scholarly journals A Comprehensive Investigation on Development of Lightweight Aluminium Miniature Gears by Thermoelectric Erosion Machining Process

Micromachines ◽  
2021 ◽  
Vol 12 (10) ◽  
pp. 1230
Author(s):  
Sujeet Kumar Chaubey ◽  
Neelesh Kumar Jain ◽  
Kapil Gupta
Keyword(s):  
Surface Roughness ◽  
Cutting Speed ◽  
Spur Gear ◽  
Microscopic Investigation ◽  
Quality Parameters ◽  
Machining Process ◽  
Manufacturing Quality ◽  
Research And Innovation ◽  
Pulse On Time ◽  
Pulse Off Time

Nowadays, size, weight, and durability are crucial factors in product development that draw the attention of many researchers and engineers towards research and innovation in the micromanufacturing area. This paper reports on the development of a lightweight aluminium gear of miniature size with a bore and hub using wire-assisted thermoelectric erosion machining (WTEM). The external spur gear was cut from 7075 aluminium alloy round stepped gear blank by WTEM using 0.25 mm brass wire. Further, the miniature gear was tested for various manufacturing quality parameters such as microgeometry, surface roughness, and microstructure, along with evaluating process productivity in terms of volumetric gear cutting speed To understand the mechanism of development of aluminium miniature gear, an investigation on the influence of WTEM parameters namely servo-voltage, pulse-on time, pulse-off time, and wire speed on surface roughness was conducted. A total of 18 gears were fabricated following Taguchi L9 (34) orthogonal array approach of design of experiments considering the randomization and replication. A typical average surface roughness value of 1.58 μm and manufacturing quality of DIN standard number 7 based on gear microgeometry were successfully achieved. Microscopic investigation revealed uniform and accurate tooth profiles, flank surfaces free from burrs and contaminants, and uniform microstructure that confirm the good performance characteristics of the developed lightweight miniature gear of aluminium. This investigation will add new results in the field as regards the development of lightweight microparts.

scholarly journals Study of wire-electrical discharge machining parameters of titanium alloy by using taguchi method

2018 ◽  
Vol 7 (2.8) ◽  
pp. 10
Author(s):  
A VS Ram Prasad ◽  
Koona Ramji ◽  
B Raghu Kumar
Keyword(s):  
Surface Roughness ◽  
Taguchi Method ◽  
Process Parameters ◽  
Optimization Technique ◽  
Machining Process ◽  
Machining Parameters ◽  
Wire Edm ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Edm Process

Machining of Titanium alloys is difficult due to their chemical and physical properties namely excellent strength, chemical reactivity and low thermal conductivity. Traditional machining of such materials leads to formation of continuous chips and tool bits are subjected to chatter which leads to formation of poor surface on machined surface. In this study, Wire-EDM one of the most popular unconventional machining process which was used to machine such difficult-to-cut materials. Effect of Wire-EDM process parameters namely peak current, pulse-on- time, pulse-off-time, servo voltage on MRRand SR was investigated by Taguchi method. 0.25 mm brass wire was used in this process as electrode material. A surface roughness tester (Surftest 301) was used to measure surface roughness value of the machined work surface. A multi-response optimization technique was then utilized to optimize Wire-EDM process parameters for achieving maximum MRR and minimum SR simultaneously.

scholarly journals Findings of performance evaluation of EDM for different materials of electrodes and work pieces- a review

2018 ◽  
Vol 7 (4.5) ◽  
pp. 542
Author(s):  
Harshalkumar R. Mundane ◽  
Dr. A. V. Kale ◽  
Dr. J. P. Giri
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Performance Measure ◽  
Machining Process ◽  
Machining Parameters ◽  
Spark Erosion ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time ◽  
Time Pulse

