scholarly journals Analysis of Stiffness Effect on Valve Behavior of a Reciprocating Pump Operated by Piezoelectric Elements

Micromachines ◽  
2020 ◽  
Vol 11 (10) ◽  
pp. 894
Author(s):  
Jangmi Woo ◽  
Dong Kee Sohn ◽  
Han Seo Ko
Keyword(s):  
Flow Rate ◽  
Operating Frequency ◽  
Piezo Actuator ◽  
Driving Frequency ◽  
Inlet Valve ◽  
Pump Performance ◽  
Piezoelectric Elements ◽  
Outlet Valve ◽  
Valve Opening ◽  
Reciprocating Pump

This study analyzed the characteristics of a small reciprocating pump with a cantilever valve driven by a piezo actuator. Three types of valves were fabricated to investigate the effect of the valve stiffness on the pump performance and to measure the variation in the flow rate according to the frequency. The flow rate increased with the driving frequency until a certain frequency was reached, and then it started to decrease. The rise in the pressure of the pump was found to increase as the stiffness decreased. The pump performance could be clearly distinguished according to the stiffness of the valve. The observation of the valve movements revealed that the valve opening time did not change regardless of the operating frequency, but it changed with the valve stiffness. The delay in time for the outlet valve increased significantly with an increase in the frequency. It seems that the overlap of the opening time of the inlet valve and the outlet valve plays an important role in pump performance. Therefore, it is advisable to use different designs for the inlet and outlet valves, where the shape and stiffness of the valve are adjusted.

Experimental Study on Small Hydraulic Pump Using Visualization Technique

2019 ◽  
Author(s):  
Jangmi Woo ◽  
Yeonghyeon Gim ◽  
Dong Kee Sohn ◽  
Han Seo Ko
Keyword(s):  
Flow Rate ◽  
Smart Materials ◽  
Maximum Flow ◽  
Sine Wave ◽  
Piezo Actuator ◽  
Driving Frequency ◽  
Hydraulic Pump ◽  
Recent Developments ◽  
Reed Valve ◽  
Critical Components

Abstract Recent developments of smart materials such as piezo devices have been applied to small hydraulic pumps, enabling to meet various demands. For the compact pump, the valves are critical components in the aspect of fluid dynamics. In this study, the flow inside the reed valve port driven by the piezo actuator was experimentally observed. When a sine wave with a driving frequency of 90 Hz was applied, the maximum flow rate could be obtained. It was found that the developed flow opposite to the outlet direction at the root portion of the valve prevented further increase of the flow rate according to the operating frequency.

The Performance Simulation of One-Way Inlet Valve of Reflux Scavenging Free Piston Engine

2013 ◽  
Vol 694-697 ◽  
pp. 582-587
Author(s):  
Zhen Xin Li ◽  
Zhao Cheng Yuan ◽  
Jia Yi Ma ◽  
Shi Yu Li
Keyword(s):  
Flow Rate ◽  
Spring Constant ◽  
Air Flow Rate ◽  
Inlet Valve ◽  
Free Piston ◽  
Performance Simulation ◽  
Bottom Dead Center ◽  
Free Piston Engine ◽  
Opening And Closing ◽  
Stroke Engine

The performance of one-way inlet valve directly impacts the effect of the reflux scavenging two-stroke engine intake. It’s discovered that the intake air flow rate, the weight of valve and the spring constant have the greatest impact on the opening, closing and the lift change of one-way inlet valve, by simulating the movement of piston and valve using CFD software. The greater the flow rate, the smaller the weight of valve, or the smaller the spring constant, then the faster the opening of valve. Meanwhile, in order to ensure that the valve quickly returns, the bigger of spring constant is the better. The phases of opening and closing of valve lag fall behind the phases of piston getting to bottom dead center (BDC) and top dead center (TDC).

