scholarly journals Quantification and Modelling of the Multiphase-Coupled Strengthening Effect in Al-Cu-Li Alloy

Metals ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 1038
Author(s):  
Jin Zhang ◽  
Zhide Li ◽  
Fushun Xu ◽  
Chongjun Bao
Keyword(s):  
Heat Treatment ◽  
Aluminum Alloys ◽  
Precipitation Strengthening ◽  
Strengthening Effect ◽  
Superposition Model ◽  
Aging Heat Treatment ◽  
Volume Fractions ◽  
Age Strengthening ◽  
Precipitated Phases ◽  
Strengthening Phases

After aging heat treatment, Al-Cu-Li alloy, in general, contains a variety of precipitated phases that jointly influence the age-strengthening effect on the alloy. In this work, a multiphase-coupled strengthening model has been established on the basis of a dislocation bypassing mechanism. The model considered situations with different proportions of two strengthening phases, T1 and θ′, and then obtained the dimension and volume fractions of these two strengthening phases via experiments. The values predicted by the multiphase-coupled strengthening model and the classical strengthening superposition model were compared with the measured results. The multiphase-coupled strengthening model established in this work had better consistency with the measured results. Moreover, the modeling method proposed in the paper can also be extended to the system having over two primary strengthening phases. Hence, the model can contribute towards the development of a multi-component precipitation strengthening process for aluminum alloys.

scholarly journals Effect of Retrogression and Re-Aging Heat Treatment on Hardness, Tensile Strength and Microstructure of 7075 Aluminum Alloy

2021 ◽  
Vol 28 (2) ◽  
pp. 63-68
Author(s):  
Mohamad Yehea Al nefawy ◽  
Fouad El dahiye
Keyword(s):  
Heat Treatment ◽  
Tensile Strength ◽  
Aluminum Alloy ◽  
Aluminum Alloys ◽  
7075 Aluminum Alloy ◽  
Aging Heat Treatment ◽  
Different Temperatures ◽  
Aluminum Alloy 7075

Retrogression and Re-Aging (RRA) Heat Treatment improves the tensile of aluminum alloys. In this research, to study the effect of Retrogression temperature and Retrogression time on the hardness, tensile strength and microstructure of 7075 aluminum alloy, have been applied. Retrogression treatments at different temperatures 180°C, 240°C and 370°C for 30 min and 90 min. When the retrogression temperature was 180°C for 30 min, the alloy has reached its highest hardness and tensile strength; they were respectively 165 HB and 586 MPa. RRA treatment of aluminum alloy 7075 led to precipitate a smoother, more homogeneous, and denser phase compared to the T6 treatment.

scholarly journals Probability-Dependent Precipitation Strengthening Effect of Anisotropic Precipitate in Al-Mg-Si Alloy Produced by T6 Heat Treatment

2021 ◽  
Vol 59 (8) ◽  
pp. 515-523
Author(s):  
Seunggyu Choi ◽  
Gwanghun Kim ◽  
Jin Pyeong Kim ◽  
Se Hoon Kim ◽  
Seung Bae Son ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Yield Strength ◽  
Metastable Phase ◽  
Precipitation Strengthening ◽  
Precipitate Size ◽  
Strengthening Effect ◽  
Alloy Matrix ◽  
Gravity Casting ◽  
T6 Heat Treatment ◽  
Critical Resolved Shear Stress

This study proposed a constitutive equation to predict the change in yield strength according to the behavior of β″ metastable precipitates, which have a profound effect on strength among materials precipitated during the T6 heat treatment of Al-Mg-Si alloy. The β″ precipitate is a metastable phase before it becomes a β (Mg2Si) precipitate, and is distributed in the form of nano-scale rods in the aluminum alloy matrix. Existing precipitation strengthening models assume the shape of the precipitate to be spherical, and in that case the equation that depends on the Orowan mechanism with the average precipitate size and distribution should dominate. However, precipitates are formed in various shapes and sizes by anisotropic growth. In particular, rod-shaped precipitates are not suitable for the existing precipitation strengthening model. In this study, an Al-Mg-Si alloy was fabricated by gravity casting followed by T6 heat treatment. The new precipitation strengthening effect equation proposes that the β″ precipitate affects yield strength during plastic deformation of the Al-Mg-Si alloy. The proposed precipitation strengthening effect equation probabilistically considers the Critical Resolved Shear Stress (CRSS), which varies depending on the angle between the dislocation and the precipitate, when the dislocation passes through a rod-shaped precipitate.

