scholarly journals A Piezoelectric and Electromagnetic Hybrid Galloping Energy Harvester with the Magnet Embedded in the Bluff Body

Micromachines ◽  
2021 ◽  
Vol 12 (6) ◽  
pp. 626
Author(s):  
Xia Li ◽  
Cheng Bi ◽  
Zhiyuan Li ◽  
Benxue Liu ◽  
Tingting Wang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Wind Speed ◽  
Output Power ◽  
Bluff Body ◽  
Energy Harvester ◽  
Electromagnetic Energy ◽  
Piezoelectric Energy ◽  
Field Lines ◽  
Output Characteristics ◽  
Effective Output

To meet the needs of low-power microelectronic devices for on-site self-supply energy, a galloping piezoelectric–electromagnetic energy harvester (GPEEH) is proposed. It consists of a galloping piezoelectric energy harvester (GPEH) and an electromagnetic energy harvester (EEH), which is installed inside the bluff body of the GPEH. The vibration at the end of the GPEH cantilever drives the magnet to vibrate, so that electromagnetic energy can be captured by cutting off the induced magnetic field lines. The coupling structure is a two-degree-of-freedom motion, which improves the output power of the energy harvester. Based on Hamilton’s variational principle and quasi-static hypothesis, the piezoelectric–electromagnetic vibrated coupling equation is established, and the output characteristics of GPEEH are obtained by the method of numerical simulation. Using the method of numerical simulation, studies a series of parameters on the output performance. when the wind speed is 9 m/s, the effective output power of the GPEEH is compared with the classical galloping piezoelectric energy harvester (CGPEH) who is no magnet. It is found that the output power of GPEEH 121% higher than the output power of CGPEH. Finally, set up an experimental platform, and test and verify. The experimental analysis results show that the simulated output parameter curves are basically consistent with the experimental drawing curves. In addition, when the wind speed is 9 m/s, under the same parameters, the effective output power of the GPEEH is 112.5% higher than that of the CGPEH. The correctness of the model is verified.

Performance analysis of a lever piezoelectric energy harvester for roadway applications

2021 ◽  
pp. 1045389X2110014
Author(s):  
Guangya Ding ◽  
Hongjun Luo ◽  
Jun Wang ◽  
Guohui Yuan
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Open Circuit ◽  
Traffic Load ◽  
Energy Harvesters ◽  
Speed Sensor ◽  
Piezoelectric Energy ◽  
Optimal Load ◽  
Self Powered ◽  
Output Characteristics

A novel lever piezoelectric energy harvester (LPEH) was designed for installation in an actual roadway for energy harvesting. The model incorporates a lever module that amplifies the applied traffic load and transmits it to the piezoelectric ceramic. To observe the piezoelectric growth benefits of the optimized LPEH structure, the output characteristics and durability of two energy harvesters, the LPEH and a piezoelectric energy harvester (PEH) without a lever, were measured and compared by carrying out piezoelectric performance tests and traffic model experiments. Under the same loading condition, the open circuit voltages of the LPEH and PEH were 20.6 and 11.7 V, respectively, which represents a 76% voltage increase for the LPEH compared to the PEH. The output power of the LPEH was 21.51 mW at the optimal load, which was three times higher than that of the PEH (7.45 mW). The output power was linearly dependent on frequency and load, implying the potential application of the module as a self-powered speed sensor. When tested during 300,000 loading cycles, the LPEH still exhibited stable structural performance and durability.

scholarly journals Optimization of Galloping Piezoelectric Energy Harvester with V-Shaped Groove in Low Wind Speed

Energies ◽  
2019 ◽  
Vol 12 (24) ◽  
pp. 4619 ◽  
Author(s):  
Kaiyuan Zhao ◽  
Qichang Zhang ◽  
Wei Wang
Keyword(s):  
Wind Speed ◽  
Output Power ◽  
Critical Velocity ◽  
Energy Harvester ◽  
Windward Side ◽  
Flow Induced Vibration ◽  
Vibration Energy Harvester ◽  
Low Wind Speed ◽  
Local Hopf Bifurcation ◽  
Piezoelectric Energy

