scholarly journals Fused Filament Fabrication (FFF) for Manufacturing of Microfluidic Micromixers: An Experimental Study on the Effect of Process Variables in Printed Microfluidic Micromixers

Micromachines ◽  
2021 ◽  
Vol 12 (8) ◽  
pp. 858
Author(s):  
Mojtaba Zeraatkar ◽  
Marco D. de Tullio ◽  
Gianluca Percoco
Keyword(s):  
3D Printing ◽  
Soft Lithography ◽  
Microfluidic Devices ◽  
Mixing Process ◽  
Process Variables ◽  
Automated Assembly ◽  
Fused Filament Fabrication ◽  
Mixing Performance ◽  
Geometrical Features ◽  
Manufacturing Methods

The need for accessible and inexpensive microfluidic devices requires new manufacturing methods and materials as a replacement for traditional soft lithography and polydimethylsiloxane (PDMS). Recently, with the advent of modern additive manufacturing (AM) techniques, 3D printing has attracted attention for its use in the fabrication of microfluidic devices and due to its automated, assembly-free 3D fabrication, rapidly decreasing cost, and fast-improving resolution and throughput. Here, fused filament fabrication (FFF) 3D printing was used to create microfluidic micromixers and enhance the mixing process, which has been identified as a challenge in microfluidic devices. A design of experiment (DoE) was performed on the effects of studied parameters in devices that were printed by FFF. The results of the colorimetric approach showed the effects of different parameters on the mixing process and on the enhancement of the mixing performance in printed devices. The presence of the geometrical features on the microchannels can act as ridges due to the nature of the FFF process. In comparison to passive and active methods, no complexity was added in the fabrication process, and the ridges are an inherent property of the FFF process.

scholarly journals Rapid and Inexpensive Fabrication of Multi-Depth Microfluidic Device using High-Resolution LCD Stereolithographic 3D Printing

2019 ◽  
Vol 3 (1) ◽  
pp. 26 ◽  
Author(s):  
Mohamed Mohamed ◽  
Hitendra Kumar ◽  
Zongjie Wang ◽  
Nicholas Martin ◽  
Barry Mills ◽  
...  
Keyword(s):  
High Resolution ◽  
3D Printing ◽  
Soft Lithography ◽  
Liquid Crystal Display ◽  
Three Dimensional ◽  
Microfluidic Devices ◽  
Single Step ◽  
Droplet Generator ◽  
Rapid Fabrication ◽  
Printing System

With the dramatic increment of complexity, more microfluidic devices require 3D structures, such as multi-depth and -layer channels. The traditional multi-step photolithography is time-consuming and labor-intensive and also requires precise alignment during the fabrication of microfluidic devices. Here, we present an inexpensive, single-step, and rapid fabrication method for multi-depth microfluidic devices using a high-resolution liquid crystal display (LCD) stereolithographic (SLA) three-dimensional (3D) printing system. With the pixel size down to 47.25 μm, the feature resolutions in the horizontal and vertical directions are 150 μm and 50 μm, respectively. The multi-depth molds were successfully printed at the same time and the multi-depth features were transferred properly to the polydimethylsiloxane (PDMS) having multi-depth channels via soft lithography. A flow-focusing droplet generator with a multi-depth channel was fabricated using the presented 3D printing method. Experimental results show that the multi-depth channel could manipulate the morphology and size of droplets, which is desired for many engineering applications. Taken together, LCD SLA 3D printing is an excellent alternative method to the multi-step photolithography for the fabrication of multi-depth microfluidic devices. Taking the advantages of its controllability, cost-effectiveness, and acceptable resolution, LCD SLA 3D printing can have a great potential to fabricate 3D microfluidic devices.

scholarly journals Cheap, Versatile, and Turnkey Fabrication of Microfluidic Master Molds Using Consumer Grade LCD Stereolithography 3D Printing

2021 ◽  
Author(s):  
Vincent G. Colin ◽  
Théo A. Travers ◽  
Denis Gindre ◽  
Régis Barillé ◽  
Matthieu Loumaigne
Keyword(s):  
High Resolution ◽  
3D Printing ◽  
Cost Efficiency ◽  
Soft Lithography ◽  
Microfluidic Devices ◽  
Teaching Tool ◽  
3D Printer ◽  
Uv Led ◽  
Led Array ◽  
3D Printers

