scholarly journals Investigation on the High-Temperature Oxidation Resistance of Ni-(3~10) Ta and Ni-(3~10) Y Alloys

Metals ◽  
2019 ◽  
Vol 9 (1) ◽  
pp. 97 ◽  
Author(s):  
Hang Duan ◽  
Yan Liu ◽  
Tiesong Lin ◽  
Hui Zhang ◽  
Zhengren Huang
Keyword(s):  
Oxide Layer ◽  
Oxidation Resistance ◽  
Oxidation Behavior ◽  
Vacancy Concentration ◽  
Mass Gain ◽  
Isothermal Oxidation ◽  
Vacuum Arc ◽  
Oxygen Vacancy Concentration ◽  
Positive Role ◽  
Temperature Oxidation

Ni-(3~10) Ta and Ni-(3~10) Y alloys were fabricated by vacuum arc melting. The oxidation resistance of the alloys was studied by cyclic and isothermal oxidation tests at 800 °C in static air. The present work focused on the investigation of the effects of the alloying elements (Ta and Y) on the oxidation behavior of Ni-based alloys. The oxidation behavior of alloys was evaluated by mass gain, composition, as well as the microstructure of oxidized products. The experimental results indicated that Ta at a low content (3 wt %) had a positive role in enhancing oxidation resistance by decreasing the oxygen vacancy concentration of the oxide layer to prevent the inward diffusion of oxygen during oxidation, and the mass gain decreased from 2.9 mg·cm−2 to 1.7 mg·cm−2 (800 °C/200 h), while Y (3~10 wt %) degraded the oxidation resistance. However, it is worth mentioning that the pinning effect of Y2O3 increased the adhesion between the substrate and oxide layer by changing the growing patterns of the oxide layer from a plane growth to fibrous growth. Among the results, the bonding of the substrate and oxide layer was best in the Ni-3Y alloys.

Improvement in the Oxidation Resistance of β-SiAlON Ceramics Produced from Mechanically Milled Powders

2012 ◽  
Vol 18-19 ◽  
pp. 281-290
Author(s):  
Onur Eser ◽  
S. Kurama
Keyword(s):  
Oxidation Resistance ◽  
High Temperature Oxidation ◽  
Oxidation Behavior ◽  
Oxidation Process ◽  
Isothermal Oxidation ◽  
High Energy ◽  
Particle Sizes ◽  
Temperature Oxidation ◽  
Dry Air ◽  
Milled Powders

In the present study the oxidation behavior of β-SiAlON ceramics, which were produced from conventional and high energy mechanical milled powders, was investigated. High energy mechanically milled powders have lower particle sizes ( 130 nm) than those of conventional powders (216 nm) and fully densified at lower temperatures with less amount of additives. The amount of additive is an important parameter to improve the high temperature oxidation resistance of SiAlON ceramics. The cyclic and isothermal oxidation tests were carried out at 1300 and 1400°C in dry air environment. The weight gain of oxidized samples was measured during the oxidation process. The alteration of oxide layer was analyzed by XRD and SEM. The results indicate that oxidation resistance of the samples produced from mechanically milled powders with less amount of additive is higher than that of conventional one. Therefore, β-SiAlON ceramics which were sintered at 100°C lower temperatures with less amount of additive (3.5 wt. % Y2O3), showed a better oxidation resistance.

