scholarly journals Power Generation: Feedstock for High-Value Sulfate Minerals

Minerals ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 188
Author(s):  
Lucian C. Staicu ◽  
Tomasz Bajda ◽  
Lukasz Drewniak ◽  
Laurent Charlet
Keyword(s):  
Metal Removal ◽  
Cost Benefit Analysis ◽  
Cost Benefit ◽  
Raw Material ◽  
Flue Gas Desulfurization ◽  
X Ray Diffraction ◽  
Electron Microscopy Analysis ◽  
One Step ◽  
Microscopy Analysis

Coal-fired power facilities generate a polymetallic effluent (Flue Gas Desulfurization—FGD) rich in sulfate. FGD effluents may be considered an important secondary resource. This paper investigates the recovery of sulfate as barite (BaSO4), a mineral with high commercial value and a critical raw material. Using equimolar BaCl2, >99% desulfurization of an FGD effluent produced by a coal-fired power plant operating in central Poland was achieved, yielding up to 16.5 kg high purity barite m−3. The recovered barite was characterized by X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), thermogravimetric (TGA), scanning electron microscopy analysis (SEM), surface properties (PZC), density, and chemical stability (TCLP), and was compared with a commercial reference material. Barite recovery also led to the reduction in concentration of Al (86%), Cu (52%), K (69%), Mo (62%), Se (40%), Sr (91%), and U (75%) initially present in the FGD effluent. TCLP results indicate the entrapment and the stabilization of ~70% Se and ~90% Al in the barite structure. Based on this dataset, an in-depth characterization of the recovered barite is presented, and the removal mechanism of the elements is discussed. The study also provides a preliminary cost benefit analysis of the process. To our best knowledge, this is the first work showing barite recovery and metal removal from FGD effluents using a one-step process.

SYNTHESIS AND CHARACTERIZATION OF HG-BASED SUPERCONDUCTING THIN FILMS PRODUCED STARTING FROM LASER-DEPOSITED PRECURSORS

2000 ◽  
Vol 14 (25n27) ◽  
pp. 2731-2736 ◽  
Author(s):  
M. BINDI ◽  
F. FUSO ◽  
N. PUCCINI ◽  
E. ARIMONDO ◽  
A. TAMPIERI ◽  
...  
Keyword(s):  
Thin Films ◽  
Laser Deposition ◽  
Precursor Film ◽  
Superconducting Thin Films ◽  
X Ray Diffraction ◽  
X Ray ◽  
Electron Microscopy Analysis ◽  
Zero Resistance ◽  
Microscopy Analysis

Correctly c-axis oriented HgBa 2 CaCu 2 O 6+δ thin films have been produced on (100) MgO single crystal substrates and characterized. Pulsed laser deposition has been exploited to deposit Hg-free Re-doped precursor which then underwent synthesis in evacuated and sealed quartz tubes. X-ray diffraction pattern of the precursor target shows the expected composition of oxides. Scanning electron microscopy analysis have been performed on the surface of the precursor film. Hg-1212 films have been analyzed by θ-2θ Bragg-Brentano X-ray diffractometry. The patterns show little contributions in composition of Hg-1223 phase. The films exhibit a transition temperature >120 K with zero-resistance at around 115 K.

Growth and characterization of NdBa2Cu3O7-x thin films deposited by d.c. sputtering

2000 ◽  
Vol 14 (25n27) ◽  
pp. 2664-2669
Author(s):  
M. C. CUCOLO ◽  
A. M. CUCOLO
Keyword(s):  
Thin Films ◽  
X Ray Diffraction ◽  
Surface Stability ◽  
Deposition Parameters ◽  
High Oxygen Pressure ◽  
Fabrication Procedure ◽  
Electron Microscopy Analysis ◽  
Microscopy Analysis ◽  
Diffraction Patterns

Among the ReBa 2 Cu 3 O 7-x (ReBCO, Re=rare earth) cuprate family the NdBa 2 Cu 3 O 7-x system (NdBCO) is known to have the highest critical temperature and critical current. Moreover, in comparison with the YBa 2 Cu 3 O 7-x compound, NdBCO shows a better surface stability and morfology that are basic requirements for the realization of high temperature superconducting (HTS) devices. We have investigated the fabrication procedure of NdBCO films on (001) SrTiO 3 substrates using a dc sputtering technique in high oxygen pressure. The effect of several deposition parameters on the structural and superconducting properties of the NdBCO thin films, has been investigated. The x-ray diffraction patterns showed that the deposited films were c-axis oriented without any impurity phase. The surface morfology was studied by a standard Scanning Electron Microscopy analysis (SEM). T c (ρ=0) ≥ 91 K and J c (77 K ) ≤ 0.6 106 A/cm 2 have been obtained at the optimized sputtering conditions.