EDM (Spark erosion) is non-conventional machining process which uses as removing unwanted material by electrical spark erosion. EDM Machining parameters affecting to the performance and the industries goal is to produce high quality of product with less time consuming and cost. To achieve these goals, optimizing the machining parameters such as pulse on time, pulse off time, cutting speed, depth of cut, duty cycle, arc gap, voltage etc. The performance measure of EDM is calculated on the basis of Material Remove Rate(MRR), Tool Wear Rate(TWR), and Surface Roughness(SR).The main objective of present work is to investigate of the influence of input EDM (Electro Discharge Machining) parameters on machining characteristics like surface roughness and the effects of various EDM process parameters such as pulse on time, pulse off time, servo voltage, peak current, dielectric flow rate, on different process response parameters such as material removal rate (MRR), surface roughness (Ra), Kerf (width of Cut), tool wear ratio(TWR)and surface integrity factors. In this paper few selected research paper related to Die-sinker EDM with effect of MRR, TWR, surface roughness (SR) and work piece material have been discussed.   

scholarly journals Precision Machining of Nimonic C 263 Super AlloyUsing WEDM

Coatings ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 590
Author(s):  
Katerina Mouralova ◽  
Libor Benes ◽  
Josef Bednar ◽  
Radim Zahradnicek ◽  
Tomas Prokes ◽  
...  
Keyword(s):  
Electrical Discharge ◽  
Cutting Speed ◽  
Machining Process ◽  
Precision Machining ◽  
Machining Accuracy ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Super Alloy ◽  
Machined Surfaces

Wire electrical discharge machining (WEDM) is an unconventional and very efficient technology for precision machining of the Nimonic C 263 super alloy, which is very widespread, especially in the energy, aerospace and automotive industries. Due to electrical discharge, defects in the form of cracks or burned cavities often occur on the machined surfaces, which negatively affect the correct functionality and service life of the manufactured components. To increase the efficiency of the machining of Nimonic C 263 using WEDM, in this study, extensive design of experiments was carried out, monitoring input factors in the form of machine parameters like Pulse off time, Gap voltage, Discharge current, Pulse on time and Wire feed, the output of which was comprehensive information about the behaviour of such machined surfaces, which allowed the optimization of the entire machining process. Thus, the optimization of the Cutting speed was performed in relation to the quality of the machined surface and the machining accuracy, as well as an analysis of the chemical composition of the machined surfaces and a detailed analysis of the lamella using a transmission electron microscope. A detailed study of the occurrence of surface or subsurface defects was also included. It was found that with the help of complex optimization tools, it is possible to significantly increase the efficiency of the machining of the Nimonic C 263 super alloy and achieve both financial savings in the form of shortened machine time and increasing the quality of machined surfaces.

Optimization of Machining Condition in WEDM for Titanium Grade 6 Using MOORA Coupled with PCA — A Multivariate Hybrid Approach

2017 ◽  
Vol 16 (02) ◽  
pp. 81-99 ◽  
Author(s):  
Himadri Majumder ◽  
Kalipada Maity
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Hybrid Approach ◽  
Cutting Speed ◽  
Kerf Width ◽  
Average Surface Roughness ◽  
Average Surface ◽  
Titanium Grade ◽  
Pulse On Time ◽  
Pulse Off Time

This paper represents a multivariate hybrid approach, combining Multi-Objective Optimization on the basis of Ratio Analysis (MOORA) and Principal Component Analysis (PCA) to optimize different correlated responses during Wire Electrical Discharge Machining (WEDM) process of titanium grade 6. The response parameters selected are the average cutting speed, average Kerf width and average surface roughness (Ra). All of them have been studied in terms of pulse-ON time, pulse-OFF time, wire feed and wire tension. As indicated by Taguchi’s signal-to-noise ratio, the optimum process parameters were achieved for the desired average cutting speed, average Kerf width and average surface roughness, respectively. At last, the optimum combination of process parameters was validated by affirmation test which gave considerably improved various quality characteristics. Confirmation test outcome revealed that multivariate hybrid approach MOORA coupled with PCA was a competent strategy to decide available cutting parameters for a desired response quality for WEDM of titanium grade 6.

scholarly journals Surface Roughness Prediction for Steel 304 In Edm Using Response Graph Modeling

