scholarly journals Coarse Grained Heat-Affected Zone Microstructure and Brittleness of Ti-Nb-B Microalloyed High Toughness and Wear Resistant Steel

Metals ◽  
2019 ◽  
Vol 9 (3) ◽  
pp. 289
Author(s):  
Defa Li ◽  
Kaiming Wu ◽  
Hangyu Dong ◽  
Oleg Isayev ◽  
Oleksandr Hress
Keyword(s):  
Impact Toughness ◽  
Heat Affected Zone ◽  
High Hardness ◽  
Controlled Rolling ◽  
Coarse Grained ◽  
Coarse Grain ◽  
Theoretical Formula ◽  
Resistant Steel ◽  
Wear Resistant ◽  
The Impact

The effects of B, Ti-Nb, and Ti-Nb-B microalloying on the microstructure and properties of the coarse grain heat affected zone (CGHAZ) of C-Mn-Si-Mo wear-resistant steel have been investigated by means of thermal simulation, mechanical property test, microstructure analysis, and theoretical formula calculation. The B, Ti-Nb, and Ti-Nb-B microalloyed C-Mn-Si-Mo wear-resistant steels prepared by a controlled rolling + direct quenching + low temperature (CR + DQ + T) process have martensite/bainite (M/B) dual-phase microstructure and fully-refined effective grain size, which make the base metal to have high hardness and impact toughness. At the heat input of 20 kJ/cm, the impact toughness of CGHAZ of three kinds of microalloyed wear-resistant steels decreased in varying degrees. The main reasons for brittleness were coarse grain embrittlement and microstructural embrittlement. Ti-Nb-B microalloying can effectively prevent grain growth in CGHAZ while avoiding the formation of pearlite, small lump ferrite, and large grain carbides at the grain boundaries, thereby reducing the embrittlement of coarse grain and microstructure.

Effect of Welding Processes with High Heat Input on the Microstructure and Toughness of Coarse-Grained Heat-Affected Zone of a High-Strength High-Toughness Steel

2018 ◽  
Vol 937 ◽  
pp. 61-67
Author(s):  
Yu Jie Li ◽  
Jin Wei Lei ◽  
Xuan Wei Lei ◽  
Oleksandr Hress ◽  
Kai Ming Wu
Keyword(s):  
Low Temperature ◽  
Impact Toughness ◽  
Heat Affected Zone ◽  
Heat Input ◽  
High Strength ◽  
High Heat ◽  
Coarse Grained ◽  
Low Temperature Impact Toughness ◽  
The Impact ◽  
Welding Processes

Utilizing submerged arc welding under heat input 50 kJ/cm on 60 mm thick marine engineering structure plate F550, the effect of preheating and post welding heat treatment on the microstructure and impact toughness of coarse-grained heat-affected zone (CGHAZ) has been investigated. The original microstructure of the steel plate is tempered martensite. The yield and tensile strength is 610 and 660 MPa, respectively. The impact absorbed energy at low temperature (-60 °C) at transverse direction reaches about 230~270 J. Welding results show that the preheating at 100 °C did not have obvious influence on the microstructure and toughness; whereas the tempering at 600 °C for 2.5 h after welding could significantly reduce the amount of M-A components in the coarse-grained heat-affected zone and thus improved the low temperature impact toughness.

scholarly journals Effect of Tempering Temperature on Microstructures and Wear Behavior of a 500 HB Grade Wear-Resistant Steel

Metals ◽  
2019 ◽  
Vol 9 (1) ◽  
pp. 45 ◽  
Author(s):  
Erding Wen ◽  
Renbo Song ◽  
Wenming Xiong
Keyword(s):  
Electron Microscopy ◽  
Wear Resistance ◽  
Impact Toughness ◽  
Wear Behavior ◽  
Temper Embrittlement ◽  
Surface Hardness ◽  
Resistant Steel ◽  
Tempering Temperature ◽  
Wear Resistant ◽  
The Impact