A square cylinder with a V-shaped groove on the windward side in the piezoelectric cantilever flow-induced vibration energy harvester (FIVEH) is presented to improve the output power of the energy harvester and reduce the critical velocity of the system, aiming at the self-powered supply of low energy consumption devices in the natural environment with low wind speed. Seven groups of galloping piezoelectric energy harvesters (GPEHs) were designed and tested in a wind tunnel by gradually changing the angle of two symmetrical sharp angles of the V-groove. The GPEH with a sharp angle of 45° was selected as the optimal energy harvester. Its output power was 61% more than the GPEH without the V-shaped groove. The more accurate mathematical model was made by using the sparse identification method to calculate the empirical parameters of fluid based on the experimental data and the theoretical model. The critical velocity of the galloping system was calculated by analyzing the local Hopf bifurcation of the model. The minimum critical velocity was 2.53 m/s smaller than the maximum critical velocity at 4.69 m/s. These results make the GPEH with a V-shaped groove (GPEH-V) more suitable to harvest wind energy efficiently in a low wind speed environment.

Numerical research on a vortex shedding induced piezoelectric-electromagnetic energy harvester

2021 ◽  
pp. 1045389X2110116
Author(s):  
Xia Li ◽  
Zhiyuan Li ◽  
Benxue Liu ◽  
Jun Zhang ◽  
Weidong Zhu
Keyword(s):  
Wind Speed ◽  
Output Power ◽  
Vortex Shedding ◽  
Energy Harvester ◽  
Hybrid Structure ◽  
Vibration Energy ◽  
Vibration Energy Harvester ◽  
Piezoelectric Energy ◽  
Speed Range ◽  
Electromechanical Coupled

To widen the operation wind speed bandwidth of a classic vortex shedding induced vibration piezoelectric energy harvester, a piezoelectric-electromagnetic hybrid energy harvester based on vortex shedding induced vibration is designed. The hybrid vortex shedding induced vibration energy harvester (HVSIVEH) includes a vortex shedding induced vibration piezoelectric energy harvester (VSIVPEH) and an electromagnetic vibration energy harvester (EVEH). The electromechanical coupled vibration model of the hybrid structure was established. By comparing the variations of the output power as a function of the wind speed of the HVSIVEH and the classic VSIVPEH, it is found that the power response curve of the HVSIVEH has two peaks. The hybrid structure can broaden the working wind speed range. The lower the requirement on the output power level, the more obvious the effect of widening the wind speed range. By the solution and analysis of the electromechanical coupled model, better values of related parameters of the HVSIVEH are obtained. The first and second peaks of the output power of the HVSIVEH show better values of 1.9 and 2.2 mW, respectively, under these parameters.

Fan-structure wind energy harvester using circular array of polyvinylidene fluoride cantilevers

2016 ◽  
Vol 28 (5) ◽  
pp. 653-662 ◽  
Author(s):  
Fengxian Bai ◽  
Guoliang Song ◽  
Weijie Dong ◽  
Lijuan Guan ◽  
Huayu Bao
Keyword(s):  
Wind Speed ◽  
Wind Energy ◽  
Output Power ◽  
Lead Zirconate Titanate ◽  
Polyvinylidene Fluoride ◽  
Energy Harvester ◽  
Lead Zirconate ◽  
Circular Array ◽  
Piezoelectric Energy ◽  
The Impact

A fan-structure piezoelectric energy harvester was proposed and tested in order to collect wind energy. Polyvinylidene fluoride was chosen due to its flexibility and longevity when compared to lead zirconate titanate. The impact-induced piezoelectric energy harvester consists of a stator and a rotor and a circular array of four cantilevers, utilize the rotor blades’ periodic impact on the free end of the cantilevers to generate oscillatory motion of cantilevers. A circular array of polyvinylidene fluoride cantilevers was fixed around the rotor in order to increase output power, save space at the same time. Static and transient characteristics of different cantilevers were investigated using finite element method and the result showed that polyvinylidene fluoride triangular cantilever performs the best in output voltage and power. Under the condition of optimal impedance and optimal overlap distance, a sum AC output power of four cantilevers without connection to each other approach to 0.75 mW was measured at the wind speed of 7 m/s when the blade number of rotor is 7 or 9. Two branches 0.27 mW DC output power was obtained when each two cantilevers in parallel connection in the case of full-wave rectification of each cantilever at the wind speed of 7 m/s.

scholarly journals Analytical Modeling of a Doubly Clamped Flexible Piezoelectric Energy Harvester with Axial Excitation and Its Experimental Characterization