Growth and Characterization of C-Axis Oriented YBa2Cu3O7-x/PrBa2Cu3O7-x Bilayers

1999 ◽  
Vol 13 (09n10) ◽  
pp. 1005-1010 ◽  
Author(s):  
C. Beneduce ◽  
F. Bobba ◽  
M. Boffa ◽  
M. C. Cucolo ◽  
A. M. Cucolo ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
X Ray Diffraction ◽  
Transmission Electron Microscopy Analysis ◽  
X Ray ◽  
Resistivity Measurements ◽  
Transmission Electron ◽  
High Oxygen Pressure ◽  
Electron Microscopy Analysis ◽  
Microscopy Analysis

We report on the preparation and characterization of YBa 2 Cu 3 O 7-x/ PrBa 2 Cu 3 O 7-x bilayers onto (100) SrTiO 3 substrates. The samples have been prepared by sequential dc sputtering processes in high oxygen pressure from stoichiometric targets. The structural characterization of the YBa 2 Cu 3 O 7-x and PrBa 2 Cu 3 O 7-x films and of the bilayers has been performed by means of X-ray diffraction. The Scanning Electron Microscopy analysis has showed that the film surfaces are flat and free of precipitates. A detailed study of the interfaces has been performed by Transmission Electron Microscopy analysis. The electrical resistivity measurements showed for the YBa 2 Cu 3 O 7-x films sharp superconducting transitions at 91.5 K and critical current density of about 106 A/cm 2 at 77 K, while for the PrBa 2 Cu 3 O 7-x films a semiconductor-like behavior has been observed.

scholarly journals A Versatile Approach to Access Trimetallic Complexes Based on Trisphosphinite Ligands

Molecules ◽  
2020 ◽  
Vol 25 (3) ◽  
pp. 593
Author(s):  
Juan Miranda-Pizarro ◽  
Macarena G. Alférez ◽  
M. Dolores Fernández-Martínez ◽  
Eleuterio Álvarez ◽  
Celia Maya ◽  
...  
Keyword(s):  
Coordination Chemistry ◽  
Late Transition Metal ◽  
X Ray Diffraction ◽  
X Ray ◽  
Full Characterization ◽  
Metal Precursors ◽  
Straightforward Method ◽  
One Step ◽  
Late Transition

A straightforward method for the preparation of trisphosphinite ligands in one step, using only commercially available reagents (1,1,1-tris(4-hydroxyphenyl)ethane and chlorophosphines) is described. We have made use of this approach to prepare a small family of four trisphosphinite ligands of formula [CH3C{(C6H4OR2)3], where R stands for Ph (1a), Xyl (1b, Xyl = 2,6-Me2-C6H3), iPr (1c), and Cy (1d). These polyfunctional phosphinites allowed us to investigate their coordination chemistry towards a range of late transition metal precursors. As such, we report here the isolation and full characterization of a number of Au(I), Ag(I), Cu(I), Ir(III), Rh(III) and Ru(II) homotrimetallic complexes, including the structural characterization by X-ray diffraction studies of six of these compounds. We have observed that the flexibility of these trisphosphinites enables a variety of conformations for the different trimetallic species.

