scholarly journals The Effect of Mineral-Based Mixtures Containing Coal Fly Ash and Sewage Sludge on Chlorophyll Fluorescence and Selected Morphological Parameters of Deciduous and Coniferous Trees

Minerals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 778
Author(s):  
Agnieszka Bęś ◽  
Łukasz Sikorski ◽  
Krzysztof Szreder
Keyword(s):  
Fly Ash ◽  
Sewage Sludge ◽  
Ponderosa Pine ◽  
Power Plants ◽  
High Salinity ◽  
Coal Fly Ash ◽  
Coal Ash ◽  
Morphological Parameters ◽  
Optimal Conditions ◽  
Mineral Mixtures

Coal fly ash (CFA), which is generated in huge quantities in coal-fired power plants, is a problem worldwide. Mixtures with ash and sewage sludge alter morphological and biochemical characteristics of plants. In this experiment, the response of pine, spruce, beech and alder growing for four years to mineral mixtures based on coal fly ash and high salinity sewage sludge (SS) was studied. The four-year experiment determined the chlorophyll a fluorescence of the tested plants, their height and yield, the salinity level of the tested mixtures and their phytotoxicity. Mixtures of coal ash with sewage sludge proved to be more beneficial to plants than their separate application. After four years, among the studied species, the highest increase in height and biomass was recorded for European alder and Scots pine. These species were also characterized by high photosynthetic indices. Mixtures containing 29% SS created optimal conditions for the development of the studied tree species. Grey alder and ponderosa pine can be recommended for reclamation of degraded areas where CFA and SS mixtures are used.

scholarly journals Coal Fly Ash Ceramics: Preparation, Characterization, and Use in the Hydrolysis of Sucrose

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Ricardo Pires dos Santos ◽  
Jorge Martins ◽  
Carlos Gadelha ◽  
Benildo Cavada ◽  
Alessandro Victor Albertini ◽  
...  
Keyword(s):  
Fly Ash ◽  
Surface Area ◽  
Power Plants ◽  
Coal Fly Ash ◽  
Thermal Power ◽  
Coal Ash ◽  
Mineralogical Composition ◽  
Degree Of Hydrolysis ◽  
High Degree ◽  
Hydrolysis Of

Coal ash is a byproduct of mineral coal combustion in thermal power plants. This residue is responsible for many environmental problems because it pollutes soil, water, and air. Thus, it is important to find ways to reuse it. In this study, coal fly ash, obtained from the Presidente Médici Thermal Power Plant, was utilized in the preparation of ceramic supports for the immobilization of the enzyme invertase and subsequent hydrolysis of sucrose. Coal fly ash supports were prepared at several compaction pressures (63.66–318.30 MPa) and sintered at 1200°C for 4 h. Mineralogical composition (by X-ray diffraction) and surface area were studied. The ceramic prepared with 318.30 MPa presented the highest surface area (35 m2/g) and amount of immobilized enzyme per g of support (76.6 mg/g). In assays involving sucrose inversion, it showed a high degree of hydrolysis (around 81%) even after nine reuses and 30 days’ storage. Therefore, coal fly ash ceramics were demonstrated to be a promising biotechnological alternative as an immobilization support for the hydrolysis of sucrose.

scholarly journals CONVERSION OF COAL FLY ASH TO ZEOLITE-BASED IRON OXIDE MAGNETIC NANOCOPOSITES BY MODIFIED FUSION-HYDROTHERMAL SYNTHESIS

2020 ◽  
pp. 30-35
Author(s):  
Silviya Boycheva ◽  
Denitza Zgureva
Keyword(s):  
Magnetic Properties ◽  
Iron Oxide ◽  
Fly Ash ◽  
Power Plants ◽  
Coal Fly Ash ◽  
Thermal Power ◽  
Coal Ash ◽  
Low Temperature Processing ◽  
Oxide Phases ◽  
Stage Synthesis

Coal fly ash generated in Thermal Power Plants is utilized for synthesis of zeolites due to its aluminosilicate composition. The highest degree of zeolitization of coal ash in a particular zeolite phase is achieved by double-stage synthesis involving successive alkaline melting and hydrothermal activation of the reaction mixtures, while the uniform distribution of the iron oxides transferred from the raw coal ash is ensured by ultrasonic treatment. However, the applied melting step results in the oxidation of the magnetic iron oxide phases to non-magnetic ones, which results in the loss of magnetic properties of the resulting materials. The present investigation focuses on an improved double- stage synthesis procedure by the addition of raw coal ash containing magnetite between high temperature and low temperature processing. In this way, the magnetic phase is retained in the final product and the magnetic properties of the zeolites are preserved, which is important for their application in the adsorption of pollutants from wastewater.