The microstructure and wear behavior of a 500 Brinell hardness (HB) grade wear-resistant steel tempered at different temperatures were investigated in this study. The tempering microstructures and wear surface morphologies were studied by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The relationship between mechanical properties and wear resistance was analyzed. The microstructure of the steel mainly consisted of tempered martensite and ferrite. Tempered troosite was obtained when the tempering temperature was over 280 °C. The hardness decreased constantly with the increase of tempering temperature. The same hardness was obtained when tempered at 260 °C and 300 °C, due to the interaction of Fe3C carbides and dislocations. The impact toughness increased first and reached a peak value when tempered at 260 °C. As the tempering temperature was over 260 °C, carbide precipitation would occur along the grain boundaries, which led to temper embrittlement. The best wear resistance was obtained when tempered at 200 °C. At the initiation of the wear test, surface hardness was considered to be the dominant influencing factor on wear resistance. The effect of surface hardness improvement on wear resistance was far greater than the impact toughness. With the wear time extending, the crushed quartz sand particles and the cut-down burs would be new abrasive particles which would cause further wear. Otherwise, the increasing contact temperature would soften the matrix and the adhesive wear turned out to be the dominant wear mechanism, which would result in severe wear.

scholarly journals Impact Toughness of Gas Metal Arc Welded HY-80 Steel Plate at Sub-zero Temperatures

2019 ◽  
Vol 269 ◽  
pp. 06003
Author(s):  
Herry Oktadinata ◽  
Winarto Winarto
Keyword(s):  
Impact Toughness ◽  
Weld Joint ◽  
Heat Affected Zone ◽  
High Strength Steel ◽  
Steel Plate ◽  
Gas Metal Arc Welding ◽  
High Strength ◽  
Coarse Grain ◽  
Fracture Appearance ◽  
The Impact

Various welding methods are widely applied in large fabrication of high strength steel. However, commonly the problem occurs where a coarse grain is formed near fusion zone causing reduce the impact toughness due to the weld joint become brittle. Ductility and toughness in a coarse grain heat affected zone (CGHAZ) is low due to the formation of coarsening grain size. The objective of this research is to investigate the microstructure evolution, impact toughness and fracture appearance at sub-zero temperatures of the high strength steel arc welded. The steel that used in this experiment is a HY-80 steel welded by gas metal arc welding (GMAW) with a mixture of argon and carbon dioxide (90%Ar and 10%CO2) and ER100S solid wire. Microstructure observation and Charpy V-notch (CVN) tests were performed on the weld joint which consist of base metal (BM), heat affected zone (HAZ), and weld metal (WM). The CVN tests on the HY-80 steel plate at various temperatures (20, -20, -60 and -80 °C) show impact toughness decrease when the test temperature decrease. The CVN tests on the HY-80 weld joint at a temperature of 80 °C show the lowest impact toughness was measured at WM (61 J) and followed fusion line-FL (101 J) with brittle fracture appearance.

Mechanical Behaviour of Intercritically Reheated Coarse-Grained Heat Affected Zone in High Strength Line Pipe Steels

2018 ◽  
Author(s):  
Madhumanti Mandal ◽  
Warren J. Poole ◽  
Thomas Garcin ◽  
Matthias Militzer ◽  
Laurie Collins
Keyword(s):  
Impact Toughness ◽  
Heat Affected Zone ◽  
Welding Process ◽  
Charpy Impact ◽  
High Strength ◽  
Coarse Grained ◽  
Fracture Mechanisms ◽  
Line Pipe ◽  
Secondary Cracks ◽  
The Impact

Multipass welding of high strength steels used for fabrication and joining of transmission pipelines presents a number of metallurgical challenges. A key concern is both the strength and toughness of the heat affected zone (HAZ) adjacent to both seam and girth welds. In this work, a systematic study has been conducted on regions of the heat affected zone in the base metal where the first welding pass produces a thermal excursion which results in a coarse-grained heat affected zone (CGHAZ). The subsequent weld pass involves intercritical annealing of this region, i.e. a microstructure associated with intercritically reheated coarse grain heat affected zone (ICCGHAZ). The small ICCGHAZ region is often identified as being particularly susceptible to crack initiation. This work was undertaken to understand microstructure development in this zone and how the ICCGHAZ may affect the overall performance of the HAZ. Gleeble thermomechanical simulations have been conducted to produce bulk samples representative of different welding scenarios. Charpy impact tests and tensile tests have been performed over a range of temperatures. It was found that when a continuous necklace of martensite-austenite islands form on the prior austenite grain boundaries (i.e. for a M/A fraction of ≈10%), the Charpy impact toughness energy is dramatically decreased and the ductile brittle transition temperature is significantly raised. Detailed studies on the secondary cracks have been conducted to examine the fracture mechanisms in the different microstructures. The results show that the lower bainite microstructures obtained after the 1st thermal treatment, representative of CGHAZ have excellent impact properties. The impact toughness of the microstructures typical of ICCGHAZ is strongly dependent on the composition as well as morphology and spatial distribution of the resulting martensite-austenite (M/A) islands transformed from inter-critically formed austenite. This zone can play a significant role in fracture initiation and thus needs to be considered in alloy and welding process designs.