Sensors ◽  
2021 ◽  
Vol 21 (11) ◽  
pp. 3861
Author(s):  
Jie Mei ◽  
Qiong Fan ◽  
Lijie Li ◽  
Dingfang Chen ◽  
Lin Xu ◽  
...  
Keyword(s):  
Output Power ◽  
Power Output ◽  
Output Voltage ◽  
Energy Harvester ◽  
Load Resistance ◽  
Engineering Practice ◽  
Maximum Output ◽  
Widespread Application ◽  
Piezoelectric Energy ◽  
Axial Excitation

With the rapid development of wearable electronics, novel power solutions are required to adapt to flexible surfaces for widespread applications, thus flexible energy harvesters have been extensively studied for their flexibility and stretchability. However, poor power output and insufficient sensitivity to environmental changes limit its widespread application in engineering practice. A doubly clamped flexible piezoelectric energy harvester (FPEH) with axial excitation is therefore proposed for higher power output in a low-frequency vibration environment. Combining the Euler–Bernoulli beam theory and the D’Alembert principle, the differential dynamic equation of the doubly clamped energy harvester is derived, in which the excitation mode of axial load with pre-deformation is considered. A numerical solution of voltage amplitude and average power is obtained using the Rayleigh–Ritz method. Output power of 22.5 μW at 27.1 Hz, with the optimal load resistance being 1 MΩ, is determined by the frequency sweeping analysis. In order to power electronic devices, the converted alternating electric energy should be rectified into direct current energy. By connecting to the MDA2500 standard rectified electric bridge, a rectified DC output voltage across the 1 MΩ load resistor is characterized to be 2.39 V. For further validation of the mechanical-electrical dynamical model of the doubly clamped flexible piezoelectric energy harvester, its output performances, including both its frequency response and resistance load matching performances, are experimentally characterized. From the experimental results, the maximum output power is 1.38 μW, with a load resistance of 5.7 MΩ at 27 Hz, and the rectified DC output voltage reaches 1.84 V, which shows coincidence with simulation results and is proved to be sufficient for powering LED electronics.

scholarly journals Power Density Improvement of Piezoelectric Energy Harvesters via a Novel Hybridization Scheme with Electromagnetic Transduction

Micromachines ◽  
2021 ◽  
Vol 12 (7) ◽  
pp. 803
Author(s):  
Zhongjie Li ◽  
Chuanfu Xin ◽  
Yan Peng ◽  
Min Wang ◽  
Jun Luo ◽  
...  
Keyword(s):  
Power Density ◽  
Output Power ◽  
Energy Harvester ◽  
Hybrid Energy ◽  
Energy Harvesters ◽  
Piezoelectric Patch ◽  
Piezoelectric Energy ◽  
Electromagnetic Transduction ◽  
Self Powered ◽  
Power Densities

A novel hybridization scheme is proposed with electromagnetic transduction to improve the power density of piezoelectric energy harvester (PEH) in this paper. Based on the basic cantilever piezoelectric energy harvester (BC-PEH) composed of a mass block, a piezoelectric patch, and a cantilever beam, we replaced the mass block by a magnet array and added a coil array to form the hybrid energy harvester. To enhance the output power of the electromagnetic energy harvester (EMEH), we utilized an alternating magnet array. Then, to compare the power density of the hybrid harvester and BC-PEH, the experiments of output power were conducted. According to the experimental results, the power densities of the hybrid harvester and BC-PEH are, respectively, 3.53 mW/cm3 and 5.14 μW/cm3 under the conditions of 18.6 Hz and 0.3 g. Therefore, the power density of the hybrid harvester is 686 times as high as that of the BC-PEH, which verified the power density improvement of PEH via a hybridization scheme with EMEH. Additionally, the hybrid harvester exhibits better performance for charging capacitors, such as charging a 2.2 mF capacitor to 8 V within 17 s. It is of great significance to further develop self-powered devices.

scholarly journals Study of the Properties of a Hybrid Piezoelectric and Electromagnetic Energy Harvester for a Civil Engineering Low-Frequency Sloshing Environment

Energies ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 391
Author(s):  
Nan Wu ◽  
Yuncheng He ◽  
Jiyang Fu ◽  
Peng Liao
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Civil Engineering ◽  
Maximum Output Power ◽  
Low Frequency ◽  
Electromagnetic Energy ◽  
Maximum Output ◽  
Piezoelectric Film ◽  
Hybrid Energy ◽  
Level Height

