scholarly journals Numerical Simulation of Steel Reinforced Concrete (SRC) Joints

Metals ◽  
2019 ◽  
Vol 9 (2) ◽  
pp. 131 ◽  
Author(s):  
Isaac Montava ◽  
Ramon Irles ◽  
Jorge Segura ◽  
Jose Gadea ◽  
Ernesto Juliá
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Finite Element Model ◽  
Numerical Models ◽  
Experimental Tests ◽  
Element Model ◽  
Reinforced Concrete Beams ◽  
Plastic Behavior ◽  
Steel Reinforced Concrete ◽  
Concrete Joints

This paper presents a three-dimensional finite element model to confirm experimental tests carried out on steel reinforced concrete joints. The nonlinear behavior of this concrete is simulated, along with its reduced capability to resist large displacements in compression. The aim was to obtain the plastic behavior of reinforced concrete beams with a numerical model in the same way as obtained experimentally, in which the reduction of strength in the post-critical stage was considered to simulate behavior until structures collapsed. To do this, a nonlinear calculation was necessary to simulate the behavior of each material. Three numerical models provide a moment–curvature graph of the cross-section until collapse. Simulation of the structural elements is a powerful tool that avoids having to carry out expensive experimental tests. From the experimental results a finite element model is simulated for the non-linear analysis of steel reinforced concrete joints. It is possible to simulate the decreasing stress behavior of the concrete until reaching considerable displacement. A new procedure is discussed to capture the moment-curvature diagram. This diagram can be used in a simplified frame analysis, considering post-critical behavior for future research.

Uniform loading on the reinforced concrete beam produced by the specific cylinder-shaped rubber bags fully filled with air or water

2020 ◽  
Vol 23 (9) ◽  
pp. 1934-1947
Author(s):  
Dapeng Chen ◽  
Li Chen ◽  
Qin Fang ◽  
Yuzhou Zheng ◽  
Teng Pan
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Finite Element Model ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Element Model ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Uniform Loading ◽  
Air Bag

The bending behavior of reinforced concrete beams under uniform pressure is critical for the research of the blast-resistance performance of structural components under explosive loads. In this study, a bending test of five reinforced concrete beams with the dimensions of 200 mm (width) × 200 mm (depth) × 2500 mm (length) under uniform load produced by a specific cylinder-shaped rubber bag filled with air or water was conducted to investigate their flexural performances. An air bag load was applied to three of the reinforced concrete beams, a water bag load was applied to one reinforced concrete beam, and the remainder beam was subjected to the 4-point bending load. The experimental results highlighted that the air bag and water bag loading methods can be used to effectively apply uniform loads to reinforced concrete beams. Moreover, the stiffness of the air bag was improved by 123% in accordance with the initial pressure increases from 0.15 to 0.45 MPa. In addition, a finite element model of the test loading system was established using ABAQUS/Standard software. Moreover, the critical factors of the air bag loading method were analyzed using the numerical model. The calculated results were found to be in good agreement with the test data. The established finite element model can therefore be used to accurately simulate the action performances of the uniform loading technique using rubber bags filled with air or water.

scholarly journals Modeling the flexural behavior of corroded reinforced concrete beams with considering stirrups corrosion

2020 ◽  
Vol 14 (3) ◽  
pp. 26-39
Author(s):  
Nguyen Ngoc Tan ◽  
Nguyen Trung Kien
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Finite Element Model ◽  
Limit State ◽  
Nonlinear Behavior ◽  
Element Model ◽  
Reinforced Concrete Beams ◽  
Flexural Behavior ◽  
Bending Test ◽  
Fe Model

The reinforcement corrosion is one of the most dominant deterioration mechanisms of existing reinforced concrete structures. In this paper, the effects of the stirrup corrosion on the structural performance of five corroded beams have been simulated using the finite element model with DIANA software. These tested beams are divided into two groups for considering different inputs: (i) without corroded stirrups in flexural span, (ii) with locally corroded stirrups at different locations (e.g. full span, shear span, middle span). FE model has been calibrated with experimental results that were obtained from the four-point bending test carried out on the tested beams. This study shows that the stirrups corrosion should be received more attention in the serviceability limit state since its considerable effect on flexural behavior. Based on a parametric study, it shows that the effect of the cross-section loss of tension reinforcements on the load-carrying capacity of the corroded beam is more significant than the bond strength reduction. Keywords: reinforced concrete; beam; stirrup corrosion; finite element model; flexural nonlinear behavior.

Modeling of Steel-Reinforced Concrete Panels under Blast Loads

2014 ◽  
Vol 553 ◽  
pp. 100-105
Author(s):  
Xiao Shan Lin ◽  
Yi Xia Zhang ◽  
Paul Jonathan Hazell
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Finite Element Model ◽  
Strain Rate ◽  
Blast Loading ◽  
Element Model ◽  
Strain Rate Effect ◽  
Structural Behaviour ◽  
Steel Reinforced Concrete ◽  
Concrete Panels

In this study, a finite element model is developed for simulation of the structural behaviour of steel-reinforced concrete panels under blast loading using LS-DYNA. Pure Lagrangian formulation is applied in the finite element analysis, and the strain rate effect is taken into account in the material models of both concrete and steel. The finite element model is validated by comparing the computed results with experimental test results from the literature. Structural behaviour of concrete panel with different parameters under blast loading is also investigated. Keywords: Blast resistance; Finite element model; Reinforced concrete panel; Strain rate effect

scholarly journals Finite Element Model Updating of Reinforced Concrete Beams with Honeycomb Damage

