scholarly journals The Impact of Hydrogen on Mechanical Properties; A New In Situ Nanoindentation Testing Method

Micromachines ◽  
2019 ◽  
Vol 10 (2) ◽  
pp. 114 ◽  
Author(s):  
Christian Müller ◽  
Mohammad Zamanzade ◽  
Christian Motz
Keyword(s):  
Mechanical Properties ◽  
Activation Energy ◽  
Elastic Modulus ◽  
Dislocation Nucleation ◽  
Coarse Grained ◽  
Testing Method ◽  
Nanomechanical Testing ◽  
Nanoindentation Testing ◽  
The Impact

We have designed a new method for electrochemical hydrogen charging which allows us to charge very thin coarse-grained specimens from the bottom and perform nanomechanical testing on the top. As the average grain diameter is larger than the thickness of the sample, this setup allows us to efficiently evaluate the mechanical properties of multiple single crystals with similar electrochemical conditions. Another important advantage is that the top surface is not affected by corrosion by the electrolyte. The nanoindentation results show that hydrogen reduces the activation energy for homogenous dislocation nucleation by approximately 15–20% in a (001) grain. The elastic modulus also was observed to be reduced by the same amount. The hardness increased by approximately 4%, as determined by load-displacement curves and residual imprint analysis.

scholarly journals Numerical Studies of the Effects of Water Capsules on Self-Healing Efficiency and Mechanical Properties in Cementitious Materials

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Haoliang Huang ◽  
Guang Ye
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Cementitious Materials ◽  
Self Healing ◽  
Negative Effects ◽  
Numerical Studies ◽  
Healing Efficiency ◽  
The Impact ◽  
Positive Effect

In this research, self-healing due to further hydration of unhydrated cement particles is taken as an example for investigating the effects of capsules on the self-healing efficiency and mechanical properties of cementitious materials. The efficiency of supply of water by using capsules as a function of capsule dosages and sizes was determined numerically. By knowing the amount of water supplied via capsules, the efficiency of self-healing due to further hydration of unhydrated cement was quantified. In addition, the impact of capsules on mechanical properties was investigated numerically. The amount of released water increases with the dosage of capsules at different slops as the size of capsules varies. Concerning the best efficiency of self-healing, the optimizing size of capsules is 6.5 mm for capsule dosages of 3%, 5%, and 7%, respectively. Both elastic modulus and tensile strength of cementitious materials decrease with the increase of capsule. The decreasing tendency of tensile strength is larger than that of elastic modulus. However, it was found that the increase of positive effect (the capacity of inducing self-healing) of capsules is larger than that of negative effects (decreasing mechanical properties) when the dosage of capsules increases.

Test Methods for Mechanical Properties of Structural Adhesives

2010 ◽  
Vol 97-101 ◽  
pp. 814-817 ◽  
Author(s):  
Jun Deng
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Shear Strength ◽  
Elastic Modulus ◽  
Butt Joint ◽  
Test Methods ◽  
Joint Specimen ◽  
Lap Shear ◽  
Better Than

One of the greatest drawbacks to predicting the behaviour of bonded joints has been the lack of reliable data on the mechanical properties of adhesives. In this study, methods for determining mechanical properties of structural adhesive were discussed. The Young’s modulus, Poisson’s ratio and tensile strength of the adhesive were tested by dogbone specimens (bulk form) and butt joint specimens (in situ form). The shear modulus and shear strength were test by V-notched specimens (bulk form) and thick adherend lap-shear (TALS) joint specimens (in situ form). The test results show that the elastic modulus provided by the manufacturer is too low, the dogbone specimen is better than the butt joint specimen to test the tensile strength and elastic modulus and the TALS joint specimen is better than the V-notched specimen to test the shear strength.