Zinc Oxide Recovery from Solid Waste of Electric Arc Furnace Dust (EAFD) Using Hydrometallurgical Method

2020 ◽  
Vol 849 ◽  
pp. 108-112
Author(s):  
Widi Astuti ◽  
Agus Haerudin ◽  
Istihanah Nurul Eskani ◽  
Fajar Nurjaman ◽  
Aulia Pertiwi Tri Yuda ◽  
...  
Keyword(s):  
Fly Ash ◽  
Enrichment Factor ◽  
Power Plants ◽  
Coal Fly Ash ◽  
Bottom Ash ◽  
Coal Ash ◽  
Atomic Emission ◽  
Xrd Analysis ◽  
Unburned Carbon ◽  
Amorphous Glass

Indonesia coal ash is predicted to reach 10.8 million tons in the year 2020 but its utilization is still limited. In the last decade, coal ash has become a promising REY source candidate. To determine the potency of REY in Indonesia coal ash, information about element concentration and mineralogy of the ash is essential. In this study, coal ash samples were taken from Paiton-2, Pacitan, Rembang, and Tanjung Jati coal-fired power plants. Element content and mineralogy were analyzed using Inductive Couple Plasma Mass Spectroscopy/Atomic Emission Spectroscopy (ICP-MS/AES), X-Ray Diffractometer (XRD) and petrographic. The results showed that coal fly ash and bottom ash contains critical REY in the range of 38% to 41% with Coutlook larger than one. XRD analysis showed that both fly ash and bottom ash have similar mineral phases with slightly different concentrations. The mineral phase is dominated by amorphous glass, quartz, Fe-bearing minerals, and unburned carbon. The amorphous glass phase in fly ash is in the range of 23 to 34% while in bottom ash between 14 and 34%. Unburned carbon content in fly ash and bottom ashes are 7-13% and 7-19%, respectively. Fe-bearing mineral content in fly ash is 15-20% and bottom ash is 13-20%. In addition, Indonesia coal ash has a higher Heavy-REY enrichment factor than Light-REY. The Enrichment Factor of HREY in fly ash is as much as 1.3 times (in average) of the bottom ash.

scholarly journals Processing of high-grade zeolite nanocomposites from solid fuel combustion by-products as critical raw materials substitutes

2020 ◽  
Vol 7 ◽  
pp. 22
Author(s):  
Silviya Boycheva ◽  
Denitza Zgureva ◽  
Hristina Lazarova ◽  
Katerina Lazarova ◽  
Cyril Popov ◽  
...  
Keyword(s):  
Fly Ash ◽  
Power Plants ◽  
Raw Materials ◽  
Coal Fly Ash ◽  
Thermal Power ◽  
Coal Ash ◽  
High Grade ◽  
Fly Ash Zeolite ◽  
By Products ◽  
Critical Raw Materials

High-grade zeolite nanocomposites are synthesized utilizing solid by-products from combustion of coal for energy production in Thermal Power Plants applying alkaline aging, hydrothermal and fusion-hydrothermal activation procedures. The obtained coal ash zeolites were studied with respect to their chemical and phase composition, morphology, surface parameters and thermal properties. It was found that they are distinguished in nanocrystalline morphology and significant content of iron oxide nanoparticles (γ-Fe2O3, α-Fe2O3, γ-Fe3O4) and doping elements (Cu, Co, Mn, V, W, etc.) transferred from the raw coal ash, and therefore they are assumed as nanocomposites. Coal fly ash zeolite nanocomposites are characterized by a mixed micro-mesoporous texture, significant concentration of acidic Brønsted centers due to their high surface insaturation, high chemical and thermal stabilty. This unique combination of compositional and textural properties predetermines the application of these materials as catalysts for thermal oxidation processes, anticorrosion barrier coatings, carbon capture adsorbents, matrices for hosting functional groups, detergents etc. Examples for coal fly ash zeolite applications for substitution of critical raw materials in practice are provided.