EXPERIMENTAL INVESTIGATION OF ENHANCEMENT IN EFFICIENCY OF CENTRIFUGAL PUMP BY REDUCTION IN CAVITATION OF PUMP

2021 ◽  
Vol 5 (10) ◽  
Author(s):  
Gaffar G. Momin
Keyword(s):  
Experimental Investigation ◽  
Centrifugal Pump ◽  
Flow Rate ◽  
Rate Control ◽  
Flowing Liquid ◽  
Discharge Flow ◽  
Pump Performance ◽  
Cavitation Phenomenon ◽  
Discharge Flow Rate ◽  
Flow Rate Control

Cavitation phenomenon is basically a process formation of bubbles of a flowing liquid in a region where the pressure of the liquid falls below its vapour pressure and it is the most challenging fluid flow abnormalities leading to detrimental effects on both the centrifugal pump discharge characteristics as well as physical characteristics. In this low pressure zones are the first victims of cavitation. Due to cavitation pitting of impeller occurs and wear of internal walls of pumps occurs due to which there is creation of vibrations and noize are there. Due to this there is bad performance of centrifugal pump is there. Firstly, description of the centrifugal pump with its various parts are described after that pump characteristics and its important parameters are presented and discussed. Passive discharge (flow rate) control methods are utilized for improvement of flow rate and mechanical and volumetric and overall efficiency of the pump. Mechanical engineers is considering an important phenomenon which is known as Cavitation due to which there is decrease in centrifugal pump performance. There is also effect on head of the pump which is getting reduced due to cavitation phenomenon. In present experimental investigation the cavitation phenomenon is studied by starting and running the pump at various discharges and cavitating conditions of the centrifugal pump. Passive discharge (flow rate) control is realized using three different impeller blade leading edge angles namely 9.5 degrees, 16.5 degrees .and 22.5 degrees for reduction in the cavitation and increase the of the centrifugal pump performance at different applications namely, domestic, industrial applications of the centrifugal pump.

3D Flow Simulation of a Twin-Screw Pump for the Analysis of Gap Flow Characteristics

2021 ◽  
Author(s):  
Ali Hassannejadmoghaddam ◽  
Boris Kutschelis ◽  
Frank Holz ◽  
Tomas Börjesson ◽  
Romuald Skoda
Keyword(s):  
Flow Rate ◽  
Volume Flow Rate ◽  
Overset Grid ◽  
3D Flow ◽  
Screw Pump ◽  
Pump Performance ◽  
Gap Flow ◽  
Wide Range ◽  
Twin Screw ◽  
Pump Head

Abstract Unsteady 3D flow simulations on a twin-screw pump are performed for an assessment of the radial, circumferential and flank gap flow effect on the pump performance. By means of the overset grid technique rigid computational grids around the counter-rotating spindles yield a high cell quality and a high spatial resolution of the gap backflow down to the viscous sublayer in terms of y^+ < 1 . An optimization of the hole-cutting process is performed on a generic gap flow and transferred to the complex moving gaps in the pump. Grid independence is ensured, and conservation properties of the overset grid interpolation technique are assessed. Simulation results are validated against measured pump characteristics. Pump performance in terms of pressure build-up along the flow path through the spindles and volume flow rate is presented for a wide range of spindle speed and pump head. Flow rate fluctuations are found to depend on head but hardly on speed. By a profound assessment of the respective radial, circumferential and flank gap contribution to the total backflow, the importance of the most complex flank gap is pointed out. Backflow rate characteristics in dependence on the pump head and the pump speed are presented.