scholarly journals Comparison of Impact Toughness in Simulated Coarse-Grained Heat-Affected Zone of Al-Deoxidized and Ti-Deoxidized Offshore Steels

Metals ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 1783
Author(s):  
Henri Tervo ◽  
Antti Kaijalainen ◽  
Vahid Javaheri ◽  
Mohammed Ali ◽  
Tuomas Alatarvas ◽  
...  
Keyword(s):  
Impact Toughness ◽  
Heat Affected Zone ◽  
Electron Backscatter Diffraction ◽  
Cooling Time ◽  
Coarse Grained ◽  
X Ray Diffraction ◽  
X Ray ◽  
Electron Backscatter ◽  
Backscatter Diffraction ◽  
The Impact

The presence of acicular ferrite (AF) in the heat-affected zone (HAZ) of steels used offshore is generally seen as beneficial for toughness. In this study, the effects of varying fractions of AF (0–49 vol.%) were assessed in the simulated, unaltered and coarse-grained heat-affected zones (CGHAZ) of three experimental steels. Two steels were deoxidized, with one using Ti and the other using Al. The characterization was carried out by using electron microscopy, energy-dispersive X-ray spectrometry, electron backscatter diffraction and X-ray diffraction. The fraction of AF varied with the heat input and cooling time applied in the Gleeble thermomechanical simulator. AF was present in one of the Ti-deoxidized steels with all the applied cooling times, and its fraction increased with increasing cooling time. However, in other materials, only a small fraction (13–22%) of AF was present and only when the longest cooling time was applied. The impact toughness of the simulated specimens was evaluated using instrumented Charpy V-notch testing. Contrary to the assumption, the highest impact toughness was obtained in the conventional Al-deoxidized steel with little or no AF in the microstructure, while the variants with the highest fraction of AF had the lowest impact toughness. It was concluded that the coarser microstructural and inclusion features of the steels with AF and also the fraction of AF may not have been great enough to improve the CGHAZ toughness of the steels investigated.

Effect of Heat Input on Toughness of Coarse-Grained Heat-Affected Zone of an Ultra Low Carbon Acicular Ferrite Steel

2012 ◽  
Vol 538-541 ◽  
pp. 2003-2008 ◽  
Author(s):  
Zheng Hai Xia ◽  
Xiang Liang Wan ◽  
Xue Li Tao ◽  
Kai Ming Wu
Keyword(s):  
Electron Microscopy ◽  
Impact Toughness ◽  
Heat Affected Zone ◽  
Heat Input ◽  
Acicular Ferrite ◽  
High Heat ◽  
Coarse Grained ◽  
Low Carbon ◽  
Ferrite Steel ◽  
The Impact

The effect of heat input on toughness of coarse-grained heat-affected zone of an ultra low carbon acicular ferrite steel were investigated when the welding was conducted with high heat input. Microstructural observations, energy dispersive X-ray spectroscopy analyses were conducted using optical microscopy, scanning electron microscopy and transmission electron microscopy, respectively. The microstructures of coarse-grained heat-affected zone consist of predominantly bainitic microstructure and a small proportion of acicular ferrite grains. The bainitic microstructures become coarsened with increasing heat input. The impact toughness of coarse-grained heat-affected zone remained at a higher level when the heat input ranged from 42 to 55 kJ/cm. It became not stable and dropped to a lower level when the heat input increased to 110150 kJ/cm. The enhancement in impact toughness was attributable to the MnS precipitation on the pre-formed Ti oxides as well as the formation of intragranular ferrite. When specimens were welded with higher heat input, the deterioration of impact toughness was caused by the coarsening of austenite grains.

