pozzolanic activity of 0.79 was obtained for the samples milled for 15 min and it remained almost unchanged with prolonged milling. The determined pozzolanic activity values are close to these of commercial metakaolinite or metakaolinite obtained by the calcination of the same clay, therefore, indicating possibility for obtaining high reactive pozzolana by mechanochemical treatment of Serbian kaoline clay.

Liquid crystalline polyureas with oligo(ethylene glycol) sequences

e-Polymers ◽  
2010 ◽  
Vol 10 (1) ◽  
Author(s):  
Shahram Mehdipour-Ataei ◽  
Leila Akbarian-Feizi
Keyword(s):  
Liquid Crystalline ◽  
Spectroscopic Method ◽  
Polymerization Reaction ◽  
X Ray Diffraction ◽  
Subsequent Reaction ◽  
Scanning Calorimetry ◽  
Polar Solvents ◽  
X Ray ◽  
H Nmr ◽  
Ft Ir

AbstractA diamine monomer containing ester, amide and ether functional groups was prepared and its polymerization reaction with different diisocyanates to give main chain poly(ester amide ether urea)s was investigated. The monomer was synthesized via reaction of terephthaloyl chloride with 4-hydroxybenzoic acid and subsequent reaction of the resulted diacid with 1,8-diamino-3,6-dioxaoctane. The polymers were characterized by FT-IR and 1H-NMR spectroscopic method and elemental analysis. The resulting polymers exhibited excellent solubility in polar solvents. Crystallinity of the resulted polymers was evaluated by wide-angle X-ray diffraction (WXRD) method, and they exhibited semi-crystalline patterns. The glass transition temperatures (Tg) of the polymers determined by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA) were in the range of 88-112 °C. The temperatures for 10% weight loss (T10) from their thermogravimetric analysis (TGA) curves were found to be in the range of 297-312 °C in air. Also the prepared polyureas showed liquid crystalline character.

Sign in / Sign up

Export Citation Format

Share Document