scholarly journals The Surface Integrity of Titanium Alloy When Using Micro-Textured Ball-End Milling Cutters

Micromachines ◽  
2018 ◽  
Vol 10 (1) ◽  
pp. 21 ◽  
Author(s):  
Shucai Yang ◽  
Song Yu ◽  
Chunsheng He
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Surface Integrity ◽  
Work Hardening ◽  
End Milling ◽  
Orthogonal Experiment ◽  
Processing Efficiency ◽  
Machined Surface ◽  
Surface Machining ◽  
Ball End Milling

Processing certain kinds of micro-textures onto the surface of tools can improve their wear resistance, reduce the friction between them and machined surfaces, prolong their service life and improve their processing efficiency. When milling titanium alloy with ball-end milling cutters, the cutting force and the cutting heat causes plastic deformation and a concentration of stress on workpiece surfaces, damaging their surface integrity. In this paper, we report on a test involving the milling of titanium alloy, where a micro-texture was placed onto the front of a ball-end cutter and the surface roughness and work hardening of the machined surface were studied. The orthogonal experiment was designed around changes in the diameter of the micro-texture, its depth, the spacing between individual micro-pits, and its distance from the cutting edge. Data from the experiment was then used to assess the influence changes in the micro-texture parameters had upon the roughness and hardening of the surface. The data was processed and analyzed by using regression analysis and a prediction model for surface roughness and work hardening was established. The reliability of the model was then verified. The contents of this paper provide a theoretical basis for improving the cutting performance and the surface machining quality of cemented carbide tools.

Comparison of surface integrity of Ti6Al4V titanium alloy manufactured by laser deposition and traditional method after end milling

2020 ◽  
pp. 095440622097213
Author(s):  
Ben Wang ◽  
Qi Zhang ◽  
Minghai Wang ◽  
Yaohui Zheng ◽  
Xianjun Kong
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Surface Integrity ◽  
Work Hardening ◽  
End Milling ◽  
Orthogonal Experiment ◽  
High Strength ◽  
Laser Deposition ◽  
Ti Alloy ◽  
Ti6al4v Titanium Alloy

Ti alloy has been widely applied in aerospace due to its high strength, good corrosion resistance, and excellent high-temperature performances. The quality and usability of Ti alloy parts are closely related to surface integrity. In this study, a comparative analysis of the milling surface integrity between laser deposition manufacturing and traditional Ti6Al4V samples was conducted. End milling surfaces of additive and traditional Ti6Al4V samples were observed with an orthogonal experiment under different milling parameters from the perspectives of cutting force, surface morphology, surface roughness, subsurface damages, and microhardness. Results demonstrate that the additive Ti6Al4V sample has a slightly higher cutting force and surface roughness relative to traditional Ti6Al4V. This is related to the higher hardness and plasticity of the additive Ti6Al4V sample. There are unmelted powder particle defects on the milling surface of the additive Ti6Al4V sample and serious cracking defects on the subsurface of the additive Ti6Al4V sample. The microhardness of the work hardening layer and base of the additive Ti6Al4V sample is higher than that of traditional Ti6Al4V. Moreover, the additive Ti6Al4V sample presents higher work hardening and a larger depth of the hardening layer. These findings demonstrate that material properties and manufacturing processes can influence surface integrity significantly.

Surface Integrity and Fatigue Property of a High Speed Milled Titanium Alloy

2008 ◽  
Vol 53-54 ◽  
pp. 305-310 ◽  
Author(s):  
Guo Sheng Geng ◽  
Jiu Hua Xu
Keyword(s):  
Residual Stress ◽  
Surface Roughness ◽  
Titanium Alloy ◽  
Surface Integrity ◽  
Work Hardening ◽  
High Speed ◽  
Cutting Speed ◽  
Fatigue Property ◽  
Machined Surface ◽  
Metallurgical Structure

Surface integrity has a great effect on the fatigue property of titanium alloy. The surface integrity and fatigue property of a high speed milled Ti-6.5Al-2Zr-1Mo-1V (TA15) titanium alloy were investigated in this research. The main objective of this paper is to study the influence of milling speed on the surface integraty and fatigue property of the machined part. The surface roughness, work hardening, metallurgical structure and residual stress of the machined surface were studied in a cutting speed range of from 50m/min to 300m/min. To verify the relationship between cutting speed and the surface integrity of machined surface, the fatigue property of titanium alloy specimens milled at four different cutting speeds ranging from 50 to 200m/min were compared at two stress levels. This research shows that the cutting speed has little effect on the work hardening, metallurgical structure and residual stress, but the surface roughness decreases with the increasing cutting speed. Therefore, increasing milling speed has a positive effect on the surface integrity and fatigue property of the machined surface.

scholarly journals Experimental Study on Surface Integrity of Titanium Alloy Ti6Al4V by Ball End Milling