Characterization and A Preliminary Study of TiO2 Synthesis from Lampung Iron Sand

2020 ◽  
Vol 849 ◽  
pp. 113-118
Author(s):  
Yayat Iman Supriyatna ◽  
Slamet Sumardi ◽  
Widi Astuti ◽  
Athessia N. Nainggolan ◽  
Ajeng W. Ismail ◽  
...  
Keyword(s):  
Food Packaging ◽  
Xrd Analysis ◽  
Major Elements ◽  
Raw Material ◽  
Solid Residue ◽  
X Ray Diffraction ◽  
X Ray ◽  
Leaching Solution ◽  
Ti Content

The purpose of this study is to characterize Lampung iron sand and to conduct preliminary experiments on the TiO2 synthesis which can be used for the manufacturing of functional food packaging. The iron sand from South Lampung Regency, Lampung Province that will be utilized as raw material. The experiment was initiated by sieving the iron sand on 80, 100, 150, 200 and 325 mesh sieves. Analysis using X-Ray Fluorescence (XRF) to determine the element content and X-Ray Diffraction (XRD) to observe the mineralization of the iron sand was conducted. The experiment was carried out through the stages of leaching, precipitation, and calcination. Roasting was applied firstly by putting the iron sand into the muffle furnace for 5 hours at a temperature of 700°C. Followed by leaching using HCl for 48 hours and heated at 105°C with a stirring speed of 300 rpm. The leaching solution was filtered with filtrate and solid residue as products. The solid residue was then leached using 10% H2O2 solution. The leached filtrate was heated at 105°C for 40 minutes resulting TiO2 precipitates (powder). Further, the powder was calcined and characterized. Characterization of raw material using XRF shows the major elements of Fe, Ti, Mg, Si, Al and Ca. The highest Ti content is found in mesh 200 with 9.6%, while iron content is about 80.7%. While from the XRD analysis, it shows five mineral types namely magnetite (Fe3O4), Rhodonite (Mn, Fe, Mg, Ca) SiO3, Quart (SiO2), Ilmenite (FeOTiO2) and Rutile (TiO2). The preliminary experiment showed that the Ti content in the synthesized TiO2 powder is 21.2%. The purity of TiO2 is low due to the presence of Fe metal which is dissolved during leaching, so that prior to precipitation purification is needed to remove impurities such as iron and other metals.

Preliminary Preparation and Characterization Studies of Cellulose from Merbau (Intsia bijuga)

2012 ◽  
Vol 620 ◽  
pp. 314-319
Author(s):  
Nur Amira Mamat Razali ◽  
Fauziah Abdul Aziz ◽  
Saadah Abdul Rahman
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Alkaline Treatment ◽  
Raw Material ◽  
X Ray Diffraction ◽  
X Ray ◽  
Preliminary Preparation ◽  
Characterization Studies ◽  
Scanning Electron

Hardwood is wood from angiosperm trees. The characteristic of hardwood include flowers, endosperm within seeds and the production of fruits that contain the seeds. This paper aims to discuss the preparation and characterization of cellulose obtained from hardwood. The hardwood Merbau (Intsia bijuga) was chosen as raw material in this study. Alkaline treatment and delignification methods were used for the preparation of cellulose. Acid hydrolysis was employed to produce cellulose nanocrystal (CNC). The treated and untreated samples were characterized using x-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM). The final product, from both trated and untreated samples were then compared.

One Step Synthesis and Characterization of Zirconia-Graphene Composites

2012 ◽  
Vol 600 ◽  
pp. 174-177 ◽  
Author(s):  
Jian Fei Xia ◽  
Zong Hua Wang ◽  
Yan Zhi Xia ◽  
Fei Fei Zhang ◽  
Fu Qiang Zhu ◽  
...  
Keyword(s):  
Synthesis And Characterization ◽  
Two Dimensional ◽  
X Ray Diffraction ◽  
X Ray ◽  
Graphene Composite ◽  
Transmission Electron ◽  
One Step ◽  
Ft Ir ◽  
Xrd Techniques

Zirconia-graphene composite (ZrO2-G) has been successfully synthesized via decomposition of ZrOCl2•6H2O in a water-isopropanol system with dispersed graphene oxide (GO) utilizing Na2S as a precursor could enable the occurrence of the deposition of Zr4+ and the deoxygenation of GO at the same time. Transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FT-IR) and X-ray diffraction (XRD) techniques were used to characterize the samples. It was found that graphene were fully coated with ZrO2, and the ZrO2 existing in tetragonal phase, which resulted in the formation of two-dimensional composite.