Measurement of Cement in Situ Stresses and Mechanical Properties Without Cooling or Depressurization

2021 ◽  
Author(s):  
Meng Meng ◽  
Luke Frash ◽  
James Carey ◽  
Wenfeng Li ◽  
Nathan Welch ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Property ◽  
Elastic Modulus ◽  
Poisson’S Ratio ◽  
Axial Stress ◽  
Triaxial Compression ◽  
In Situ Measurement ◽  
Poisson's Ratio ◽  
Ambient Conditions

Abstract Accurate characterization of oilwell cement mechanical properties is a prerequisite for maintaining long-term wellbore integrity. The drawback of the most widely used technique is unable to measure the mechanical property under in situ curing environment. We developed a high pressure and high temperature vessel that can hydrate cement under downhole conditions and directly measure its elastic modulus and Poisson's ratio at any interested time point without cooling or depressurization. The equipment has been validated by using water and a reasonable bulk modulus of 2.37 GPa was captured. Neat Class G cement was hydrated in this equipment for seven days under axial stress of 40 MPa, and an in situ measurement in the elastic range shows elastic modulus of 37.3 GPa and Poisson's ratio of 0.15. After that, the specimen was taken out from the vessel, and setted up in the triaxial compression platform. Under a similar confining pressure condition, elastic modulus was 23.6 GPa and Possion's ratio was 0.26. We also measured the properties of cement with the same batch of the slurry but cured under ambient conditions. The elastic modulus was 1.63 GPa, and Poisson's ratio was 0.085. Therefore, we found that the curing condition is significant to cement mechanical property, and the traditional cooling or depressurization method could provide mechanical properties that were quite different (50% difference) from the in situ measurement.

scholarly journals Effect of Cold Drawing on Mechanical Properties of Biodegradable Fibers

2017 ◽  
Vol 15 (1) ◽  
pp. 70-76 ◽  
Author(s):  
Francesco Paolo La Mantia ◽  
Manuela Ceraulo ◽  
Maria Chiara Mistretta ◽  
Marco Morreale
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Biodegradable Polymers ◽  
Biodegradable Polymer ◽  
Cold Drawing ◽  
Thermal Characterization ◽  
Systematic Investigation ◽  
Thermomechanical Properties ◽  
Polymer Systems ◽  
The Impact

Purpose Biodegradable polymers are currently gaining importance in several fields, because they allow mitigation of the impact on the environment related to disposal of traditional, nonbiodegradable polymers, as well as reducing the utilization of oil-based sources (when they also come from renewable resources). Fibers made of biodegradable polymers are of particular interest, though, it is not easy to obtain polymer fibers with suitable mechanical properties and to tailor these to the specific application. The main ways to tailor the mechanical properties of a given biodegradable polymer fiber are based on crystallinity and orientation control. However, crystallinity can only marginally be modified during processing, while orientation can be controlled, either during hot drawing or cold stretching. In this paper, a systematic investigation of the influence of cold stretching on the mechanical and thermomechanical properties of fibers prepared from different biodegradable polymer systems was carried out. Methods Rheological and thermal characterization helped in interpreting the orientation mechanisms, also on the basis of the molecular structure of the polymer systems. Results and conclusions It was found that cold drawing strongly improved the elastic modulus, tensile strength and thermomechanical resistance of the fibers, in comparison with hot-spun fibers. The elastic modulus showed higher increment rates in the biodegradable systems upon increasing the draw ratio.

Effects of microcrystalline cellulose on the mechanical properties of low-density polyethylene composites

2018 ◽  
Vol 32 (3) ◽  
pp. 297-311 ◽  
Author(s):  
Yousef Ahmad Mubarak ◽  
Raghda Talal Abdulsamad
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Impact Strength ◽  
Tensile Properties ◽  
Microcrystalline Cellulose ◽  
Weight Fraction ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Ldpe Composites ◽  
The Impact

This work was intended to provide an understanding of the effect of microcrystalline cellulose (MCC) on the mechanical properties of low-density polyethylene (LDPE). The impact resistance and the tensile properties of low-density LDPE/MCC composites were investigated. The weight fraction of MCC was varied at (0, 0.5, 1, 2.5, 5, 10, 20, and 30 wt%). The obtained blends were then used to prepare the required tensile and impact testing samples by hot compression molding technique. It has been found that MCC has a strong influence on the mechanical properties of LDPE. At a low MCC weight fraction, there was a little improvement in the ultimate strength, fracture stress, and elongation at break, but at a high MCC weight fraction, the tensile properties were deteriorated and reduced significantly. The addition of 1 wt% MCC to LDPE enhanced the mentioned properties by 10, 25, and 6%, respectively. While at 30 wt% MCC, these properties were lowered by 36, 25, and 96%. The elastic modulus of LDPE composites was improved on all MCC weight fractions used in the study, at 20 wt% MCC, an increase in the elastic modulus by 12 folds was achieved. On the other hand and compared with the impact strength of pure LDPE, the addition of MCC particles enhanced the impact strength, the highest value obtained was for LDPE composites filled with 10 wt% MCC where the impact strength enhanced by two folds.