Microstructures and Toughness in Simulated Coarse Grain Heat-Affected Zones of Copper-Bearing Steel

2008 ◽  
Vol 575-578 ◽  
pp. 910-914
Author(s):  
Wen Yan Liu ◽  
Lai Wang ◽  
Ji Bin Liu ◽  
Ping He Li ◽  
Kai Miao ◽  
...  
Keyword(s):  
Impact Toughness ◽  
Heat Affected Zone ◽  
Physical Simulation ◽  
Bearing Steel ◽  
Granular Bainite ◽  
Coarse Grain ◽  
Factors Influencing ◽  
Visible Effect ◽  
Main Factors ◽  
The Impact

Microstructures and toughness of simulated coarse grain heat-affected zone of hot continuously rolled copper-bearing steel were investigated using physical simulation. The results showed that brittlement is easy to happen in the region of CGHAZ with slower thermal cycles (t8/5≥45s). Granular bainite transformed from austenite led to brittlement. The dimensions of granular martensite and austenite (M-A) constituents are main factors influencing the impact toughness. There is no visible effect on the toughness when the dimensions of M-A constituents are less than 1μ m. However, the toughness decreases greatly once the dimensions exceed 1μ m. Therefore, decreasing the dimensions of M-A constituents by controlling weld heat input will do good to improve the impact toughness of copper-bearing steel.

Effect of Heat Input on Impact Toughness of Coarse-Grained Heat-Affected Zone of a Nb-Ti Microalloyed Pipeline Steel

2012 ◽  
Vol 538-541 ◽  
pp. 2026-2031 ◽  
Author(s):  
Zhou Gao ◽  
Ran Wei ◽  
Kai Ming Wu
Keyword(s):  
Impact Toughness ◽  
Heat Affected Zone ◽  
Heat Input ◽  
Pipeline Steel ◽  
High Heat ◽  
Coarse Grained ◽  
Bainitic Microstructure ◽  
Homogenous Distribution ◽  
High Heat Input ◽  
The Impact

The effect of varying heat inputs (20, 100, 200 kJ/cm) on the microstructures and toughness of the simulated coarse-grained heat-affected zone of a Nb-Ti microalloyed pipeline steel were investigated utilizing optical and electron microscope. Results showed that the impact toughness of the coarse-grained heat-affected zone maintained a higher level at the heat input of 20 and 100 kJ/cm, whereas it dropped to a much lower level at the heat input of 200 kJ/cm. The good toughness was attributed to the grain refinement and the homogenous distribution of fine and elongated martensite/austenite constituents. The deterioration of toughness for high heat input simulated welding was mainly caused by the coarse bainitic microstructure and massive martensite/austenite constituents.

scholarly journals Effects of Small Ni Addition on the Microstructure and Toughness of Coarse-Grained Heat-Affected Zone of High-Strength Low-Alloy Steel

Metals ◽  
2018 ◽  
Vol 8 (9) ◽  
pp. 718 ◽  
Author(s):  
Gang Huang ◽  
Xiangliang Wan ◽  
Kaiming Wu ◽  
Huazhong Zhao ◽  
Raja Misra
Keyword(s):  
Impact Toughness ◽  
Alloy Steel ◽  
Heat Affected Zone ◽  
High Strength ◽  
Coarse Grained ◽  
Low Alloy Steel ◽  
Ni Content ◽  
Ni Addition ◽  
Bainitic Microstructure ◽  
The Impact

The objective of the present study is to investigate the effects of nickel (Ni) on the microstructure and impact toughness of coarse-grained heat-affected zone (CGHAZ) of high-strength low-alloy steel. It was observed that the microstructure of CGHAZ predominantly consisted of bainite and a small proportion of martensite-austenite (M-A) constituents and acicular ferrite (AF). With increased Ni content, the percentage of M-A constituent decreased and AF increased; consequently, the impact toughness of CGHAZ increased. The study revealed that a small addition of nickel significantly affected the formation of M-A constituents and AF; however, no obvious influence was observed on the bainitic microstructure of high-strength low-alloy steel.

Sign in / Sign up

Export Citation Format

Share Document