Potency of Rare Earth Elements and Yttrium in Indonesia Coal Ash

2020 ◽  
Vol 849 ◽  
pp. 102-107
Author(s):  
Widya Rosita ◽  
Dea Anisa Ayu Besari ◽  
I Made Bendiyasa ◽  
Indra Perdana ◽  
Ferian Anggara ◽  
...  
Keyword(s):  
Fly Ash ◽  
Enrichment Factor ◽  
Power Plants ◽  
Coal Fly Ash ◽  
Bottom Ash ◽  
Coal Ash ◽  
Atomic Emission ◽  
Xrd Analysis ◽  
Unburned Carbon ◽  
Amorphous Glass

Indonesia coal ash is predicted to reach 10.8 million tons in the year 2020 but its utilization is still limited. In the last decade, coal ash has become a promising REY source candidate. To determine the potency of REY in Indonesia coal ash, information about element concentration and mineralogy of the ash is essential. In this study, coal ash samples were taken from Paiton-2, Pacitan, Rembang, and Tanjung Jati coal-fired power plants. Element content and mineralogy were analyzed using Inductive Couple Plasma Mass Spectroscopy/Atomic Emission Spectroscopy (ICP-MS/AES), X-Ray Diffractometer (XRD) and petrographic. The results showed that coal fly ash and bottom ash contains critical REY in the range of 38% to 41% with Coutlook larger than one. XRD analysis showed that both fly ash and bottom ash have similar mineral phases with slightly different concentrations. The mineral phase is dominated by amorphous glass, quartz, Fe-bearing minerals, and unburned carbon. The amorphous glass phase in fly ash is in the range of 23 to 34% while in bottom ash between 14 and 34%. Unburned carbon content in fly ash and bottom ashes are 7-13% and 7-19%, respectively. Fe-bearing mineral content in fly ash is 15-20% and bottom ash is 13-20%. In addition, Indonesia coal ash has a higher Heavy-REY enrichment factor than Light-REY. The Enrichment Factor of HREY in fly ash is as much as 1.3 times (in average) of the bottom ash.

Radiochemical Techniques Applied to Laboratory Studies of Water Leaching of Heavy Metals from Coal Fly Ash

1983 ◽  
Vol 15 (11) ◽  
pp. 25-47 ◽  
Author(s):  
L Goetz
Keyword(s):  
Heavy Metals ◽  
Fly Ash ◽  
Power Plants ◽  
Coal Fly Ash ◽  
Water System ◽  
Coal Ash ◽  
Distribution Coefficients ◽  
Water Leaching ◽  
Nuclear Techniques ◽  
Pulverized Fuel

Assessment of the potential environmental impact of heavy metals (HM) mobilized by coal-fired power plants showed that water leaching of HM from pulverized fuel ash may for certain HM constitute an important pathway to the aquatic environment. This process was therefore investigated in more detail by laboratory experiments. Batch experiments were performed in order to simulate ash pond conditions, whereas column experiments were carried out to represent water leaching from fly ash deposits. Using highly sensitive radiochemical techniques such as radioactive tracers and neutron activation of fly ash the fate of a single HM could be easily followed even in very low concentration experiments. Employing radioisotopic tracers the distribution coefficients of simple ionic forms of As, Sb, Bi, Se, Te, Cr, Mo, W, Ni, Cd in a coal fly ash/water system could be determined as a function of pH. Results obtained on the adsorption and desorption behaviour of HM on coal fly ash can be explained in part on the basis of the surface predominance and the aqueous chemistry of single ionic, mainly anionic, forms of the relative elements. But ion exchange and coprecipitation phenomena also seem to be important processes. The nature and concentration of ions contained originally in the water used (distilled water, fly ash leachate and seawater) were found to have a strong influence on the sorptive behaviour of HM on coal ashes. The high degree of applicability of radiochemical and nuclear techniques to coal ash water leaching problems has been demonstrated and further points for subsequent research in this field possibly using nuclear techniques are indicated.

UTILIZATION OF COAL FLY ASH FROM POWER PLANTS - I. ASH CHARACTERIZATION

2008 ◽  
Vol 7 (3) ◽  
pp. 289-293 ◽  
Author(s):  
Maria Harja ◽  
Marinela Barbuta ◽  
Lacramioara Rusu ◽  
Nicolae Apostolescu
Keyword(s):  
Fly Ash ◽  
Power Plants ◽  
Coal Fly Ash

scholarly journals Preparation of Synthetic Zeolites from Coal Fly Ash by Hydrothermal Synthesis

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1267
Author(s):  
David Längauer ◽  
Vladimír Čablík ◽  
Slavomír Hredzák ◽  
Anton Zubrik ◽  
Marek Matik ◽  
...  
Keyword(s):  
Fly Ash ◽  
Coal Combustion ◽  
Power Plants ◽  
Coal Fly Ash ◽  
Thermal Power ◽  
Product Analysis ◽  
Coal Combustion Products ◽  
X Ray ◽  
Wide Range ◽  
Silica Alumina