scholarly journals Effects of Phase Morphology on Mechanical Properties: Oriented/Unoriented PP Crystal Combination with Spherical/Microfibrillar PET Phase

Polymers ◽  
2019 ◽  
Vol 11 (2) ◽  
pp. 248 ◽  
Author(s):  
Dashan Mi ◽  
Yingxiong Wang ◽  
Maja Kuzmanovic ◽  
Laurens Delva ◽  
Yixin Jiang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Ethylene Terephthalate ◽  
Phase Morphology ◽  
Mechanical Recycling ◽  
Immiscible Blends ◽  
Poly Ethylene Terephthalate ◽  
Poly Ethylene ◽  
The Impact

In situ microfibrillation and multiflow vibrate injection molding (MFVIM) technologies were combined to control the phase morphology of blended polypropylene (PP) and poly(ethylene terephthalate) (PET), wherein PP is the majority phase. Four kinds of phase structures were formed using different processing methods. As the PET content changes, the best choice of phase structure also changes. When the PP matrix is unoriented, oriented microfibrillar PET can increase the mechanical properties at an appropriate PET content. However, if the PP matrix is an oriented structure (shish-kebab), only the use of unoriented spherical PET can significantly improve the impact strength. Besides this, the compatibilizer polyolefin grafted maleic anhydride (POE-g-MA) can cover the PET in either spherical or microfibrillar shape to form a core–shell structure, which tends to improve both the yield and impact strength. We focused on the influence of all composing aspects—fibrillation of the dispersed PET, PP matrix crystalline morphology, and compatibilized interface—on the mechanical properties of PP/PET blends as well as potential synergies between these components. Overall, we provided a theoretical basis for the mechanical recycling of immiscible blends.

The Effect of Solid Solution Impurities on Dislocation Nucleation in a (001) Mo – 1.5 at.% Ir Single Crystal

2010 ◽  
Vol 662 ◽  
pp. 85-93
Author(s):  
Sergey Dub ◽  
Igor Zasimchuk ◽  
Leonid Matvienko
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Shear Stress ◽  
Elastic Modulus ◽  
Single Crystal ◽  
Single Crystals ◽  
Free Volume ◽  
Dislocation Nucleation ◽  
Initial Portion ◽  
G 12

Mechanical properties of (001) Mo and (001) Mo – 1.5 at.% Ir single crystals have been studied by nanoindentation. It has been found that the iridium addition to molybdenum leads to an increase in both hardness and elastic modulus. An abrupt elasto-plastic transition (pop-in) at a depth of about 20 - 40 nm caused by dislocation nucleation in previously dislocation-free volume has been observed in the initial portion of the loading curve. It has shown that the Ir addition essentially affects the dislocation nucleation. Mean shear stress required for the dislocation nucleation increased from 10.8 GPa (G/12) for a Mo single crystal to 18.2 GPa (G/8) for the Mo – 1.5 at% Ir solid solution. Thus, the Ir solution in a Mo single crystal affects not only the resistance to the motion of dislocations (hardness) but the nucleation of them as well. The latter is likely to occur as a result of an increase in the structure perfection of the Mo – 1.5 at% Ir solid solution as compared to the pure Mo single crystal.

