scholarly journals Mechanical Amorphization and Recrystallization of Mn-Co(Fe)-Ge(Si) Compositions

Metals ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 534 ◽  
Author(s):  
Antonio Vidal-Crespo ◽  
Jhon J. Ipus ◽  
Javier S. Blázquez ◽  
Alejandro Conde
Keyword(s):  
Room Temperature ◽  
Crystal Size ◽  
Milling Time ◽  
Phase Evolution ◽  
Intermetallic Phases ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Bcc Phase ◽  
Thermal Stability Of

Mechanical alloying using a planetary ball mill allowed us to obtain two homogeneous systems formed by units with nanometer size and MnCo0.8Fe0.2Ge1−xSix stoichiometry (x = 0 and 0.5). The phase evolution of the systems with the milling time was analyzed using X-ray diffraction. Thermal stability of the final products was studied using differential scanning calorimetry. Room temperature 57Fe Mössbauer spectroscopy was used to follow the changes in the Fe environments. A paramagnetic Co-based amorphous phase developed in both alloys as milling progressed. However, while the presence of Si stabilized the Mn-type phase, mechanical recrystallization was observed in a Si-free composition leading to the formation of a MnCo(Fe)Ge intermetallic (Pnma space group) with a crystal size of 7 ± 1 nm. Mössbauer results indicate that Fe atoms migrate from the initial bcc phase to the amorphous and intermetallic phases.

Microstructure Evolution of a Fine Grain Al-50wt%Si Alloy Fabricated by High Energy Milling

2011 ◽  
Vol 479 ◽  
pp. 54-61 ◽  
Author(s):  
Fei Wang ◽  
Ya Ping Wang
Keyword(s):  
Grain Growth ◽  
Microstructure Evolution ◽  
Room Temperature ◽  
Milling Time ◽  
High Energy ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Laser Method ◽  
X Ray ◽  
Fine Grain

Microstructure evolution of high energy milled Al-50wt%Si alloy during heat treatment at different temperature was studied. Scanning electron microscope (SEM) and X-ray diffraction (XRD) results show that the size of the alloy powders decreased with increasing milling time. The observable coarsening of Si particles was not seen below 730°C in the high energy milled alloy, whereas, for the alloy prepared by mixed Al and Si powders, the grain growth occurred at 660°C. The activation energy for the grain growth of Si particles in the high energy milled alloy was determined as about 244 kJ/mol by the differential scanning calorimetry (DSC) data analysis. The size of Si particles in the hot pressed Al-50wt%Si alloy prepared by high energy milled powders was 5-30 m at 700°C, which was significantly reduced compared to that of the original Si powders. Thermal diffusivity of the hot pressed Al-50wt%Si alloy was 55 mm2/s at room temperature which was obtained by laser method.

scholarly journals Effect of Transition Elements on the Thermal Stability of Glassy Alloys 82Al–16Fe–2TM (TM: Ti, Ni, Cu) Prepared by Mechanical Alloying

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3978
Author(s):  
Nguyen Thi Hoang Oanh ◽  
Do Nam Binh ◽  
Dung Dang Duc ◽  
Quyen Hoang Thi Ngoc ◽  
Nguyen Hoang Viet
Keyword(s):  
Thermal Stability ◽  
Crystallization Process ◽  
Amorphous Matrix ◽  
Intermetallic Phases ◽  
Transition Elements ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Glassy Alloys ◽  
Thermal Stability Of

In the present study, the thermal stability and crystallization behavior of mechanical alloyed metallic glassy Al82Fe16Ti2, Al82Fe16Ni2, and Al82Fe16Cu2 were investigated. The microstructure of the milled powders was characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), and differential scanning calorimetry (DSC). The results showed remarkable distinction in thermal stability of the alloys by varying only two atomic percentages of transition elements. Among them, Al82Fe16Ti2 alloy shows the highest thermal stability compared to the others. In the crystallization process, exothermal peaks corresponding to precipitation of fcc-Al and intermetallic phases from amorphous matrix were observed.

Mechanisms of Phase Formation During Milling in the Ternary Immiscible AG-CU-FE System

1995 ◽  
Vol 400 ◽  
Author(s):  
T. Klassen ◽  
U. Herr ◽  
R.S. Averback
Keyword(s):  
Milling Time ◽  
Phase Evolution ◽  
Final States ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Two Phase ◽  
X Ray ◽  
Thermally Activated ◽  
Energetic Model ◽  
Fcc Alloy

AbstractPowder blends consisting of prealloyed FCC Ag-Cu solid solutions and elemental Fe powders were ball milled in overall compositions of Ag25Cu50Fe25, andAg40Cu20Fe40. The phase evolution with milling time was investigated by x-ray diffraction and differential scanning calorimetry. For the sample with higher Cu concentration, a ternary FCC alloy phase was formed, while milling the other sample resulted in a two phase mixture consisting of a Ag-rich FCC and an Fe-rich BCC solid solution. About the same amount of enthalpy between 12 and 13 kJ/g-atom is stored in the final states for the two different compositions. Two models based on kinetic and energetic considerations will be discussed and compared to the results. The kinetic model is based on the competition between forced atomic motion during shearing, which is driving the system towards a homogeneous alloy, and thermally activated diffusion, which favors phase separation. For the energetic model, the energy balance is calculated and a phase transformation is expected, if the required energy can be stored in phase boundaries.