2018 ◽  
Vol 14 (1) ◽  
pp. 115-121 ◽  
Author(s):  
Pun Krishna Kaway ◽  
Xueping Zhang
Keyword(s):  
Titanium Alloy ◽  
Surface Integrity ◽  
Feed Rate ◽  
End Milling ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machined Surface ◽  
Ball End Milling ◽  
Titanium Alloy Ti6al4v ◽  
Cutting Speeds

Titanium alloy, Ti6Al4V, has been widely used in aerospace, automotive, biomedical, and chemical industries due to its exceptional strength to weight ratio, high temperature performance, and corrosion resistance. However, machinability of Ti6Al4V is poor due to high strength at elevated temperatures, low modulus, and low thermal conductivity. Poor machinability of Ti6Al4V deteriorates the surface integrity of the machined surface. Poor surface integrity causes high machining cost, surface defects, initiate cracks, and premature failure of the machined surface. Thus, it is indispensable to obtain better surface integrity when machining titanium alloy Ti6Al4V. Cutting parameters such as cutting speed, feed rate, and depth of cut have significant effect on the surface integrity when machining titanium alloy Ti6Al4V. Hence, this study investigates surface integrity of Ti6Al4V by ball end milling at different cutting speeds, feed rates, and depth of cuts. Microstructure of subsurface is studied at different cutting speeds, feed rates, and depth of cuts. The results show that the depth of deformation of subsurface increases with increase in the cutting speed, feed rate, and depth of cut. Journal of the Institute of Engineering, 2018, 14(1): 115-121

scholarly journals Influence of turning tool wear on the surface integrity and anti-fatigue behavior of Ti1023

2021 ◽  
Vol 13 (4) ◽  
pp. 168781402110112
Author(s):  
Li Xun ◽  
Wang Ziming ◽  
Yang Shenliang ◽  
Guo Zhiyuan ◽  
Zhou Yongxin ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Plastic Deformation ◽  
Titanium Alloy ◽  
Fatigue Life ◽  
Tool Wear ◽  
Surface Integrity ◽  
Low Cycle Fatigue ◽  
Fatigue Behavior ◽  
Machined Surface ◽  
Deformation Layer

Titanium alloy Ti1023 is a typical difficult-to-cut material. Tool wear is easy to occur in machining Ti1023, which has a significant negative effect on surface integrity. Turning is one of the common methods to machine Ti1023 parts and machined surface integrity has a direct influence on the fatigue life of parts. To control surface integrity and improve anti-fatigue behavior of Ti1023 parts, it has an important significance to study the influence of tool wear on the surface integrity and fatigue life of Ti1023 in turning. Therefore, the effect of tool wear on the surface roughness, microhardness, residual stress, and plastic deformation layer of Ti1023 workpieces by turning and low-cycle fatigue tests were studied. Meanwhile, the influence mechanism of surface integrity on anti-fatigue behavior also was analyzed. The experimental results show that the change of surface roughness caused by worn tools has the most influence on anti-fatigue behavior when the tool wear VB is from 0.05 to 0.25 mm. On the other hand, the plastic deformation layer on the machined surface could properly improve the anti-fatigue behavior of specimens that were proved in the experiments. However, the higher surface roughness and significant surface defects on surface machined utilizing the worn tool with VB = 0.30 mm, which leads the anti-fatigue behavior of specimens to decrease sharply. Therefore, to ensure the anti-fatigue behavior of parts, the value of turning tool wear VB must be rigorously controlled under 0.30 mm during finishing machining of titanium alloy Ti1023.

Parameter Optimization of Ball End Milling Process on Inconel 718 Using RSM and TLBO Algorithm

2015 ◽  
Vol 15 (3) ◽  
pp. 293-300 ◽  
Author(s):  
Nandkumar N. Bhopale ◽  
Nilesh Nikam ◽  
Raju S. Pawade
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Surface Integrity ◽  
Inconel 718 ◽  
Tool Path ◽  
End Milling ◽  
Spindle Speed ◽  
Depth Of Cut ◽  
Ball End Milling

AbstractThis paper presents the application of Response Surface Methodology (RSM) coupled with Teaching Learning Based Optimization Technique (TLBO) for optimizing surface integrity of thin cantilever type Inconel 718 workpiece in ball end milling. The machining and tool related parameters like spindle speed, milling feed, axial depth of cut and tool path orientation are optimized with considerations of multiple response like deflection, surface roughness, and micro hardness of plate. Mathematical relationship between process parameters and deflection, surface roughness and microhardness are found out by using response surface methodology. It is observed that after optimizing the process that at the spindle speed of 2,000 rpm, feed 0.05 mm/tooth/rev, plate thickness of 5.5 mm and 15° workpiece inclination with horizontal tool path gives favorable surface integrity.