Investigating the High Temperature Oxidation Behavior of TiAl-Based Alloys with Nickel and Ruthenium Additions

2014 ◽  
Vol 1019 ◽  
pp. 294-301
Author(s):  
H.C. Mantyi ◽  
L.A. Cornish ◽  
Lesley H. Chown ◽  
I. Alain Mwamba
Keyword(s):  
Room Temperature ◽  
Oxidation Behavior ◽  
Mass Gain ◽  
Isothermal Oxidation ◽  
X Ray Diffraction ◽  
Mechanically Alloyed ◽  
Temperature Oxidation ◽  
X Ray ◽  
High Temperature Oxidation Behavior ◽  
Titanium Aluminium

Pure powders of titanium, aluminium, nickel and ruthenium were mechanically alloyed and melted in a button arc furnace under an argon atmosphere to produce two alloys of composition Ti-52.5Al-10.0Ni (at.%) and Ti-52.5Al-10.0Ni-0.2Ru (at.%). The alloys were then cut and metallographically prepared. Scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDX) and X-ray diffraction (XRD) were used to characterize the samples. Thermogravimetric analysis (TGA) was used to analyze the oxidation behavior from room temperature up to 1050°C. The alloys were also oxidized in air at 1050°C for 120 hours. The Ti-52.5Al-10.0Ni (at.%) alloy formed dendrites of γ-TiAl (55.6 at.% Al) surrounded by a eutectic of γ-TiAl + Al3NiTi2 (τ3) phases. The Ti-52.5Al-10.0Ni-0.2Ru (at.%) alloy formed dendrites of γ-TiAl (53.6 at.% Al) surrounded by a eutectic of γ-TiAl + Al3NiTi2 (τ3). The ruthenium was mostly in solid solution (0.3 at.%) in the Al3NiTi2 (τ3) phase, although traces of it were present in the dendrites (0.1 at.% Ru). When oxidized in air from room temperature to 1050°C, the as-cast Ti-52.5Al-10.0Ni-0.2Ru (at.%) had a mass gain of 0.60% and the as-cast Ti-52.5Al-10.0Ni (at.%) had a mass gain of 0.97%. Isothermal oxidation of both alloys at 1050°C for 120 hours formed mixed metal oxides of TiO2+Al2O3 on the surface.

Phase Constitution and Oxidation Resistance of B2 (Ir, Co)Al

2002 ◽  
Vol 753 ◽  
Author(s):  
Hideki Hosoda ◽  
Hiroshi Noma ◽  
Kenji Wakashima
Keyword(s):  
Oxidation Resistance ◽  
Oxidation Behavior ◽  
Hot Forging ◽  
Isothermal Oxidation ◽  
Oxidation Products ◽  
Phase Constitution ◽  
Temperature Oxidation ◽  
Arc Melting ◽  
Oxidation Resistant ◽  
Ultrahigh Temperature

ABSTRACTB2 iridium aluminide (IrAl) is hopeful for use as an ultrahigh temperature oxidation resistant coating above 1600K. In this study, the effect of Co substitution for Ir on phase constitution, hardness and oxidation behavior was studied for IrAl alloys. Alloys of (Ir, Co)-50mol%Al with various Co contents were fabricated by Ar-arc melting followed by hot-forging at 1773K. Oxidation behavior was evaluated using thermogravimetry (TG) in Ar-67%O2 up to 1823K. XRD and SEM were also carried out for alloy characterization. It was found that a continuous B2 solid solution (Ir,Co)Al is formed between IrAl and CoAl. Depending on the Co concentration, the oxidation products identified after heating to 1873K in Ar-67%O2 were Ir, IrO2 and A2O3 and/or Co2AlO4. Thin and continuous Al2O3 layers were observed after isothermal oxidation at 1673K when Co content is more than 20mol%Co. In this case, the weight change by isothermal oxidation at 1673K becomes higher with decreasing Co content. The (Ir,Co)Al alloys containing 20–40mol%Co exhibit higher oxidation resistance than CoAl and IrAl, and thus oxidation resistance of CoAl is improved by Ir addition.