scholarly journals Viability of the microencapsulation of a casein hydrolysate in lipid microparticles of cupuacu butter and stearic acid

2013 ◽  
Vol 2 (1) ◽  
Author(s):  
Samantha Cristina Pinho ◽  
Janaina Costa Da Silva
Keyword(s):  
Stearic Acid ◽  
Room Temperature ◽  
Casein Hydrolysate ◽  
Polysorbate 80 ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Initial Amount ◽  
X Ray ◽  
Lipid Mixtures ◽  
Lipid Microparticles

Solid lipid microparticles produced with a mixture of cupuacu butter and stearic acid were used to microencapsulate a commercial casein hydrolysate (Hyprol 8052). The composition of the lipid matrix used for the production of the lipid microparticles was chosen according to data on the wide angle X-ray diffraction (WAXD) and differential scanning calorimetry (DSC) of bulk lipid mixtures, which indicated that the presence of 10 % cupuacu butter was sufficient to significantly change the crystalline arrangement of pure stearic acid. Preliminary tests indicated that a minimum proportion of 4 % of surfactant (polysorbate 80) was necessary to produce empty spherical lipid particles with average diameters below 10 mm. The lipid microparticles were produced using 20 % cupuacu butter and 80 % stearic acid and then stabilized with 4 % of polysorbate 80, exhibiting an encapsulation efficiency of approximately 74 % of the casein hydrolysate. The melting temperature of the casein hydrolysate-loaded lipid microparticles was detected at 65.2 °C, demonstrating that the particles were solid at room temperature as expected and indicating that the incorporation of peptides had not affected their thermal behavior. After 25 days of storage, however, there was a release of approximately 30 % of the initial amount of encapsulated casein hydrolysate. This release was not thought to have been caused by the liberation of encapsulated casein hydrolysate. Instead, it was attributed to the possible desorption of the adsorbed peptides present on the surface of the lipid microparticles.

scholarly journals Structural and thermoelectric properties of the Pr2Zr2O7 compound

2019 ◽  
pp. 4-9
Author(s):  
Adolfo Quiroz-Rodríguez ◽  
Cesia Guarneros-Aguilar ◽  
Ricardo Agustin-Serrano
Keyword(s):  
Electron Microscopy ◽  
Thermal Conductivity ◽  
Thermoelectric Properties ◽  
Crystal Size ◽  
Ambient Pressure ◽  
X Ray Diffraction ◽  
X Ray ◽  
Increasing Temperature ◽  
Thermal Stability Of ◽  
Scanning Electron

In this research, it is presented a detailed study of the structural and thermoelectric properties of the pyrochlore zirconium Pr2Zr2O7 compound prepared by solid-state reaction (SSR) in air at ambient pressure. The synthesized sample was characterized using powder X-ray diffraction. The thermal stability of the thermoelectric compound (TE) Pr2Zr2O7 was tested by thermogravimetric analysis (TGA) and differential thermal analysis (DTA). Scanning electron microscopy shows that the crystal size varies between 0.69 and 2.81μm. Electrical conductivity (\sigma) of the sample calcined at 1400 °C presented values increase irregularly with the increasing temperature from 0.001 to 0.018 S cm-1 as expected in a semiconductor material. The thermal conductivity is lower than 0.44 - 775 W m-1 K-1 which is quite anomalous in comparison with the thermal conductivity of other oxides.

scholarly journals Characterization of the Interface Between the Bulk Glass Forming Alloy Zr41Ti14Cu12Ni10Be23 with Pure Metals and Ceramics

2000 ◽  
Vol 15 (7) ◽  
pp. 1617-1621 ◽  
Author(s):  
Jan Schroers ◽  
Konrad Samwer ◽  
Frigyes Szuecs ◽  
William L. Johnson
Keyword(s):  
Sessile Drop ◽  
Bulk Glass ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Glass Forming ◽  
Processing Times ◽  
Thermal Stability Of

The reaction of the bulk glass forming alloy Zr41Ti14Cu12Ni10Be23 (Vit 1) with W, Ta, Mo, AlN, Al2O3, Si, graphite, and amorphous carbon was investigated. Vit 1 samples were melted and subsequently solidified after different processing times on discs of the different materials. Sessile drop examinations of the macroscopic wetting of Vit 1 on the discs as a function of temperature were carried out in situ with a digital optical camera. The reactions at the interfaces between the Vit 1 sample and the different disc materials were investigated with an electron microprobe. The structure and thermal stability of the processed Vit 1 samples were examined by x-ray diffraction and differential scanning calorimetry. The results are discussed in terms of possible applications for composite materials.