Surface Integrity Studies in Ball End Milling of Thin Shaped Cantilever Inconel 718

2014 ◽  
Author(s):  
Nandkumar N. Bhopale ◽  
Raju S. Pawade
Keyword(s):  
Surface Integrity ◽  
Inconel 718 ◽  
Tool Path ◽  
Surface Defects ◽  
End Milling ◽  
Surface Region ◽  
Lower Surface ◽  
Machined Surface ◽  
Ball End Milling ◽  
Integrity Analysis

The paper presents the surface integrity analysis in ball end milling of thin shaped cantilever plate of Inconel 718. It is noticed that the workpiece deflection has significantly contributed to machined surface integrity in terms of surface topography and subsurface microhardness. The ball end milling performed with 15° workpiece inclination with horizontal tool path produced higher surface integrity which varies with the location of machined surface region. In general, the mid portion of the machined plate shows lower surface roughness and microhardness with less surface defects.

scholarly journals Effect of Tool Orientation on Surface Integrity During Ball End Milling of Titanium Alloy TC17

Procedia CIRP ◽  
2016 ◽  
Vol 56 ◽  
pp. 143-148 ◽  
Author(s):  
Pan Yang ◽  
Changfeng Yao ◽  
Shaohua Xie ◽  
Dinghua Zhang ◽  
Dou Xing Tang
Keyword(s):  
Titanium Alloy ◽  
Surface Integrity ◽  
End Milling ◽  
Tool Orientation ◽  
Ball End Milling

An Approach to Improve Cutting Performance in Micromilling of Titanium Alloy

2020 ◽  
Vol 8 (2) ◽  
Author(s):  
Yunn-Shiuan Liao ◽  
Tsung-Hsien Li ◽  
Yi-Chen Liu
Keyword(s):  
Carbon Dioxide ◽  
Surface Roughness ◽  
Titanium Alloy ◽  
Flank Wear ◽  
End Milling ◽  
Cutting Speed ◽  
Liquid Carbon ◽  
Dry Cutting ◽  
Machined Surface ◽  
Liquid Carbon Dioxide

Abstract Application of liquid carbon dioxide to improve cutting performance in micro-end milling of Ti-6Al-4V titanium alloy was proposed in this study. It was found that the machined roughness decreased with the cutting speed as observed in the conventional cutting, when a 0.5 mm diameter end milling cutter was used in dry cutting. But, the tiny and shattered chips produced by the use of 0.3 mm diameter cutter could adhere on the machined surface and deteriorate surface finish, if the cutting speed was higher than 40 m/min. Cutting temperature was effectively decreased by applying liquid carbon dioxide during micromilling, which in turn reduced the amount of chips adhering on the machined surface and lowered flank wear. The surface roughness Ra at a cutting speed of 70 m/min was improved from 0.09 μm under dry cutting to 0.04 μm under the liquid carbon dioxide assisted cutting condition. And there were no flank wear and very few burrs left on the machined surface for the condition used in the experiment. The height of the burrs was only 25% of that under dry cutting. More, minimum quantity lubrication (MQL) was proposed to be applied together with the liquid carbon dioxide to enhance lubrication effect. It was noted that the machined surface roughness was further decreased by 15% as compared with that when the liquid carbon dioxide was applied alone. The height of burrs was reduced from 32 μm to 16 μm.

Experimental Research of Effective Cutting Speed Influence on Surface Roughness in Ball End Milling of C45 Material with Hardness 34 HRC

2014 ◽  
Vol 657 ◽  
pp. 53-57 ◽  
Author(s):  
Sándor Ravai Nagy ◽  
Ioan Paşca ◽  
Mircea Lobonțiu ◽  
Mihai Banica
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Experimental Research ◽  
Inclination Angle ◽  
Cutting Tool ◽  
End Milling ◽  
Cutting Speed ◽  
Cnc Machine Tools ◽  
Machined Surface ◽  
Ball End Milling

Machining of Complex Concave or Convex Surfaces Requires the Use of Ball End Milling Cutters. Obtaining the Expected Surface Quality Compete Various Technological Factors which should be Taken into Account. Following the Machining of the Surface with Different Inclination Angles between the Cutting Tool Axes and the Machined Surface, Significant Changes of the Surface Roughness have been Observed. Based on the Tests Performed, we can Determine the Range of the Tool Inclination Angle, which is the Best for the Surface Quality. we have also Made a Correlation between the Cutting Speeds, Inclination Angle of the Cutting Tool Toward the Machined Surface for an Obtained Surface Quality. the Presented Results are Based on Experimental Research in Industrial Conditions by Using CNC Machine Tools with 5 Axes. the Tests have been Performed on the C45 Material, Heat Treated to 34HRC.

Sign in / Sign up

Export Citation Format

Share Document