scholarly journals Thermally Assisted Grinding of Cassiterite Associated with Pollimetallic Ore: A Comparison between Microwave and Conventional Furnaces

Minerals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 768
Author(s):  
Chunlin He ◽  
Jian Zhao ◽  
Xiujuan Su ◽  
Shaojian Ma ◽  
Toyohisa Fujita ◽  
...  
Keyword(s):  
Microwave Heating ◽  
Microwave Absorption ◽  
Size Range ◽  
Conventional Heating ◽  
Microwave Pretreatment ◽  
Selective Heating ◽  
Sulfide Ore ◽  
Heating Treatment ◽  
Fine Size

We investigated the influence of microwave and conventional heating pretreatments on the grinding of cassiterite associated with pollimetallic ore. The minerals that exhibited a stronger microwave absorption ability crushed first, which is the main difference between the microwave and the traditional heating pretreatments. The distribution of Fe, Pb, Zn, and Sn increased in the fine size range (−0.425 mm). The Fe and Pb grades in the size ranges of −3.2 + 2 mm and −2 + 1 mm after the microwave pretreatment (6 kW, 1 min) were lower than those of the traditional heating (12 kW, 400 °C, 20 min), indicating that the microwave selective heating was beneficial for pyrite and jamesonite. The grade and distribution of Sn decreased significantly in the size ranges of −3.2 + 2 mm and −2 + 1 mm and increased in the size ranges of −0.425 + 0.15 mm and −0.15 + 0.074 mm. Microwave heating treatment promoted the grinding of sulfide ore and reduced the cassiterite overgrinding.

Densification of MnDoped Tin Oxide Films by Conventional Heating and Microwave Heating Treatment

2005 ◽  
pp. 291 ◽  
Author(s):  
A. P. Rizzato ◽  
C. V. Santilli ◽  
S. H. Pulcinelli ◽  
D. Stuerga ◽  
D. Chaumont ◽  
...  
Keyword(s):  
Microwave Heating ◽  
Tin Oxide ◽  
Oxide Films ◽  
Conventional Heating ◽  
Heating Treatment ◽  
Tin Oxide Films

scholarly journals Microwaves and Heterogeneous Catalysis: A Review on Selected Catalytic Processes

Catalysts ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 246 ◽  
Author(s):  
Vincenzo Palma ◽  
Daniela Barba ◽  
Marta Cortese ◽  
Marco Martino ◽  
Simona Renda ◽  
...  
Keyword(s):  
Heterogeneous Catalysis ◽  
Energy Saving ◽  
Microwave Heating ◽  
Microwave Radiation ◽  
Heterogeneous Catalysts ◽  
Conventional Heating ◽  
Specific Effects ◽  
Natural Choice ◽  
Future Challenges ◽  
Catalyzed Reactions

Since the late 1980s, the scientific community has been attracted to microwave energy as an alternative method of heating, due to the advantages that this technology offers over conventional heating technologies. In fact, differently from these, the microwave heating mechanism is a volumetric process in which heat is generated within the material itself, and, consequently, it can be very rapid and selective. In this way, the microwave-susceptible material can absorb the energy embodied in the microwaves. Application of the microwave heating technique to a chemical process can lead to both a reduction in processing time as well as an increase in the production rate, which is obtained by enhancing the chemical reactions and results in energy saving. The synthesis and sintering of materials by means of microwave radiation has been used for more than 20 years, while, future challenges will be, among others, the development of processes that achieve lower greenhouse gas (e.g., CO2) emissions and discover novel energy-saving catalyzed reactions. A natural choice in such efforts would be the combination of catalysis and microwave radiation. The main aim of this review is to give an overview of microwave applications in the heterogeneous catalysis, including the preparation of catalysts, as well as explore some selected microwave assisted catalytic reactions. The review is divided into three principal topics: (i) introduction to microwave chemistry and microwave materials processing; (ii) description of the loss mechanisms and microwave-specific effects in heterogeneous catalysis; and (iii) applications of microwaves in some selected chemical processes, including the preparation of heterogeneous catalysts.

scholarly journals A comparative study on quality parameters of pumpkin, melon and sunflower oils during thermal treatment

OCL ◽  
2019 ◽  
Vol 26 ◽  
pp. 32 ◽  
Author(s):  
Zhana Petkova ◽  
Ginka Antova
Keyword(s):  
Fatty Acid Composition ◽  
Fatty Acid ◽  
Thermal Treatment ◽  
Microwave Heating ◽  
Acid Composition ◽  
Seed Oil ◽  
Conventional Heating ◽  
Melon Seed ◽  
Sunflower Oils ◽  
Melon Seed Oil