Large amounts of coal combustion products (as solid products of thermal power plants) with different chemical and physical properties cause serious environmental problems. Even though coal fly ash is a coal combustion product, it has a wide range of applications (e.g., in construction, metallurgy, chemical production, reclamation etc.). One of its potential uses is in zeolitization to obtain a higher added value of the product. The aim of this paper is to produce a material with sufficient textural properties used, for example, for environmental purposes (an adsorbent) and/or storage material. In practice, the coal fly ash (No. 1 and No. 2) from Czech power plants was firstly characterized in detail (X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX), particle size measurement, and textural analysis), and then it was hydrothermally treated to synthetize zeolites. Different concentrations of NaOH, LiCl, Al2O3, and aqueous glass; different temperature effects (90–120 °C); and different process lengths (6–48 h) were studied. Furthermore, most of the experiments were supplemented with a crystallization phase that was run for 16 h at 50 °C. After qualitative product analysis (SEM-EDX, XRD, and textural analytics), quantitative XRD evaluation with an internal standard was used for zeolitization process evaluation. Sodalite (SOD), phillipsite (PHI), chabazite (CHA), faujasite-Na (FAU-Na), and faujasite-Ca (FAU-Ca) were obtained as the zeolite phases. The content of these zeolite phases ranged from 2.09 to 43.79%. The best conditions for the zeolite phase formation were as follows: 4 M NaOH, 4 mL 10% LiCl, liquid/solid ratio of 30:1, silica/alumina ratio change from 2:1 to 1:1, temperature of 120 °C, process time of 24 h, and a crystallization phase for 16 h at 50 °C.

scholarly journals Reactivity of Ground Coal Bottom Ash to Be Used in Portland Cement

J ◽  
2021 ◽  
Vol 4 (3) ◽  
pp. 223-232
Author(s):  
Esperanza Menéndez ◽  
Cristina Argiz ◽  
Miguel Ángel Sanjuán
Keyword(s):  
Fly Ash ◽  
Coal Fly Ash ◽  
Bottom Ash ◽  
Blended Cement ◽  
Coal Ash ◽  
Pozzolanic Reaction ◽  
Natural Sand ◽  
Coal Bottom Ash ◽  
Novel Material ◽  
Pozzolanic Properties

Ground coal bottom ash is considered a novel material when used in common cement production as a blended cement. This new application must be evaluated by means of the study of its pozzolanic properties. Coal bottom ash, in some countries, is being used as a replacement for natural sand, but in some others, it is disposed of in a landfill, leading thus to environmental problems. The pozzolanic properties of ground coal bottom ash and coal fly ash cements were investigated in order to assess their pozzolanic performance. Proportions of coal fly ash and ground coal bottom ash in the mixes were 100:0, 90:10, 80:20, 50:50, 0:100. Next, multicomponent cements were formulated using 10%, 25% or 35% of ashes. In general, the pozzolanic performance of the ground coal bottom ash is quite similar to that of the coal fly ash. As expected, the pozzolanic reaction of both of them proceeds slowly at early ages, but the reaction rate increases over time. Ground coal bottom ash is a promising novel material with pozzolanic properties which are comparable to that of coal fly ashes. Then, coal bottom ash subjected to an adequate mechanical grinding is suitable to be used to produce common coal-ash cements.

Characterization of Coal Fly Ash, Bottom Ash and their Possibilities as Catalysts for Biodiesel Production

2021 ◽  
Vol 904 ◽  
pp. 413-418
Author(s):  
Wilasinee Kingkam ◽  
Sasikarn Nuchdang ◽  
Dussadee Rattanaphra
Keyword(s):  
Fly Ash ◽  
Palm Oil ◽  
Power Plants ◽  
Coal Fly Ash ◽  
Bottom Ash ◽  
Biodiesel Production ◽  
Catalyst Loading ◽  
Free Lime ◽  
Operation Conditions ◽  
Class C

Coal fly ash (CFA) and bottom ash (BA) obtained from coal fired power plants in Thailand and local supplier were characterized using XRF, XRD and N2 adsorption-desorption techniques. Their possibilities for conversion of palm oil into biodiesel were investigated. Selected CFA was also modified with lanthanum (La) at different La loading and the influence of La loading on biodiesel conversion was evaluated. The resulted showed that the Class C CFA as contained large amount of CaO (free lime) could catalyze the transesterification to achieve the highest FAME content of 89% under the operation conditions; the reaction temperature of 200 °C, the reaction pressure of 39 bars, the catalyst loading of 5 wt% of oil, the molar of oil to methanol of 1:30 and the stirring speed of 600 rpm for 5 h. The addition of La on the Class C CFA had a negative effect on conversion of palm oil. The FAME content decreased gradually from 89 to 62% with increasing La loading from 0 to 1 wt%.

Sign in / Sign up

Export Citation Format

Share Document