Abstract The recent development of 3D printers allowed a lot of limitations in the field of microfabrication to be circumvented. The ever-growing chase for smaller dimensions has come to an end in domains such as microfluidics, and the focus now shifted to a cost-efficiency challenge. In this paper, the use of a high-resolution stereolithography LCD 3D printer is investigated for fast and cheap production of microfluidic master molds. More precisely, we use the UV LED array and the LCD matrix of the printer as an illuminator and a programmable photomask for soft lithography. The achieved resolution of around 100µm is mainly limited by the pixel geometry of the LCD matrix. A tree-shape gradient mixer was fabricated using the presented method. It shows very good performances despite the presence of sidewall ripples due to the uneven pixel geometry of the LCD matrix. Given its sub-€1,000 cost, this method is a very good entry point for labs wishing to explore the potential of microfluidic devices in their experiments, as well as a teaching tool for introducing students to microfluidics.

scholarly journals 3D printed self-supporting elastomeric structures for multifunctional microfluidics

2020 ◽  
Vol 6 (41) ◽  
pp. eabc9846 ◽  
Author(s):  
Ruitao Su ◽  
Jiaxuan Wen ◽  
Qun Su ◽  
Michael S. Wiederoder ◽  
Steven J. Koester ◽  
...  
Keyword(s):  
Soft Lithography ◽  
Dna Microarrays ◽  
Microfluidic Devices ◽  
The Self ◽  
Jet Printing ◽  
3D Printed ◽  
Manufacturing Methods ◽  
Sacrificial Materials ◽  
Electronic Sensors ◽  
Supporting Materials

Microfluidic devices fabricated via soft lithography have demonstrated compelling applications such as lab-on-a-chip diagnostics, DNA microarrays, and cell-based assays. These technologies could be further developed by directly integrating microfluidics with electronic sensors and curvilinear substrates as well as improved automation for higher throughput. Current additive manufacturing methods, such as stereolithography and multi-jet printing, tend to contaminate substrates with uncured resins or supporting materials during printing. Here, we present a printing methodology based on precisely extruding viscoelastic inks into self-supporting microchannels and chambers without requiring sacrificial materials. We demonstrate that, in the submillimeter regime, the yield strength of the as-extruded silicone ink is sufficient to prevent creep within a certain angular range. Printing toolpaths are specifically designed to realize leakage-free connections between channels and chambers, T-shaped intersections, and overlapping channels. The self-supporting microfluidic structures enable the automatable fabrication of multifunctional devices, including multimaterial mixers, microfluidic-integrated sensors, automation components, and 3D microfluidics.

scholarly journals A rapid-prototyped moulding system towards optimised scalable fabrication of elastomeric microfluidic devices

2021 ◽  
Author(s):  
Christine Poon ◽  
Albert Fahrenbach
Keyword(s):  
3D Printing ◽  
Microfluidic Device ◽  
Lean Manufacturing ◽  
Soft Lithography ◽  
Low Cost ◽  
Microfluidic Devices ◽  
Petri Dish ◽  
Device Fabrication ◽  
Alternative Techniques ◽  
Optimisation Techniques

3D printing and makerspace technologies are increasingly explored as alternative techniques to soft lithography for making microfluidic devices, and for their potential to segue towards scalable commercial fabrication. Here we considered the optimal application of current benchtop 3D printing for microfluidic device fabrication through the lens of lean manufacturing and present a straightforward but robust rapid prototyped moulding system that enables easy estimation of more precise quantities of polydimethylsiloxane (PDMS) required per device to reduce waste and importantly, making devices with better defined depths and volumes for (i) modelling gas exchange and (ii) fabrication consistency as required for quality-controlled production. We demonstrate that this low-cost moulding step can enable a 40 – 300% reduction in the amount of PDMS required for making individual devices compared to the established method of curing approximately 30 grams of PDMS prepolymer overlaid on a 4” silicon wafer master in a standard plastic petri dish. Other process optimisation techniques were also investigated and are recommended as readily implementable changes to current laboratory and foundry-level microfluidic device fabrication protocols for making devices either out of PDMS or other elastomers. Simple calculators are provided as a step towards more streamlined, software controlled and automated design-to-fabrication workflows for both custom and scalable lean manufacturing of microfluidic devices.

scholarly journals A rapid-prototyped moulding system towards optimised scalable fabrication of elastomeric microfluidic devices

2021 ◽  
Author(s):  
Christine Poon ◽  
Albert Fahrenbach
Keyword(s):  
3D Printing ◽  
Microfluidic Device ◽  
Lean Manufacturing ◽  
Soft Lithography ◽  
Low Cost ◽  
Microfluidic Devices ◽  
Petri Dish ◽  
Device Fabrication ◽  
Alternative Techniques ◽  
Optimisation Techniques