In this paper a novel hybrid piezoelectric and electromagnetic energy harvester for civil engineering low-frequency sloshing environment is reported. The architecture, fabrication and characterization of the harvester are discussed. The hybrid energy harvester is composed of a permanent magnet, copper coil, and PVDF(polyvinylidene difluoride) piezoelectric film, and the upper U-tube device containing a cylindrical fluid barrier is connected to the foundation support plate by a hinge and spring. The two primary means of energy collection were through the vortex street, which alternately impacted the PVDF piezoelectric film through fluid shedding, and the electromotive force (EMF) induced by changes in the magnetic field position in the conducting coil. Experimentally, the maximum output power of the piezoelectric transformer of the hybrid energy harvester was 2.47 μW (circuit load 270 kΩ; liquid level height 80 mm); and the maximum output power of the electromagnetic generator was 2.72 μW (circuit load 470 kΩ; liquid level height 60 mm). The low-frequency sloshing energy collected by this energy harvester can drive microsensors for civil engineering monitoring.

Modeling and Experimental Validations of a Piezoelectric Energy Harvester Under Combined Galloping and Base Excitations

2014 ◽  
Author(s):  
Amin Bibo ◽  
Abdessattar Abdelkefi ◽  
Mohammed F. Daqaq
Keyword(s):  
Bluff Body ◽  
Energy Harvester ◽  
Constitutive Relations ◽  
Excitation Frequency ◽  
Primary Resonance ◽  
Beam Theory ◽  
Excitation Amplitude ◽  
The Body ◽  
Base Excitation ◽  
Piezoelectric Energy

This paper develops an experimentally validated model of a piezoelectric energy harvester under combined aeroelastic-galloping and base excitations. To that end, an energy harvester consisting of a thin piezoelectric cantilever beam subjected to vibratory base excitation is considered. To permit galloping excitation, a bluff body is rigidly attached at the free end such that a net aerodynamic lift is generated as the incoming airflow separates on both sides of the body giving rise to limit cycle oscillations when the flow velocity exceeds a critical value. A nonlinear electromechanical distributed-parameter model of the harvester under the combined excitation is derived using the energy approach and by adopting the nonlinear Euler-Bernoulli beam theory, linear constitutive relations for the piezoelectric transduction, and the quasi-steady assumption for the aerodynamic loading. The partial differential equations of the system are discretized and a reduced-order-model is obtained. The mathematical model is validated by conducting a series of experiments with different loading conditions represented by wind speed, base excitation amplitude, and excitation frequency around the primary resonance.

scholarly journals Study on the Efficiency and Dynamic Characteristics of an Energy Harvester Based on Flexible Structure Galloping

Energies ◽  
2021 ◽  
Vol 14 (20) ◽  
pp. 6548
Author(s):  
Peng Liao ◽  
Jiyang Fu ◽  
Wenyong Ma ◽  
Yuan Cai ◽  
Yuncheng He
Keyword(s):  
Numerical Simulation ◽  
Wind Speed ◽  
Physical Model ◽  
Energy Harvester ◽  
High Efficiency ◽  
Lateral Displacement ◽  
Maximum Output Power ◽  
Flexible Structure ◽  
Maximum Output ◽  
Cfd Numerical Simulation

According to the engineering phenomenon of the galloping of ice-coated transmission lines at certain wind speeds, this paper proposes a novel type of energy harvester based on the galloping of a flexible structure. It uses the tension generated by the galloping structure to cause periodic strain on the piezoelectric cantilever beam, which is highly efficient for converting wind energy into electricity. On this basis, a physical model of fluid–structure interaction is established, and the Reynolds-averaged Navier–Stokes equation and SST K -ω turbulent model based on ANSYS Fluent are used to carry out a two-dimensional steady computational fluid dynamics (CFD) numerical simulation. First, the CFD technology under different grid densities and time steps is verified. CFD numerical simulation technology is used to simulate the physical model of the energy harvester, and the effect of wind speed on the lateral displacement and aerodynamic force of the flexible structure is analyzed. In addition, this paper also carries out a parameterized study on the influence of the harvester’s behavior, through the wind tunnel test, focusing on the voltage and electric power output efficiency. The harvester has a maximum output power of 119.7 μW/mm3 at the optimal resistance value of 200 KΩ at a wind speed of 10 m/s. The research results provide certain guidance for the design of a high-efficiency harvester with a square aerodynamic shape and a flexible bluff body.

Sign in / Sign up

Export Citation Format

Share Document