Length Scale Effects in Materials Deformation of Nano and Microscale Au Structures

2009 ◽  
Author(s):  
Jie Lian ◽  
Junlan Wang
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Size Effect ◽  
Sample Size ◽  
Atomistic Simulation ◽  
Scale Effects ◽  
Elastic Recovery ◽  
Boundary Effect ◽  
Dislocation Nucleation ◽  
Atomistic Simulations

In this study, intrinsic size effect — strong size dependence of mechanical properties — in materials deformation was investigated by performing atomistic simulation of compression on Au (114) pyramids. Sample boundary effect — inaccurate measurement of mechanical properties when sample size is comparable to the indent size — in nanoindentation was also investigated by performing experiments and atomistic simulations of nanoindentation into nano- and micro-scale Au pillars and bulk Au (001) surfaces. For intrinsic size effect, dislocation nucleation and motions that contribute to size effect were analyzed for studying the materials deformation mechanisms. For sample boundary effect, in both experiments and atomistic simulation, the elastic modulus decreases with increasing indent size over sample size ratio. Significantly different dislocation motions contribute to the lower value of the elastic modulus measured in the pillar indentation. The presence of the free surface would allow the dislocations to annihilate, causing a higher elastic recovery during the unloading of pillar indentation.

scholarly journals Effect of cigarette smoking on nitric oxide, structural, and mechanical properties of mouse arteries

2006 ◽  
Vol 291 (5) ◽  
pp. H2354-H2361 ◽  
Author(s):  
X. Guo ◽  
M. J. Oldham ◽  
M. T. Kleinman ◽  
R. F. Phalen ◽  
G. S. Kassab
Keyword(s):  
Nitric Oxide ◽  
Mechanical Properties ◽  
Elastic Modulus ◽  
Cigarette Smoking ◽  
Coronary Arteries ◽  
Short And Long Term ◽  
By Products ◽  
Enos Protein

Cigarette smoking (CS) is a major risk factor for vascular disease. The aim of this study was to quantitatively assess the influence of CS on mouse arteries. We studied the effect of short-term (6 wk) and long-term (16 wk) CS exposure on structural and mechanical properties of coronary arteries compared with that of control mice. We also examined the reversibility of the deleterious effects of CS on structural [e.g., wall thickness (WT)], mechanical (e.g., stiffness), and biochemical [e.g., nitric oxide (NO) by-products] properties with the cessation of CS. The left and right coronary arteries were cannulated in situ and mechanically distended. The stress, strain, elastic modulus, and WT of coronary arteries were determined. Western blot analysis was used to analyze endothelial NO synthase (eNOS) in the femoral and carotid arteries of the same mice, and NO by-products were determined by measuring the levels of nitrite. Our results show that the mean arterial pressure was increased by CS. Furthermore, CS significantly increased the elastic modulus, decreased stress and strain, and increased the WT and WT-to-radius ratio compared with those of control mice. The reduction of eNOS protein expression was found only after long-term CS exposure. Moreover, the NO metabolite was markedly decreased in CS mice after short- and long-term exposure of CS. These findings suggest that 16 wk of CS exposure can cause an irreversible deterioration of structural and elastic properties of mouse coronary arteries. The decrease in endothelium-derived NO in CS mice was seen to significantly correlate with the remodeling of arterial wall.

Grain Growth and Mechanical Properties of Nanograined Bulk Fe-25Ni Alloy

2005 ◽  
Vol 475-479 ◽  
pp. 3459-3462
Author(s):  
Hong Bin Wang ◽  
Xiao Yu Wang ◽  
J.H. Zhang ◽  
T.Y. Hsu
Keyword(s):  
Mechanical Properties ◽  
Grain Growth ◽  
Coarse Grained ◽  
Growth Exponent ◽  
Face Centered Cubic ◽  
X Ray Diffraction ◽  
Ni Alloy ◽  
Face Centered ◽  
Fcc Phase

The grain growth and mechanical properties of nanograined bulk Fe-25at%Ni alloy prepared by an inert gas condensation and in-situ warm consolidation technique were investigated. About 43% high temperature face-centered-cubic (FCC) phase and 57% low temperature body-centered-cubic (BCC) phase were observed in the sample at room temperature, which was significantly different from that of the corresponding conventional coarse-grained alloy. The in-situ X-ray diffraction results show that the start and the finish temperature of BCC to FCC phase transformation are 450°C and 600°C, respectively. The isothermal grain growth exponent n from t k D D n n ¢ = − 1 0 1 for nanograined single FCC phase Fe-25at%Ni alloy is 0.38 at 750 °C . The mechanical properties changing with the grain size were studied by means of microindentation test.

Sign in / Sign up

Export Citation Format

Share Document