High Temperature Oxidation Behavior of Al Added Mo / Mo5SiB2in-situ Composites

2004 ◽  
Vol 842 ◽  
Author(s):  
Akira Yamauchi ◽  
Kyousuke Yoshimi ◽  
Shuji Hanada
Keyword(s):  
Oxidation Resistance ◽  
Oxidation Behavior ◽  
Mass Gain ◽  
Protective Oxide ◽  
Initial Oxidation ◽  
Temperature Oxidation ◽  
Temperature Range ◽  
Crystalline Oxides ◽  
Rapid Mass

ABSTRACTIsothermal oxidation behavior of Mo/Mo5SiB2in-situ composites containing small amounts of Al was investigated under an Ar-20%O2 atmosphere in the temperature range of 1073–1673 K. The Mo/Mo5SiB2in-situ composites, (Mo-8.7mol%Si-17.4mol%B)100-xAlx (x=0, 1, 3, and 5mol%), were prepared by Ar arc-melting, and then homogenized at 2073 K for 24 h in an Ar-flow atmosphere. Without addition of Al, Mo/Mo5SiB2in-situ composite exhibits a rapid mass loss at the initial oxidation stage, followed by passive oxidation after the substrate is sealed with borosilicate glass in the temperature range of 1173–1473 K, whereas it exhibits a rapid mass gain around 1073 K. On the other hand, small Al additions, especially of 1 mol%, significantly improve the oxidation resistance of Mo/Mo5SiB2in-situ composites at temperatures from 1073–1573 K. The excellent oxidation resistance is considered to be due to the rapid formation of a continuous, dense scale of Al-Si-O complex oxides. The protective oxide scales contain crystalline oxides, and the amounts of the crystalline oxides obviously increase with Al concentration.

MECHANICAL PROPERTIES AND HIGH TEMPERATURE OXIDATION BEHAVIOR OF Ti–Al COATING REINFORCED BY NITRIDES ON Ti–6Al–4V ALLOY

2016 ◽  
Vol 23 (05) ◽  
pp. 1650031
Author(s):  
JINGJIE DAI ◽  
HUIJUN YU ◽  
JIYUN ZHU ◽  
FEI WENG ◽  
CHUANZHONG CHEN
Keyword(s):  
Mechanical Properties ◽  
Titanium Alloy ◽  
High Temperature ◽  
Oxidation Resistance ◽  
High Temperature Oxidation ◽  
Oxidation Behavior ◽  
Mass Gain ◽  
Temperature Oxidation ◽  
High Temperature Oxidation Behavior ◽  
Al Coating

Ti–Al alloyed coating reinforced by nitrides was fabricated by laser surface alloying technique to improve mechanical properties and high temperature oxidation resistance of Ti–6Al–4V titanium alloy. Microstructures, mechanical properties and high temperature oxidation behavior of the alloyed coating were analyzed. The results show that the alloyed coating consisted of Ti3Al, TiAl2, TiN and Ti2AlN phases. Nitrides with different morphologies were dispersed in the alloyed coating. The maximum microhardness of the alloyed coating was 906[Formula: see text]HV. The friction coefficients of the alloyed coating at room temperature and high temperature were both one-fourth of the substrate. Mass gain of the alloyed coating oxidized at 800[Formula: see text]C for 1000[Formula: see text]h in static air was [Formula: see text][Formula: see text]mg/mm2, which was 1/35th of the substrate. No obvious spallation was observed for the alloyed coating after oxidation. The alloyed coating exhibited excellent mechanical properties and long-term high temperature oxidation resistance, which improved surface properties of Ti–6Al–4V titanium alloy significantly.

High-Temperature Oxidation Behavior of Cu-Si-Y Alloys

2013 ◽  
Vol 32 (4) ◽  
pp. 397-403
Author(s):  
Qun Liu ◽  
Guangyan Fu ◽  
Yong Su ◽  
Zhigang Zhang ◽  
Qi Xiong
Keyword(s):  
Grain Size ◽  
High Temperature ◽  
Oxidation Resistance ◽  
High Temperature Oxidation ◽  
Oxidation Behavior ◽  
Mass Gain ◽  
Alloying Elements ◽  
Experimental Conditions ◽  
Temperature Oxidation ◽  
High Temperature Oxidation Behavior