Effect of Heat Treatment on Microstructure and Properties of Cu-3Ti-1Al Alloy

2013 ◽  
Vol 749 ◽  
pp. 282-286
Author(s):  
Xian Hui Wang ◽  
Xiao Chun Sun ◽  
Xiao Hong Yang ◽  
Shu Hua Liang
Keyword(s):  
Heat Treatment ◽  
Solid Solution ◽  
Electrical Conductivity ◽  
Electron Microscope ◽  
Treatment Process ◽  
Intermetallic Phase ◽  
Strengthening Effect ◽  
Microstructure And Properties ◽  
Optimal Heat Treatment ◽  
Transmission Electron

The effect of heat treatment on the microstructure and properties of Cu-3Ti-1Al alloy was investigated. The microstructure was characterized by scanning electron microscope (SEM) and transmission electron microscope (TEM), and the hardness and electrical conductivity were tested as well. The results showed that the hardness and electrical conductivity of Cu-3Ti-1Al alloy increased significantly after solid solution and ageing treatment. The strengthening effect of Cu-3Ti-1Al alloy was attributed to the formation of intermetallic phase such as Ti3Al and fine precipitates of coherent β-Cu4Ti. With increase of the aging time and the temperature, the precipitates became coarse and incoherent with Cu matrix, and the discontinuous precipitate β started to grow from grain boundaries toward grain interior, which decreased hardness. As the formation of Ti3Al, β-Cu3Ti and β-Cu4Ti phase can efficiently reduce Ti concentration in Cu matrix. The electrical conductivity of Cu-3Ti-1Al alloy increases. In the range of experiments, the optimal heat treatment process for Cu-3Ti-1Al alloy is solid solution at 850°C for 4h and ageing 500°C for 2h, and the hardness and electrical conductivity are 227HV and 12.3%IACS, respectively.

The Effect of Aging Heat Treatment on the Microstructure and Mechanical Properties of 10Cr20Ni25Mo1.5NbN Austenitic Steel

2016 ◽  
Vol 35 (1) ◽  
pp. 1-7 ◽  
Author(s):  
Zhiyuan Liang ◽  
Wanhua Sha ◽  
Qinxin Zhao ◽  
Chongbin Wang ◽  
Jianyong Wang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Heat Treatment ◽  
Austenitic Steel ◽  
Treatment Time ◽  
Aging Treatment ◽  
Secondary Phases ◽  
Aging Heat Treatment ◽  
Microstructure And Mechanical Properties ◽  
The Impact

AbstractThe effect of aging heat treatment on the microstructure and mechanical properties of 10Cr20Ni25Mo1.5NbN austenitic steel was investigated in this article. The microstructure was characterized by scanning electron microscopy, energy dispersive spectrometry and transmission electron microscopy. Results show that the microstructure of 10Cr20Ni25Mo1.5NbN austenitic is composed of austenite. This steel was strengthened by precipitates of secondary phases that were mainly M23C6 carbides and NbCrN nitrides. As aging treatment time increased, the tensile strength first rose (0–3,000 h) and then fell (3,000–5,000 h) due to the decrease of high density of dislocations. The impact absorbed energy decreased sharply, causing the sulfides to precipitate at the grain boundary. Therefore, the content of sulfur should be strictly controlled in the steelmaking process.

Strength of Commercial Aluminum Alloys after Equal Channel Angular Pressing and Post-ECAP Processing

2006 ◽  
Vol 114 ◽  
pp. 91-96 ◽  
Author(s):  
Maxim Yu. Murashkin ◽  
M.V. Markushev ◽  
Julia Ivanisenko ◽  
Ruslan Valiev
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Aluminum Alloys ◽  
Ultimate Tensile Strength ◽  
Equal Channel Angular Pressing ◽  
Room Temperature ◽  
Solution Treatment ◽  
Ecap Processing ◽  
Angular Pressing