Current paper reveals the impact of thermal treatment on the quality of two seed oils – pumpkin and melon compared to the quality of the most used oil – sunflower oil. Conventional and microwave heating were used for processing the oils. The duration of the thermal treatment was 9, 12 and 18 min for the conventional heating. The microwave heating was performed with two microwave powers of the equipment (600 W and 900 W) for 3, 6, 9 and 12 min. At every stage of the thermal processing were determined acid and peroxide value, the absorbance of the oils at 232 and 268 nm, tocopherol and fatty acid composition. It was observed that the degree of oxidation of the examined oils during microwave and conventional heating increased with the duration of the thermal process and the power of the microwaves. Also, the two methods of heating had a little impact on the processes leading to the formation of free fatty acids. Total tocopherols of the melon seed oil were more stable to thermal treatment. The amount of linoleic acid decreased in the pumpkin and sunflower oils during microwave treatment, while that of oleic and palmitic acid relatively increased. The biggest change in the fatty acid composition of both oils was found during microwave heating at 900W. The changes in fatty acid composition of thermally treated melon seed oil were insignificant. Overall, melon seed oil was observed to be more thermally stable than pumpkin and sunflower oils.

Comparative study of conventional and microwave heating of polyacrylonitrile-based fibres

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Guozhen Zhao ◽  
Jianhua Liu ◽  
Lei Xu ◽  
Shenghui Guo
Keyword(s):  
Microwave Heating ◽  
Surface Defects ◽  
Energy Dispersive Spectrometer ◽  
Xrd Analysis ◽  
Economic Benefits ◽  
Heating Time ◽  
Oxidation Temperature ◽  
Conventional Heating ◽  
Heating Method ◽  
Molecular Arrangement

Abstract The effects of the conventional heating method and the microwave heating method on polyacrylonitrile-based fibres in the temperature range of 180–280 °C were investigated. Fourier transform infrared spectroscopy, X-ray wide-angle scattering, Raman spectroscopy, energy-dispersive spectrometer, scanning electron microscopy and bulk density were used to characterise the properties of the samples. Results show that the microwave heating method can shorten the pre-oxidation time, reduce pre-oxidation temperature and reduce the number of surface defects. The pre-oxidised fibres obtained by the microwave heating method exhibit not only good crystallite size but also a smooth surface. Atomic morphology and molecular arrangement are orderly inside the fibre. The FT-IR spectrum shows that the oxidation reaction occurs at 220 °C, and the CI value of PAN fibers stabilised by microwave heating is the larger than the fibers stabilised by conventional heating. XRD analysis shows that fibers stabilised by microwave heating have low stack domains. The SEM and Raman spectra indicate that hydrogen peroxide can improve the surface finish of the fibers and reduce defects. Microwave heating can reduce the pre-oxidation temperature by about 20 °C and shorten the heating time. The economic benefits of using this method are significantly improved.

Preparation of WC-TiC-Ni3Al-CaF2 functionally graded self-lubricating tool material by microwave sintering and its cutting performance

2020 ◽  
Vol 39 (1) ◽  
pp. 45-53 ◽  
Author(s):  
Siwen Tang ◽  
Rui Wang ◽  
Pengfei Liu ◽  
Qiulin Niu ◽  
Guoqing Yang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Microwave Heating ◽  
Cutting Performance ◽  
Conventional Heating ◽  
Hard Alloys ◽  
Dry Cutting ◽  
Temperature Oxidation ◽  
Lubricating Material ◽  
Heating Technology

AbstractWith the concern of the environment, green dry cutting technology is getting more and more attention and self-lubricating tool technology plays an important role in dry cutting. Due to the demand for high temperature performance of tools during dry cutting process, cemented carbide with Ni3Al as the binder phase has received extensive attention due to its excellent high temperature strength and high temperature oxidation resistance. In this paper, WC-TiC-Ni3Al-CaF2 graded self-lubricating material and tools were prepared by microwave heating method, and its microstructure, mechanical properties and cutting performance were studied. Results show that gradient self-lubricating material can be quickly prepared by microwave heating technology, and the strength is equivalent to that of conventional heating technology. CaF2 not only plays a role in self-lubrication, but also refines the grain of the material. A reasonable gradient design can improve the mechanical properties of the material. When the gradient distribution exponent is n1 = 2, the material has high mechanical properties. Cutting experiments show that the WC-TiC-Ni3Al-CaF2 functional gradient self-lubricating tool has better cutting performance than the homogeneous WC-TiC-Ni3Al hard alloys.