AbstractThe effect of rare-earth element Y on high-temperature oxidation behavior of Cu-Si alloys at 973 and 1073 K in 0.1 MPa flowing pure O2 has been investigated. Results show at the two temperatures the mass gain of the alloys with different compositions follows the following sequence, Cu-3Si-1.0Y > Cu-3Si-0Y > Cu-3Si-0.5Y alloy. As the Y content increases, the grain size of the alloys decreases, which accelerates the diffusion rate of the alloying elements in the alloys and oxygen under the experimental conditions, increases the ratio of short-path diffusion, and promotes the formation of SiO2 and Y2O3. The three alloys do not form continuous oxide scales of SiO2 or Y2O3, but their rapid formation and dispersed distribution due to the grain-size reduction may also hinder the diffusion of alloying elements and oxygen, which is beneficial to improve the oxidation resistance of the Y-containing alloys. Thereby, the Cu-3Si-0.5Y alloy has good oxidation resistance. The Cu-3Si-1.0Y alloy exhibits largest mass gain among the three alloys, which is due to the fact that in the alloy with higher Y contend and finer grain size, more amount of Y2O3 is more quickly formed, whose mass occupy a more proportion in the whole mass gain of the alloy.

scholarly journals Isothermal Oxidation Behavior of Novel Al2O3 / NiCrAlY / Ti3Al System at 850�C

2020 ◽  
Vol 71 (5) ◽  
pp. 106-116
Author(s):  
Alexandra Banu ◽  
Alexandru Paraschiv ◽  
Simona Petrescu ◽  
Irina Atkinson ◽  
Elena Maria Anghel ◽  
...  
Keyword(s):  
Oxidation Resistance ◽  
Oxidation Behavior ◽  
Mass Gain ◽  
Isothermal Oxidation ◽  
Thermal Barrier ◽  
The Novel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Aerospace Applications

The novel Al2O3 / NiCrAlY /alfa2-Ti3Al system obtained by APS technique was tested against long (500h) isothermal oxidation at 850�C in air for prospective use in aerospace applications. EDX-SEM, X-ray diffraction (XRD) and Raman investigations were conducted to substantiate structural, textural and mass gain modifications underwent by the Al2O3 / NiCrAlY /alfa2-Ti3Al system in comparison with bare alfa2-Ti3Al and NiCrAlY /alfa2-Ti3Al system. Improved oxidation resistance of the double-coated system is based on moderate oxygen and thermal barrier role played by the mixture of delta - and alfa-Al2O3 present in the top ceramic coat.

scholarly journals High-Temperature Oxidation Behavior of a Cu-Bearing 17Cr Ferritic Stainless Steel

Scanning ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Mengqi Zhang ◽  
Ying Han ◽  
Guoqing Zu ◽  
Jiapeng Sun ◽  
Weiwei Zhu ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Weight Gain ◽  
Oxidation Resistance ◽  
Ferritic Stainless Steel ◽  
Oxidation Kinetics ◽  
Oxidation Behavior ◽  
Isothermal Oxidation ◽  
Element Distribution ◽  
Temperature Oxidation ◽  
Good Oxidation Resistance

The isothermal oxidation behavior of 17Cr-0.85Si-0.5Nb-1.2Cu ferritic stainless steel in air was studied from 850°C to 1050°C by analyzing its weight gain after oxidation. The kinetic curves were plotted using the oxidation weight-gain data, and the structure, surface morphology, and element distribution of the oxide films were analyzed by XRD, SEM, and EDS. The results showed that the oxidation kinetics curves at 850°C and 950°C followed a parabolic law, and a continuous and dense oxide film composed of Cr2O3 and MnCr2O4, FeCr2O4, and Cu-Cr rich spinel was formed, which reveals that the steel displayed good oxidation resistance. When the temperature was increased to 1050°C, the oxidation kinetics curves gradually changed from parabolic to linear after 40 h exposure, which indicated that the oxidation resistance significantly worsened. A lower oxidation resistance was observed at 1050°C due to the formation of a large amount of Fe2O3 on the surface and the volatilization of the inner Cr2O3 layer.