2018 ◽  
Vol 14 (4) ◽  
pp. 115-124 ◽  
Author(s):  
Shukry H. Aghdeab ◽  
Nareen Hafidh Obaeed ◽  
Marwa Qasim Ibraheem
Keyword(s):  
Surface Roughness ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Machining Process ◽  
Applied Current ◽  
Graph Modeling ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
The Impact ◽  
Off Time

Electrical Discharge Machining (EDM) is a non-traditional cutting technique for metals removing which is relied upon the basic fact that negligible tool force is produced during the machining process. Also, electrical discharge machining is used in manufacturing very hard materials that are electrically conductive. Regarding the electrical discharge machining procedure, the most significant factor of the cutting parameter is the surface roughness (Ra). Conventional try and error method is time consuming as well as high cost. The purpose of the present research is to develop a mathematical model using response graph modeling (RGM). The impact of various parameters such as (current, pulsation on time and pulsation off time) are studied on the surface roughness in the present research. 27 samples were run by using CNC-EDM machine which used for cutting steel 304 with dielectric solution of gas oil by supplied DC current values (10, 20, and 30A). Voltage of (140V) uses to cut 1.7mm thickness of the steel and use the copper electrode. The result from this work is useful to be implemented in industry to reduce the time and cost of Ra prediction. It is observed from response table and response graph that the applied current and pulse on time have the most influence parameters of surface roughness while pulse off time has less influence parameter on it. The supreme and least surface roughness, which is achieved from all the 27 experiments is (4.02 and 2.12µm), respectively. The qualitative assessment reveals that the surface roughness increases as the applied current and pulse on time increases

Surface Study in a Non-conventional (Electrical Discharge Machining) Process for Grade 6 Titanium Material

2014 ◽  
Vol 68 (1) ◽  
Author(s):  
Md. Ashikur Rahman Khan ◽  
M. M. Rahman
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Machining Process ◽  
Machined Surface ◽  
Titanium Material ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time

Electrical discharge machining (EDM) produces complex shapes and permits high-precision machining of any hard or difficult-to-cut materials. The performance characteristics such as surface roughness and microstructure of the machined face are influenced by numerous parameters. The selection of parameters becomes complicated. Thus, the surface roughness (Ra) and microstructure of the machined surface in EDM on Grade 6 titanium alloy are studied is this study. The experimental work is performed using copper as electrode material. The polarity of the electrode is maintained as negative. The process parameters taken into account in this study are peak current (Ip), pulse-on time (Ton), pulse-off time (Toff), and servo-voltage (Sv). A smooth surface finish is found at low pulse current, small on-time and high off-time. The servo-voltage affects the roughness diversely however, a finish surface is found at 80 V Sv. Craters, cracks and globules of debris are appeared in the microstructure of the machined part. The size and degree of craters as well as cracks increase with increasing in energy level. Low discharge energy yields an even surface. This approach helps in selecting proper process parameters resulting in economic EDM machining. 

Effects of Process Parameters on Material Removal Rate and Surface Roughness in Wedm of H-13 Die Tool Steel

2018 ◽  
Vol 28 ◽  
pp. 55-66 ◽  
Author(s):  
Kuldeep Singh ◽  
Khushdeep Goyal ◽  
Deepak Kumar Goyal
Keyword(s):  
Surface Roughness ◽  
Taguchi Method ◽  
Tool Steel ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Pulse On Time ◽  
Pulse Off Time

In research work variation of cutting performance with pulse on time, pulse off time, wire type, and peak current were experimentally investigated in wire electric discharge machining (WEDM) process. Soft brass wire and zinc coated diffused wire with 0.25 mm diameter and Die tool steel H-13 with 155 mm× 70 mm×14 mm dimensions were used as tool and work materials in the experiments. Surface roughness and material removal rate (MRR) were considered as performance output in this study. Taguchi method was used for designing the experiments and optimal combination of WEDM parameters for proper machining of Die tool steel (H-13) to achieve better surface finish and material removal rate. In addition the most significant cutting parameter is determined by using analysis of variance (ANOVA). Keywords Machining, Process Parameters, Material removal rate, Surface roughness, Taguchi method