2012 ◽  
Vol 58 (2) ◽  
pp. 135-151 ◽  
Author(s):  
Z. Ismail
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Finite Element Model ◽  
Model Updating ◽  
Element Model ◽  
Significant Loss ◽  
Reinforced Concrete Beams ◽  
Finite Element Model Updating ◽  
Finite Element Models ◽  
The Finite Element Model

Abstract A method of detecting honeycombing damage in a reinforced concrete beam using the finite element model updating technique was proposed. A control beam and two finite element models representing different severity of damage were constructed using available software and the defect parameters were updated. Analyses were performed on the finite element models to approximate the modal parameters. A datum and a control finite element model to match the datum test beams with honeycombs were prepared. Results from the finite element model were corrected by updating the Young’s modulus and the damage parameters. There was a loss of stiffness of 3% for one case, and a loss of 7% for another. The more severe the damage, the higher the loss of stiffness. There was no significant loss of stiffness by doubling the volume of the honeycombs.

scholarly journals Effect of Cyclic Loadings on the Shear Strength and Reinforcement Slip of RC Beams

2017 ◽  
Vol 3 (2) ◽  
pp. 111-123 ◽  
Author(s):  
Mohammed A Sakr
Keyword(s):  
Finite Element ◽  
Shear Strength ◽  
Reinforced Concrete ◽  
Finite Element Model ◽  
Failure Mode ◽  
Failure Modes ◽  
Concrete Beams ◽  
Kinematic Hardening ◽  
Element Model ◽  
Reinforced Concrete Beams

Numerous studies of the response of reinforced concrete members under cyclic loadings, many of which have been summarized and have indicated that, in general, the flexural strength of under-reinforced beams remains unimpaired under cyclic loadings consisting of a reasonable number of cycles. However, there is a body of evidence indicating that their shear strength may suffer under such loadings. The first objective of the current study is to construct an accurate 2D shell finite element model of reinforced concrete beams under cyclic loadings. The second objective is carrying out a parametric study on reinforced concrete beams, using the suggested 2D shell model.  The objective of this study was to observe the effect of the stirrup spacing, steel-to-concrete bond properties on the performance of reinforced concrete beams under cyclic loadings. For this purpose, an efficient and accurate finite element model was established taking into account the compression and tensile softening introducing damage in the concrete material, the Baushinger effect using nonlinear isotropic/kinematic hardening in the steel and an adequate bond-slip law for the concrete–steel interface. The simulated results of numerical models were verified by experimental results available in literature in order to validate the proposed model, including hysteretic curves, failure modes, crack pattern and debonding failure mode. The model provided a strong tool for investigating the performances of reinforced concrete beam. The results showed that: Cyclic loadings may change the failure mode of the beam to bond failure even though it has sufficient bond length to resist static loadings. So that under cyclic loadings additional anchorage length must be taken, cyclic loadings also influence the ductility and peak load for beams fail in shear. All these topics are of the utmost importance to RC behaviour to be considered by construction codes.

scholarly journals Flexural Strengthening of Reinforced Concrete Beams with Mechanically Bonded Steel Plates

2021 ◽  
Author(s):  
Syed Ali Kashif
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Finite Element Model ◽  
Steel Plate ◽  
Great Influence ◽  
Element Model ◽  
Composite Beams ◽  
Design Guidelines ◽  
Reinforced Concrete Beams ◽  
Design Procedures

Steel plate bonding technology is widely accepted for the strengthening of reinforced concrete structures. Researches in the past showed that epoxy bonded steel plated composite beams are highly prone to variation in temperature and environmental conditions. This research study introduces a novel approach to steel plate composite beam in which bond between the concrete and the steel plate is provided by welding the steel plate to the legs of the uniformly spaced stirrups. Experimental investigation showed that the parameters such as interface connections, geometric dimensions, stirrups spacing and thickness of steel plate have a great influence on the strength, deformation and failure characteristics of such composite beams. A finite element model has been developed using commercial software, ABAQUS, to predict the strength of such composite beams and its performance is validated through experimental results. The direct finite element simulation of proposed composite beams with developed finite element model gives an average of experimental to predicted strength ratio of 0.99, which comfirms the accuracy of prediction. The finite element model is then used to simulate a large number of numerical beams with varying geometric and material properties to formulate design guidelines. Design charts are developed and their performance is validated through test results with experimental to design chart predictions giving an average value of 0.94. Design procedures for such beams are illustrated with calculated design examples. Such simple design procedures can be adopted in the actual design of proposed composite beams in practical applications.

Numerical Simulation Technology of the Steel Reinforced Concrete Special-Shaped Columns Using Ansys

2012 ◽  
Vol 466-467 ◽  
pp. 1232-1236
Author(s):  
Wei Hou ◽  
Xue Feng Zhou ◽  
Xiang Chen
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Reinforced Concrete ◽  
Finite Element Model ◽  
Element Model ◽  
Mechanical Behaviors ◽  
Simulation Technology ◽  
Quick Method ◽  
Element Analysis ◽  
Steel Reinforced Concrete

Nonlinear finite element analysis of twelve SRC (steel reinforced concrete) special-shaped columns using ANSYS programs was conducted and the mechanical behaviors of these columns were analyzed. A series of numerical simulation technologies such as defining the material model of the concrete /steel, establishing global finite element model with discrete reinforced bars/stirrups elements and the methods of post-processing of the results were investigated. A quick method of finite element model establishment was proposed to avoid unit not sharing nodes and grid division error during meshing, which would cause problems such as divergence of the model. The results indicate that the numerical simulation technology presented is feasible and can be applied to further research on mechanical behaviors of the SRC structures.

Sign in / Sign up

Export Citation Format

Share Document