3D printing and makerspace technologies are increasingly explored as alternative techniques to soft lithography for making microfluidic devices, and for their potential to segue towards scalable commercial fabrication. Here we considered the optimal application of current benchtop 3D printing for microfluidic device fabrication through the lens of lean manufacturing and present a straightforward but robust rapid prototyped moulding system that enables easy estimation of more precise quantities of polydimethylsiloxane (PDMS) required per device to reduce waste and importantly, making devices with better defined depths and volumes for (i) modelling gas exchange and (ii) fabrication consistency as required for quality-controlled production. We demonstrate that this low-cost moulding step can enable a 40 – 300% reduction in the amount of PDMS required for making individual devices compared to the established method of curing approximately 30 grams of PDMS prepolymer overlaid on a 4” silicon wafer master in a standard plastic petri dish. Other process optimisation techniques were also investigated and are recommended as readily implementable changes to current laboratory and foundry-level microfluidic device fabrication protocols for making devices either out of PDMS or other elastomers. Simple calculators are provided as a step towards more streamlined, software controlled and automated design-to-fabrication workflows for both custom and scalable lean manufacturing of microfluidic devices.

scholarly journals The Direct 3D Printing of Functional PEEK/Hydroxyapatite Composites via a Fused Filament Fabrication Approach

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 545
Author(s):  
Krzysztof Rodzeń ◽  
Preetam K. Sharma ◽  
Alistair McIlhagger ◽  
Mozaffar Mokhtari ◽  
Foram Dave ◽  
...  
Keyword(s):  
Tensile Strength ◽  
3D Printing ◽  
Selective Laser Sintering ◽  
Fused Filament Fabrication ◽  
Bone Apposition ◽  
Innovative Solutions ◽  
3D Printed ◽  
Work Samples ◽  
Viable Approach ◽  
Crystalline Domains

The manufacture of polyetheretherketone/hydroxyapatite (PEEK/HA) composites is seen as a viable approach to help enhance direct bone apposition in orthopaedic implants. A range of methods have been used to produce composites, including Selective Laser Sintering and injection moulding. Such techniques have drawbacks and lack flexibility to manufacture complex, custom-designed implants. 3D printing gets around many of the restraints and provides new opportunities for innovative solutions that are structurally suited to meet the needs of the patient. This work reports the direct 3D printing of extruded PEEK/HA composite filaments via a Fused Filament Fabrication (FFF) approach. In this work samples are 3D printed by a custom modified commercial printer Ultimaker 2+ (UM2+). SEM-EDX and µCT analyses show that HA particles are evenly distributed throughout the bulk and across the surface of the native 3D printed samples, with XRD highlighting up to 50% crystallinity and crystalline domains clearly observed in SEM and HR-TEM analyses. This highlights the favourable temperature conditions during 3D printing. The yield stress and ultimate tensile strength obtained for all the samples are comparable to human femoral cortical bone. The results show how FFF 3D printing of PEEK/HA composites up to 30 wt% HA can be achieved.

Fused Filament Fabrication 3D Printed Polylactic Acid Electroosmotic Pumps

Lab on a Chip ◽  
2021 ◽  
Author(s):  
Liang Wu ◽  
Stephen Beirne ◽  
Joan-Marc Cabot Canyelles ◽  
Brett Paull ◽  
Gordon G. Wallace ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
3D Printing ◽  
Polylactic Acid ◽  
Fused Filament Fabrication ◽  
Flexible Approach ◽  
Electroosmotic Pump ◽  
3D Printed ◽  
Electroosmotic Pumps

Additive manufacturing (3D printing) offers a flexible approach for the production of bespoke microfluidic structures such as the electroosmotic pump. Here a readily accessible fused filament fabrication (FFF) 3D printing...

scholarly journals Gaining a better understanding of the extrusion process in fused filament fabrication 3D printing: a review

2021 ◽  
Author(s):  
Bahaa Shaqour ◽  
Mohammad Abuabiah ◽  
Salameh Abdel-Fattah ◽  
Adel Juaidi ◽  
Ramez Abdallah ◽  
...  
Keyword(s):  
3D Printing ◽  
Numerical Models ◽  
Extrusion Process ◽  
Analytical Models ◽  
Limiting Factor ◽  
Fused Filament Fabrication ◽  
Promising Tool ◽  
Relevant Work ◽  
3D Printing Technique ◽  
Required Quality

AbstractAdditive manufacturing is a promising tool that has proved its value in various applications. Among its technologies, the fused filament fabrication 3D printing technique stands out with its potential to serve a wide variety of applications, ranging from simple educational purposes to industrial and medical applications. However, as many materials and composites can be utilized for this technique, the processability of these materials can be a limiting factor for producing products with the required quality and properties. Over the past few years, many researchers have attempted to better understand the melt extrusion process during 3D printing. Moreover, other research groups have focused on optimizing the process by adjusting the process parameters. These attempts were conducted using different methods, including proposing analytical models, establishing numerical models, or experimental techniques. This review highlights the most relevant work from recent years on fused filament fabrication 3D printing and discusses the future perspectives of this 3D printing technology.

Sign in / Sign up

Export Citation Format

Share Document