scholarly journals Study on Friction Stir Lap Welding of Aluminium to Steel Sheets

Metals ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 498
Author(s):  
Lingfei Meng ◽  
Shujin Chen ◽  
Jiaqi Zhang ◽  
Di Wang ◽  
Hao Zhang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Melting Point ◽  
Welding Process ◽  
Zinc Content ◽  
Galvanized Steel ◽  
Formation Mechanisms ◽  
Friction Stir Lap Welding ◽  
Rotating Speed ◽  
Friction Stir ◽  
Lap Welding

Friction stir lap welding (FSLW) of 6061-T6 aluminium sheet and DX51D galvanized steel sheet was carried out by adding zinc foil to the lap interface and studying the influence of the zinc foil on the formation mechanisms and mechanical properties. The influence of the thickness of zinc foil, the plunge depth of the shoulder and the shape of the tools on the mechanical properties of the weld are discussed. Zinc foil reduced the generation of brittle intermetallic compounds, such as Fe4Al13. During the welding process, the axial force was small due to the high rotating speed. Liquid zinc was retained at the interface, where eutectic Al–Zn with low melting point and an Fe–Zn compound were generated to achieve the metallurgical combination of aluminium and steel. The fracture was located in the heat affected zone (HAZ) of the 6061-T6 base aluminium. The results showed that when the zinc foil was too thin, there was less zinc content at the interface; the resulting Al–Zn eutectic had low melting point, was not fully spread and had poor continuity, resulting in poor mechanical properties. When the zinc foil was too thick, a large amount of zinc-based solid solution was generated at the interface, and most of the fracture occurred in the zinc-rich layer.

Dissimilar Friction Stir Lap Welding of AA2198 and AA7075 Sheets: Forces, Microstructure and Mechanical Properties

2021 ◽  
Author(s):  
Antonello Astarita ◽  
Fausto Tucci ◽  
Alessia Teresa Silvestri ◽  
Michele Perrella ◽  
Luca Boccarusso ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Welding Process ◽  
Processing Parameters ◽  
Processing Parameter ◽  
Friction Stir Lap Welding ◽  
Friction Stir ◽  
Lap Shear ◽  
Microstructure And Mechanical Properties ◽  
Lap Welding ◽  
Factorial Design Of Experiments

Abstract This paper deals with the dissimilar friction stir lap welding of AA2198 and AA7075 sheets. The influence of processing parameters, namely welding speed and tool rotational speed on joint features, microstructure, and mechanical properties were investigated implementing a full factorial design of experiments. During the welding process, axial and transversal forces were continuously measured using a dedicated sensed fixture aiming at the correlation of this processing parameter with the quality of the achieved joints. The reported outcomes showed a very narrow processing window in which it was possible to avoid the formation of defects while the formation of an hook was observed for all the joints welded. The influence of the weld bead morphology on the lap shear strength was elucidated proving that the strength is ruled by the hook morphology. A correlation between the process parameters and the forces arising was also attempted. The final microstructure of the joints was studied and explained and also compared with the microhardness results.

scholarly journals Dissimilar friction stir lap welding of AA2198 and AA7075 sheets: forces, microstructure and mechanical properties

2021 ◽  
Author(s):  
Antonello Astarita ◽  
Fausto Tucci ◽  
Alessia Teresa Silvestri ◽  
Michele Perrella ◽  
Luca Boccarusso ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Welding Process ◽  
Processing Parameters ◽  
Friction Stir Lap Welding ◽  
Friction Stir ◽  
Microhardness Distribution ◽  
Lap Shear ◽  
Microstructure And Mechanical Properties ◽  
Lap Welding ◽  
Factorial Design Of Experiments

AbstractThis paper investigates the dissimilar friction stir lap welding of AA2198 and AA7075 sheets. The influence of processing parameters, namely welding speed and tool rotational speed on joint features, microstructure, and mechanical properties were studied by implementing a full factorial design of experiments. Axial and transversal forces were continuously measured during the welding process using a sensed fixture aiming at the correlation of processing parameters, forces, and quality of the achieved joints. Obtained outcomes showed hook formation for all the combination of parameters and the existence of a very narrow processing window in which it is possible to avoid the formation of internal defects, such as grooves and tunnels. The influence of the weld bead morphology on the lap shear strength was elucidated proving that the strength is ruled by the hook morphology. The microstructure of the joints was studied and discussed considering also the microhardness distribution. Graphical abstract