A comparison of mutagenic PhIP and beneficial 8-C-(E-phenylethenyl)quercetin and 6-C-(E-phenylethenyl)quercetin formation under microwave and conventional heating

2018 ◽  
Vol 9 (7) ◽  
pp. 3853-3859 ◽  
Author(s):  
Daming Fan ◽  
Lijie Li ◽  
Nana Zhang ◽  
Yueliang Zhao ◽  
Ka-Wing Cheng ◽  
...  
Keyword(s):  
Microwave Heating ◽  
Conventional Heating

Microwave heating produced less genotoxic PhIP and more human beneficial 6-CEPQ and 8-CEPQ than conventional heating.

scholarly journals Search for the Microwave Nonthermal Effect in Microwave Chemistry: Synthesis of the Heptyl Butanoate Ester with Microwave Selective Heating of a Sulfonated Activated Carbon Catalyst

Catalysts ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 466
Author(s):  
Daisuke Sakemi ◽  
Nick Serpone ◽  
Satoshi Horikoshi
Keyword(s):  
Activated Carbon ◽  
Moisture Content ◽  
Homogeneous Medium ◽  
Temperature Fields ◽  
Heat Transfer Analysis ◽  
Conventional Heating ◽  
Microwave Chemistry ◽  
Butanoic Acid ◽  
Selective Heating ◽  
Product Yields

The heptyl butanoate ester was synthesized from butanoic acid and heptanol in a heterogeneous medium in the presence of sulfonated activated carbon (AC-SO3H) catalyst particles subjected to microwave irradiation, which led to higher conversion yields (greater product yields) than conventional heating with an oil bath. The advantage of the microwaves appeared only when the moisture content in the butanoic acid batch(es) was high, suggesting that, unlike conventional heating, the reverse reaction caused by the moisture content and/or by the byproduct water was suppressed by the microwaves. This contrasted with the results that were found when carrying out the reaction in a homogeneous medium in the presence of the 2,4,6-trimethylpyridinium-p-toluene sulfonate (TMP-PTS) catalyst, as product yields were not improved by microwave heating relative to conventional heating. The removal of moisture/water content in the reaction solution was more pronounced when the reactor was cooled, as the reaction yields were enhanced via selective heating of the heterogeneous catalyst. A coupled electromagnetic field/heat transfer analysis gave credence to the selective heating of the AC-SO3H catalyst, which was further enhanced by cooling the reactor. It was deduced that unforeseen impurities and local high-temperature fields generated on the surface of small fine catalyst particles may have had an effect on the microwave chemistry such that the associated phenomena could be mistaken as originating from a nonthermal effect of the microwaves. Accordingly, it is highly recommended that impurities and selective heating be taken into consideration when examining and concluding the occurrence of a microwave nonthermal effect.

Application of Microwave Heating for Adhesive Joining

1999 ◽  
Author(s):  
Erik T. Thostenson ◽  
Tsu-Wei Chou
Keyword(s):  
Microwave Heating ◽  
Composite Structures ◽  
Material Selection ◽  
Adhesive System ◽  
Conventional Heating ◽  
Joint Interface ◽  
Microwave Curing ◽  
Composite Joint ◽  
High Dielectric ◽  
Microwave Techniques

Abstract In conventional joining of composite materials and sandwich structures, reductions in processing time are limited by inefficient heat transfer. In conventional processing the thermal energy must diffuse through the composite layers to heat the joint interface and cure the thermosetting adhesive, and this outside-in process of heating results in excessive processing times and wasted energy. The purpose of the current work is to examine microwave heating as an alternative to conventional heating for joining of composite structures. Through proper material selection, microwaves are able to penetrate the substrate materials and cure the adhesives in-situ. Selective heating with microwaves is achieved by incorporating interlayer materials that have high dielectric loss properties relative to the substrate materials. In this study, a processing window for elevated temperature curing of an epoxy paste adhesive system (HYSOL EA 9359.3) was developed and composite joint systems were manufactured using conventional and microwave techniques and tested in shear. Microwave curing resulted in both enhanced shear strength and less scatter in experimental data.

Sign in / Sign up

Export Citation Format

Share Document