The Effect of Air Injection Method on the Airlift Pump Performance

2012 ◽  
Vol 134 (11) ◽  
Author(s):  
Dong Hu ◽  
Chuan-Lin Tang ◽  
Shu-Peng Cai ◽  
Feng-Hua Zhang
Keyword(s):  
Flow Rate ◽  
Volume Flow Rate ◽  
Low Cost ◽  
Air Injection ◽  
Water Volume ◽  
Pump Design ◽  
Pump Performance ◽  
Dimensionless Equation ◽  
Measurement Results ◽  
Injection Methods

With simple structure, excellent reliability, low cost, no restriction at depth of water, and easy control and operation, airlift pumps have special advantage in borehole hydraulic jet mining, river dredging and deep sea mining. To clarify the mechanism and process of action of air injection methods on air lift performance, and to enhance lifting capacity, the pump performance of a small airlift system in transporting river sands is investigated experimentally in the present study. The results are as the follows. The influences of air exit ports on water volume flow rate, mass flow rate of solids and lifting efficiency are studied and found to be very low when the number of air exit ports exceeds 3. The pump design show best pumping capability for water and solids at higher air flow rates, but the lifting efficiency is then very low. In addition, a dimensionless equation which describes the flows in the pipe is presented based on the Bernoulli equation, and compared with measurement results in the dimensionless form, which are nearly in good agreement with each other for all the arrangements of air exit ports and are basically contained within ±18% of the theoretical curve. The results are important for understanding the mechanism of airlift pumps and enriching multiphase flow theory.

scholarly journals NUMERICAL MODELLING OF OSCILLATING FLOW FOR ENERGY HARVESTING

2021 ◽  
Vol 2021 (6) ◽  
pp. 5360-5365
Author(s):  
TOMAS BLEJCHAR ◽  
◽  
SYLVA DRABKOVA ◽  
VACLAV JANUS ◽  
◽  
...  
Keyword(s):  
Flow Rate ◽  
Volume Flow Rate ◽  
Electrical Energy ◽  
Maximum Energy ◽  
Oscillating Flow ◽  
Cfd Simulations ◽  
Fluidic Oscillator ◽  
Microelectronic Devices ◽  
Piezoelectric Elements ◽  
New Generation

The energy efficiency of systems, equipment, and sensors is nowadays intensively studied. The new generation of microelectronic sensors is very sophisticated and the energy consumption is in the microwatts range. The energy to power the microelectronic devices can be harvested from oscillating flow in small size channels and so replaceable batteries could be eliminated. Piezoelectric elements can convert energy from oscillation to electrical energy. This paper focuses on the simulation of periodic flow in the fluidic oscillator. CFD simulations were performed for several values of the flow rate. Experimental measurement was carried out under the same conditions as the CFD experiment. The main monitored and evaluated parameters were volume flow rate and pressure loss. Fluid oscillations were analysed based on CFD simulations and the theoretical maximum energy available for the deformation of piezoelectric elements and transformable into electrical energy was evaluated.

An experimental performance comparison of Newtonian and non-Newtonian fluids on a centrifugal blood pump

2022 ◽  
pp. 095441192110576
Author(s):  
Ahmet Onder ◽  
Rafet Yapici ◽  
Omer Incebay
Keyword(s):  
Flow Rate ◽  
Rotational Speed ◽  
Performance Test ◽  
Newtonian Fluids ◽  
Friction Reduction ◽  
Blood Pump ◽  
Actual Performance ◽  
Centrifugal Blood Pump ◽  
Working Fluids ◽  
Pump Performance

The use of substitute fluid with similar rheological properties instead of blood is important due to ethical concerns and high blood volume consumption in pump performance test before clinical applications. The performance of a centrifugal blood pump with hydrodynamic journal bearing is experimentally tested using Newtonian 40% aqueous glycerin solution (GS) and non-Newtonian aqueous xanthan gum solution of 600 ppm (XGS) as working fluids. Experiments are performed at four different rotational speeds which are 2700, 3000, 3300, and 3600 rpm; experiments using GS reach between 8.5% and 37.2% higher head curve than experiments using the XGS for every rotational speed. It was observed that as the rotational speed and flow rate increase, the head curve difference between GS and XGS decreases. This result can be attributed to the friction reduction effect when using XGS in experiments at high rotation speed and high flow rate. Moreover, due to different fluid viscosities, differences in hydraulic efficiency were observed for both fluids. This study reveals that the use of Newtonian fluids as working fluids is not sufficient to determine the actual performance of a blood pump, and the performance effects of non-Newtonian fluids are remarkably important in pump performance optimizations.