scholarly journals The ALARP Principle in the Cost-Benefit Analysis for the Acceptability of Investment Risk

2018 ◽  
Vol 10 (12) ◽  
pp. 4668 ◽  
Author(s):  
Antonio Nesticò ◽  
Shuquan He ◽  
Gianluigi De Mare ◽  
Renato Benintendi ◽  
Gabriella Maselli
Keyword(s):  
Cost Benefit Analysis ◽  
Risk Mitigation ◽  
Cost Benefit ◽  
Economic Evaluations ◽  
Investment Risk ◽  
Benefit Analysis ◽  
Mitigation Design ◽  
The Cost

The process of allocating financial resources is extremely complex—both because the selection of investments depends on multiple, and interrelated, variables, and constraints that limit the eligibility domain of the solutions, and because the feasibility of projects is influenced by risk factors. In this sense, it is essential to develop economic evaluations on a probabilistic basis. Nevertheless, for the civil engineering sector, the literature emphasizes the centrality of risk management, in order to establish interventions for risk mitigation. On the other hand, few methodologies are available to systematically compare ante and post mitigation design risk, along with the verification of the economic convenience of these actions. The aim of the paper is to demonstrate how these limits can be at least partially overcome by integrating, in the traditional Cost-Benefit Analysis schemes, the As Low as Reasonably Practicable (ALARP) logic. According to it, the risk is tolerable only if it is impossible to reduce it further or if the costs to mitigate it are disproportionate to the benefits obtainable. The research outlines the phases of an innovative protocol for managing investment risks. On the basis of a case study dealing with a project for the recovery and transformation of an ancient medieval village into a widespread-hotel, the novelty of the model consists of the characterization of acceptability and tolerability thresholds of the investment risk, as well as its ability to guarantee the triangular balance between risks, costs and benefits deriving from mitigation options.

scholarly journals Making and Characterization of Limnpo4 Using Solid State Reaction Method for Lithium Ion Battery Cathodes

2019 ◽  
pp. 583-588
Author(s):  
Adelyna Oktavia ◽  
Kurnia Sembiring ◽  
Slamet Priyono
Keyword(s):  
Solid State ◽  
Lithium Ion Battery ◽  
Lithium Ion ◽  
Solid State Reaction Method ◽  
Raw Material ◽  
X Ray Diffraction ◽  
Solid State Method ◽  
X Ray ◽  
General Investigation

Hospho-material of olivine, LiMnPO4 identified as promising for cathode material generation next Lithium-ion battery and has been successfully synthesized by solid-state method with Li2Co3, 2MnO2, 2NH4H2PO4 as raw material. The influence of initial concentration of precursors at kalsinasi temperatures (400-800 ° C) flows with nitrogen. The purity and composition phase verified by x-ray diffraction analysis (XRD), scanning electron microscopy (SEM), spectroscopy, energy Dispersive x-ray Analysis (EDS), Raman spectra. General investigation shows that there is a correlation between the concentration of precursors, the temperature and the temperature of sintering kalsinasi that can be exploited to design lithium-ion next generation.

Preparation, Characterization of Nonmetal Doped TiO2 Nanoparticles with their Excellent Photocatalystic Properties

2011 ◽  
Vol 183-185 ◽  
pp. 2254-2257
Author(s):  
Ying Wei Wang ◽  
Yu Fei Li ◽  
Pei Han Yang
Keyword(s):  
Photoelectron Spectroscopy ◽  
Photocatalytic Performance ◽  
Anatase Phase ◽  
Titania Nanoparticles ◽  
X Ray Diffraction ◽  
X Ray ◽  
One Step ◽  
Doped Titania ◽  
Nonmetal Doping

Nonmetal (S, P) doped titania nanoparticles were synthesized by a one step hydrothermal method. These samples were calcined with different temperature, the sample exist in anatase phase has much higher photocatalytic activity for methylene blue (MB) degradation. The visible response and the higher UV activity of the different nonmetal doped TiO2make it possible to utilize solar energy efficiently to execute photocatalysis processes. The resulting materials were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), etc. It can conclude the nonmetal doping TiO2proves to be more suitable to improve the photocatalytic performance.

Sign in / Sign up

Export Citation Format

Share Document