scholarly journals Isothermal Oxidation Performance of Laser Cladding Assisted with Preheat (LCAP) Tribaloy T-800 Composite Coatings Deposited on EN8

Coatings ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 843
Author(s):  
Sipiwe Trinity Nyadongo ◽  
Sisa Lesley Pityana ◽  
Eyitayo Olatunde Olakanmi
Keyword(s):  
Iron Oxide ◽  
Composite Coating ◽  
Laser Cladding ◽  
Composite Coatings ◽  
Parabolic Rate Constant ◽  
Mass Gain ◽  
Isothermal Oxidation ◽  
Operational Parameters ◽  
Temperature Oxidation ◽  
Service Environments

It is anticipated that laser cladding assisted with preheat (LCAP)-deposited Tribaloy (T-800) composite coatings enhances resistance to structural degradation upon exposure to elevated-temperature oxidation service environments. The oxidation kinetics of LCAP T-800 composite coatings deposited on EN8 substrate and its mechanisms have not been explored in severe conditions that are similar to operational parameters. The isothermal oxidation behaviour of the T-800 composite coating deposited on EN8 via LCAP was studied at 800 °C in air for up to 120 h (5 × 24 h cycles) and contrasted to that of uncoated samples. The mass gain per unit area of the coating was eight times less than that of the uncoated EN8 substrate. The parabolic rate constant (Kp) for EN8 was 6.72 × 10−12 g2·cm−4·s−1, whilst that for the T-800 composite coating was 8.1 × 10−13 g2·cm−4·s−1. This was attributed to a stable chromium oxide (Cr2O3) layer that formed on the coating surface, thereby preventing further oxidation, whilst the iron oxide film that formed on the EN8 substrate allowed the permeation of the oxygen ions into the oxide. The iron oxide (Fe2O3) film that developed on EN8 spalled, as evidenced by the cracking of oxide when the oxidation time was greater than 72 h, whilst the Cr2O3 film maintained its integrity up to 120 h. A parabolic law was observed by the T-800 composite coating, whilst a paralinear law was reported for EN8 at 800 °C up to 120 h. This coating can be used in turbine parts where temperatures are <800 °C.

Oxidation Behavior of TiAl Based Alloys Prepared by Spark Plasma Sintering

2010 ◽  
Vol 152-153 ◽  
pp. 940-944
Author(s):  
Hua Chen ◽  
Jing Chao Zhang ◽  
X.Y Lu
Keyword(s):  
Mechanical Alloying ◽  
Spark Plasma Sintering ◽  
Oxidation Behavior ◽  
Mass Gain ◽  
Vacuum Sintering ◽  
Temperature Oxidation ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
High Temperature Oxidation Behavior ◽  
Fully Lamellar

The spark plasma sintering (SPS) microstructure and high temperature oxidation behavior of TiH2-45Al-0.2Si-5Nb(at.%) alloy were investigated.Emphasis was placed on the effect of SPS microstructures, obtained by blend powder and mechanical alloying powder. The mass gain due to oxidation was measured using an electro balance. The oxide layers as well as its micro-structure were examined by SEM and EDS, and XRD. The results show that sintered microstructure of blend powder is composed of fully lamellar TiAl/ Ti3Al phase, and that of the mechanical alloying powder is composed of finer granular TiAl/Ti3Al phase. The latter oxidation rate is lower, and forms continuous mixed oxide layer of Al2O3 and TiO2. Both SPS microstructure of blend powder and mechanical alloying powder are superior in oxidation behavior to ordinary vacuum sintering.

Sign in / Sign up

Export Citation Format

Share Document