Reciprocating compressor valve damage estimation under varying speeds through the acoustic emission technique

2019 ◽  
Vol 10 (5) ◽  
pp. 621-633
Author(s):  
Hoi-Yin Sim ◽  
Rahizar Ramli ◽  
Ahmad Saifizul
Keyword(s):  
Acoustic Emission ◽  
Regression Analysis ◽  
Flow Rate ◽  
Reciprocating Compressor ◽  
Damage Estimation ◽  
Content Type ◽  
Air Compressor ◽  
Ae Signal ◽  
Valve Opening ◽  
Ae Signals

Purpose The purpose of this paper is to examine the effect of reciprocating compressor speeds and valve conditions on the roor-mean-square (RMS) value of burst acoustic emission (AE) signals associated with the physical motion of valves. The study attempts to explore the potential of AE signal in the estimation of valve damage under varying compressor speeds. Design/methodology/approach This study involves the acquisition of AE signal, valve flow rate, pressure and temperature at the suction valve of an air compressor with speed varrying from 450 to 800 rpm. The AE signals correspond to one compressor cycle obtained from two simulated valve damage conditions, namely, the single leak and double leak conditions are compared to those of the normal valve plate. To examine the effects of valve conditions and speeds on AE RMS values, two-way analysis of variance (ANOVA) is conducted. Finally, regression analysis is performed to investigate the relationship of AE RMS with the speed and valve flow rate for different valve conditions. Findings The results showed that AE RMS values computed from suction valve opening (SVO), suction valve closing (SVC) and discharge valve opening (DVO) events are significantly affected by both valve conditions and speeds. The AE RMS value computed from SVO event showed high linear correlation with speed compared to SVC and DVO events for all valve damage conditions. As this study is conducted at a compressor running at freeload, increasing speed of compressor also results in the increment of flow rate. Thus, the valve flow rate can also be empirically derived from the AE RMS value through the regression method, enabling a better estimation of valve damages. Research limitations/implications The experimental test rig of this study is confined to a small pressure ratio range of 1.38–2.03 (free-loading condition). Besides, the air compressor is assumed to be operated at a constant speed. Originality/value This study employed the statistical methods namely the ANOVA and regression analysis for valve damage estimation at varying compressor speeds. It can enable a plant personnel to make a better prediction on the loss of compressor efficiency and help them to justify the time for valve replacement in future.

scholarly journals Comparison of Swing and Tilting Check Valves Flowing Compressible Fluids

Micromachines ◽  
2020 ◽  
Vol 11 (8) ◽  
pp. 758
Author(s):  
Zhi-xin Gao ◽  
Ping Liu ◽  
Yang Yue ◽  
Jun-ye Li ◽  
Hui Wu
Keyword(s):  
Mach Number ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Check Valve ◽  
Small Mass ◽  
Working Fluid ◽  
Valve Disc ◽  
Valve Opening ◽  
The Difference

Although check valves have attracted a lot of attention, work has rarely been completed done when there is a compressible working fluid. In this paper, the swing check valve and the tilting check valve flowing high-temperature compressible water vapor are compared. The maximum Mach number under small valve openings, the dynamic opening time, and the hydrodynamic moment acting on the valve disc are chosen to evaluate the difference between the two types of check valves. Results show that the maximum Mach number increases with the decrease in the valve opening and the increase in the mass flow rate, and the Mach number and the pressure difference in the tilting check valve are higher. In the swing check valve, the hydrodynamic moment is higher and the valve opening time is shorter. Furthermore, the valve disc is more stable for the swing check valve, and there is a periodical oscillation of the valve disc in the tilting check valve under a small mass flow rate.

Sign in / Sign up

Export Citation Format

Share Document