Effects of Welding Parameters in Micro Friction Stir Lap Welding of Aluminum A1100

2013 ◽  
Vol 789 ◽  
pp. 356-359 ◽  
Author(s):  
Ario Sunar Baskoro ◽  
A.A.D. Nugroho ◽  
D. Rahayu ◽  
Suwarsono ◽  
Gandjar Kiswanto ◽  
...  
Keyword(s):  
Tilt Angle ◽  
Welding Process ◽  
Tool Material ◽  
Tensile Load ◽  
Welding Parameter ◽  
Welding Parameters ◽  
Friction Stir Lap Welding ◽  
Friction Stir ◽  
Lap Welding ◽  
Welding Processes

Technology of Friction Stir Welding (FSW) as a technique for joining metal is relatively new. In some cases on Aluminum joining, FSW gives better results compared with the Arc Welding processes, including the quality of welds and less distortion. FSW can even use milling machine or drilling machine, by replacing the tools and the appropriate accessories. The purpose of this study is to analyze the effect of process parameters onmicro Friction Stir Lap Weldingto the tensile load of welds. In this case, Aluminum material A1100, with thickness of 0.4 mm was used. Tool material of HSS material was shaped with micro grinding process. Tool shoulder diameter was 3 mm, while the diameter pin was 2 mm and a length of pin was 0.7 mm. The parameter variations used in this study were the variable of spindle speed (2300, 2600, and 2900 rpm), variable oftooltilt angle(0, 1, 2 degree) and a variable ofFeed rate(50, 60, 70 mm/min). Where the variation of these parameters will affect to the mechanical properties of welds (as response) was the tensile load. Analysis and optimization parameters between the micro FSLW parameters with the tensile load of welds, is used aResponse Surface Methods(RSM). From the result of experiment and analysis, it is shown that the important welding parameter in Micro Friction Stir Lap welding process is tilt angle.

scholarly journals Interface Characteristics and Mechanical Properties of Ultrasonic-Assisted Friction Stir Lap Welded 7075-T6 Aluminium Alloy

Materials ◽  
2020 ◽  
Vol 13 (23) ◽  
pp. 5335 ◽  
Author(s):  
Changshu He ◽  
Zhiqiang Zhang ◽  
Ying Li ◽  
Jingxun Wei ◽  
Menggang Zhai ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Ultrasonic Vibration ◽  
Fracture Mode ◽  
Fracture Strength ◽  
Shear Fracture ◽  
Friction Stir Lap Welding ◽  
Friction Stir ◽  
Ultrasonic Assisted ◽  
Lap Welding ◽  
Cold Lap

In this work, friction stir lap welding (FSLW) and ultrasonic-assisted friction stir lap welding (UAFSLW) was applied to 6-mm-thick 7075-T6 alloy sheets using three welding tools with the same process parameters. The joint formation, microstructural characteristics, and mechanical properties of the resulting lap joints were then investigated. The results showed that ultrasonic vibration significantly promoted the flow of metal at the interface, enlarged the size of the stirred zone (SZ), and reduced the angle between the hook defect and the interface. During lap shear testing, the FSLW and UAFSLW joints fractured in a similar manner. The fracture modes included tensile fracture, shear fracture, and a mixture of both. Cold lap and hook defects may have served as crack-initiation zones within the joint. Under configuration A (i.e., upper sheet on the retreating side (RS)), all joints failed in the shear-fracture mode. The effective lap width (ELW) of the joint welded using tool T2 was the greatest. This resulted in a higher shear fracture strength. The maximum shear fracture strength of the UAFSLW joint was 663.1 N/mm. Under configuration B (i.e., upper sheet on the advancing side (AS)), the shear fracture strength was greatly affected by the fracture mode. The highest shear fracture strength of the UAFSLW joint, 543.7 N/mm, was welded by tool T3. Thus, under otherwise identical conditions, UAFSLW joints can withstand a greater fracture shear strength than FSLW joints, as ultrasonic vibration helps to mix the material at the interface, thus, enlarging the SZ and diminishing the cold lap defects.

Sign in / Sign up

Export Citation Format

Share Document