Effect of Nitrogen Addition on Mechanical Property of Ti-Cr-Sn Alloy

2010 ◽  
Vol 654-656 ◽  
pp. 2126-2129 ◽  
Author(s):  
Yuichi Nakahira ◽  
Tomonari Inamura ◽  
Hiroyasu Kanetaka ◽  
Shuichi Miyazaki ◽  
Hideki Hosoda
Keyword(s):  
Mechanical Properties ◽  
Room Temperature ◽  
Tensile Tests ◽  
Nitrogen Addition ◽  
N Addition ◽  
X Ray Diffraction ◽  
Solution Hardening ◽  
X Ray ◽  
Bcc Phase ◽  
Cold Workability

Effect of nitrogen (N) addition on mechanical properties of Ti-Cr-Sn alloy was investigated in this study. Ti-7mol%Cr-3mol%Sn was selected and less than 0.5wt% of N were systematically added. The alloys were characterized by optical microscopy, X-ray diffraction analysis and tensile tests at room temperature. The apparent phase was β (bcc) phase, whereas the presence of precipitates was confirmed in 0.5wt%N-added alloy only which did not exhibit sufficient cold workability. The grain size was not largely affected by N addition being less than 0.5wt%. Tensile tests revealed that less than 0.5wt%N addition improves the strength which is due to the solution hardening by interstitial N atoms.

The Structure and Mechanical Properties of Plastically Consolidated Al-Ni Alloy

2016 ◽  
Vol 682 ◽  
pp. 245-251 ◽  
Author(s):  
Grzegorz Włoch ◽  
Tomasz Skrzekut ◽  
Jakub Sobota ◽  
Antoni Woźnicki ◽  
Justyna Cisoń
Keyword(s):  
Mechanical Properties ◽  
Vickers Hardness ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Intermetallic Phases ◽  
Scanning Calorimetry ◽  
Porosity Formation ◽  
X Ray ◽  
Ni Alloy ◽  
Thermal Stability Of

Mixed and preliminarily consolidated powders of aluminium and nickel (90 mass % Al and 10 mass % Ni) were hot extruded. As results the rod, 8 mm in diameter, was obtained. As-extruded material was subjected to the microstructural investigations using scanning electron microscopy (SEM/EDS) and X-ray analysis (XRD). The differential scanning calorimetry (DSC) and thermo-mechanical analysis (TMA) were also performed. The mechanical properties of as extruded material were determined by the tensile test and Vickers hardness measurements. In order to evaluate the thermal stability of PM alloy, samples were annealed at the temperature of 475 and 550 °C. After annealing Vickers hardness measurements and tensile tests were carried out. The plastic consolidation of powders during extrusion was found to be very effective, because no pores or voids were observed in the examined material. The detailed microstructural investigations and XRD analyses did not reveal the presence of the intermetallic phases in the as-extruded material. During annealing, the Al3Ni intermetallic compound was formed as the result of chemical reaction between the alloy components. The hardness of the alloy after annealing at the temperature of 475°C was found to be comparable to the hardness in as-extruded state. Annealing of the material at the temperature of 550°C results in hardness decreasing by about 50%, as the consequence of porosity formation and Al3Ni cracking.

Influence of Gd Addition on the Structure and Capability of Ni-Mn-In Metamagnetic Shape Memory Alloys

2012 ◽  
Vol 535-537 ◽  
pp. 950-953
Author(s):  
Li Na Bai ◽  
Gui Xing Zheng ◽  
Zhi Jian Duan ◽  
Jian Jun Zhang
Keyword(s):  
Differential Scanning Calorimetry ◽  
Magnetic Properties ◽  
Magnetic Property ◽  
Transition Temperature ◽  
Martensitic Transformation ◽  
Room Temperature ◽  
Vibrating Sample Magnetometry ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray

The influences of Gd concentration on martensitic transformation and magnetic properties of NiMnIn alloys were investigated by differential scanning calorimetry (DSC) , vibrating sample magnetometry (VSM), X-ray diffraction (XRD) and etc. It is Observed through the experiment: the addition of Gd enhances martensite transition temperature;X-ray diffraction analysis of experimental alloys is revealed that to the mixture is martensite and austenite at room temperature; content of Gd is not proportional to the improvement of magnetic property.

Study of thermal properties of Ga0.5In1.5Se3 by differential scanning calorimetry

2021 ◽  
pp. 2150407
Author(s):  
S. I. Ibrahimova
Keyword(s):  
Crystal Structure ◽  
Differential Scanning Calorimetry ◽  
Thermal Properties ◽  
Thermal Effects ◽  
Room Temperature ◽  
Structural Studies ◽  
X Ray Diffraction ◽  
Hexagonal Symmetry ◽  
Scanning Calorimetry ◽  
X Ray

The crystal structure and thermal properties of the [Formula: see text] compound have been investigated. Structural studies were performed by X-ray diffraction at room temperature. The crystal structure of this compound was found to correspond to the hexagonal symmetry of the space group P61. Thermal properties were studied using a differential scanning calorimetry (DSC). It was found in the temperature range [Formula: see text] that thermal effects occur at temperatures [Formula: see text] and [Formula: see text]. The thermodynamic parameters of these effects are calculated.

Sign in / Sign up

Export Citation Format

Share Document