The effects of equal channel angular pressing (ECAP), further heat treatment and rolling on the structure and room temperature mechanical properties of the commercial aluminum alloys 6061 (Al-0.9Mg-0.7Si) and 1560 (Al-6.5Mg-0.6Mn) were investigated. It has been shown that the strength of the alloys after ECAP is higher than that achieved after conventional processing. Prior ECAP solution treatment and post-ECAP ageing can additionally increase the strength of the 6061 alloy. Under optimal ageing conditions a yield strength (YS) of 434 MPa and am ultimate tensile strength (UTS) of 470 MPa were obtained for the alloy. Additional cold rolling leads to a YS and UTS of 475 and 500 MPa with 8% elongation. It was found that the post-ECAP isothermal rolling of the 1560 alloy resulted in the formation of a nano-fibred structure and a tensile strength (YS = 540 MPa and UTS = 635 MPa) that has never previously been observed in commercial non-heat treatable alloys.

Uphill Quenching of Aluminum Alloys

2019 ◽  
Author(s):  
Wellington da Silva Mattos ◽  
George Edward Totten ◽  
Lauralice de Campos Franceschini Canale
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Residual Stress ◽  
Aluminum Alloys ◽  
Temperature Gradient ◽  
Dimensional Stability ◽  
Steam Chamber ◽  
Conventional Heat Treatment ◽  
Quenching Process ◽  
Uphill Quenching

This article describes the concept of uphill quenching process applied in the heat treatment of aluminum alloys. Uphill quenching is interesting since residual stress reductions of up to 80% has been reported. In addition, substantial improvements in dimensional stability have been achieved for several types of aluminum parts. Often, uphill quenching is applied after quenching and before aging during the heat treatment of aluminum alloys. The uphill quenching process consists of the immersion of the part in a cryogenic environment, and after homogenization of the temperature, the part is transferred to the hot steam chamber to obtain a temperature gradient that will maintain the mechanical properties gained with this process. The results obtained are lower residual stress and better dimensional stability. The aim of this article is to provide a review of this process and to compare it with conventional heat treatment.

Retrogression and Re-aging Heat Treatment: AA7XXX Aluminum Alloys

2019 ◽  
Author(s):  
V. Anil Kumar ◽  
S. Arjun ◽  
R.K. Gupta ◽  
P.V. Venkitakrishnan
Keyword(s):  
Heat Treatment ◽  
Aluminum Alloys ◽  
Industrial Applications ◽  
Age Hardening ◽  
Large Cross Section ◽  
Structural Applications ◽  
The Matrix ◽  
Peak Aged ◽  
Aged Temper ◽  
Short Time

Retrogression and re-aging (RRA) treatment was introduced to increase the stress corrosion cracking (SCC) resistance while retaining the strength attainable in T6 (peak aged) temper. Retrogression is a short-term heat treatment at an elevated temperature wherein a partial dissolution of metastable precipitates occurs, which are responsible for the hardening. During the next step, the material is re-aged in the regime of typical age hardening parameters to restore the strength with improved ductility. Response of RRA treatment has been reported on AA7XXX series Aluminum alloys such as AA7075, AA7050, AA7150, AA7049, and AA7010. Studies have been done on the effect of RRA on microstructure, mechanical properties such as tensile and hardness, corrosion, exfoliation corrosion, and SCC resistance by various researchers. The key characteristic of RRA is retrogression, which makes the re-precipitation in the matrix and coarsening of grain boundary precipitates such as MgZn2, η′. The retrogression treatment however requires high temperature and a short time, which limits the industrial application of RRA, especially in the heat treatment of the components with large cross section, due to the inherent thermal conductivity limitations. Hence, further work needs to be done in this area to apply this specialized heat treatment for industrial applications. This article brings out a comprehension of the changes in microstructure, tensile properties, and corrosion resistance of the various commonly used AA7XXX Aluminum alloys in structural applications with RRA heat treatment. The future scope of the work in RRA heat treatment is also discussed in this article.

scholarly journals Effect of Pre/Post Heat Treatment on the Friction Stir Welded SSM 356 Aluminum Alloys

2012 ◽  
Vol 32 ◽  
pp. 1139-1146 ◽  
Author(s):  
W. Boonchouytan ◽  
T. Ratanawilai ◽  
P. Muangjunburee
Keyword(s):  
Heat Treatment ◽  
Aluminum Alloys ◽  
Post Heat Treatment ◽  
Friction Stir
Sign in / Sign up

Export Citation Format

Share Document