Influence of Some Factors on Surface Roughness Parameters at Electrical Discharge Machining

2014 ◽  
Vol 657 ◽  
pp. 291-295 ◽  
Author(s):  
Vasile Ciubotariu ◽  
Adrian Câcu ◽  
Ioana Andreea Rotundu ◽  
Marius Marian Cucoş ◽  
Margareta Coteaţă
Keyword(s):  
Surface Roughness ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Operating Conditions ◽  
Machining Process ◽  
Roughness Parameters ◽  
Power Functions ◽  
Surface Roughness Parameters ◽  
Pulse On Time ◽  
Pulse Off Time

There are various electrical discharge machining techniques and experimental researches could be necessary in order to establish the operating conditions for an optimal machining process. Some theoretical considerations concerning the process of generating the surface asperities as a consequence of the electrical discharge machining process were elaborated. Experimental method was applied in order to evaluate influence exerted by some input factors (pulse on time, pulse off time, average intensity of electric current) on certain surface roughness parameters (Ra, Rz, Ry and Rq). One developed an experimental research by using a copper tool electrode and a workpiece made of high speed steel, in accordance with the requirements specific to a complete factorial experiment with three independent variables at three levels. A ram electrical discharge machine was used as machining equipment. One measured the surface roughness parameters specific to the machined surfaces. Empirical mathematical models of type power functions were established by using the method of least squares.

Optimization of Wedm Parameters for Surface Roughness on Hybrid Mmcs

2014 ◽  
Vol 23 (3) ◽  
pp. 096369351402300
Author(s):  
D. Satishkumar ◽  
M. Kanthababu
Keyword(s):  
Surface Roughness ◽  
Electrical Discharge Machining ◽  
Machining Process ◽  
Matrix Composites ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time ◽  
Unconventional Machining ◽  
Central Composite ◽  
Wire Feed

Metals or alloys when reinforced with more than one reinforcement materials are generally considered as hybrid metal matrix composites (MMCs). The superior properties of the hybrid MMCs deter its wide applications due to the difficulty in machining. Wire electrical discharge machining (WEDM) is an effective unconventional machining process which can be used to machine difficult to machine materials. This work is aimed towards optimizing the WEDM parameters to achieve better surface roughness ( Ra) during machining of stir cast unreinforced A17075 alloy and A17075/B4C/Al2O3 based hybrid MMCS. The experiments were carried out as per central composite design of response surface methodology (RSM). It is observed that all the process parameters such as pulse-on time ( TON), pulse-off time ( TOFF), wire feed (F), gap voltage (V) considered in this work were significant.

scholarly journals Performance evaluation of wire electrical discharge machining on Titanium Alloy

2018 ◽  
Vol 1 (1) ◽  
pp. 27-38
Author(s):  
Jun Qi Tan ◽  
Mohd Yazid Abu
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Cutting Speed ◽  
Wire Electrical Discharge Machining ◽  
Machining Parameters ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Machining Parameter

The experimental carried out to aim at the selection of the best condition machining parameter combination for wire electrical discharge machining (WEDM) of titanium alloy (Ti–6Al–4V). By using Design Expert 10 software, a series of experiments were performed by selecting pulse-on time, pulse-off time, servo voltage and peak current as parameters. The responses that considered were cutting speed, material removal rate, sparking gap and surface roughness. Based on ANOVA analysis, the effect from the parameters on the responses was determined. The optimum machining parameters setting for the maximum cutting speed, minimum sparking gap and minimum surface roughness were found by proceed optimization experiment. Then, each optimization response had their own combination setting on WEDM to cut titanium alloy. 3D response surface graph such as dome and bowl shape represent maximum and minimum point for the solutions had shown in the report. Finally, predicted and actual value from the experiment have been calculated for validation.

Sign in / Sign up

Export Citation Format

Share Document