scholarly journals Ageing Effects on Room-Temperature Tensile Properties and Fracture Behavior of Quenched and Tempered T92/TP316H Dissimilar Welded Joints with Ni-Based Weld Metal

Metals ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 791 ◽  
Author(s):  
Lucia Čiripová ◽  
Ladislav Falat ◽  
Peter Ševc ◽  
Marek Vojtko ◽  
Miroslav Džupon
Keyword(s):  
Weld Metal ◽  
Tensile Properties ◽  
Welded Joints ◽  
Room Temperature ◽  
Thermal Exposure ◽  
Tensile Tests ◽  
Strength Properties ◽  
Air Cooling ◽  
Plastic Properties ◽  
Ageing Effects

The present work is focused on the investigation of isothermal ageing effects on room-temperature tensile properties and the failure of quenched and tempered martensitic/austenitic weldments between T92 and TP316H heat-resistant steels. The dissimilar weldments were produced by gas tungsten arc welding technique using a Ni-based Thermanit Nicro 82 filler metal. The welded joints were subjected to unconventional post-welding heat treatment consisting of the welds solutionizing (1060 °C/30 min), followed by their water quenching and final stabilization tempering (760 °C/60 min). The treatment was completed by spontaneous air cooling within a tempering furnace. The welds in their initial quenched and tempered condition were subsequently aged at 620 °C for up to 2500 h. Apart from room-temperature tensile tests performed for all the welds material states, additional cross-weld hardness measurements were carried out on longitudinal sections of broken tensile specimens. The applied thermal exposure resulted in recognizable deterioration of plastic properties, whereas their effects on strength properties were rather small. The welds tensile straining and fracture evolution exhibited competitive behavior between the austenitic TP316H region and Ni-based weld metal. The observed failure locations showed significant hardness peaks due to intensive, necking-related strain hardening effects occurred during the tensile tests.

scholarly journals The Effects of Electrochemical Hydrogen Charging on Room-Temperature Tensile Properties of T92/TP316H Dissimilar Weldments in Quenched-and-Tempered and Thermally-Aged Conditions

Metals ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 864 ◽  
Author(s):  
Peter Ševc ◽  
Ladislav Falat ◽  
Lucia Čiripová ◽  
Miroslav Džupon ◽  
Marek Vojtko
Keyword(s):  
Hydrogen Embrittlement ◽  
Weld Metal ◽  
Tensile Properties ◽  
Thermal Aging ◽  
Room Temperature ◽  
Dominant Role ◽  
Type Ii ◽  
Plastic Properties ◽  
Hydrogen Charging ◽  
Material State

The influence of isothermal aging at 620 °C in combination with subsequent electrochemical hydrogen charging at room-temperature was studied on quenched-and-tempered T92/TP316H martensitic/austenitic weldments in terms of their room-temperature tensile properties and fracture behavior. Hydrogen charging of the weldments did not significantly affect their strength properties; however, it resulted in considerable deterioration of their plastic properties along with significant impact on their fracture characteristics and failure localization. The hydrogen embrittlement plays a dominant role in degradation of the plastic properties of the weldments already in their initial material state, i.e., before thermal aging. After thermal aging and subsequent hydrogen charging, mutual superposition of thermal and hydrogen embrittlement phenomena had led to clearly observable effects on the welds deformation and fracture processes. The measure of hydrogen embrittlement was clearly lowered for thermally aged material state, since the contribution of thermal embrittlement to overall degradation of the weldments has dominated. The majority of failures of the weldments after hydrogen charging occurred in the vicinity of T92 BM/Ni weld metal (WM) fusion zone; mostly along the Type-II boundary in Ni-based weld metal. Thus, regardless of aging exposure, the most critical failure regions of the investigated weldments after hydrogen charging and tensile straining at room temperature are the T92 BM/Ni WM fusion boundary and Type-II boundary acting like preferential microstructural sites for hydrogen embrittling effects accumulation.

MAGNESIUM ZK61A

Alloy Digest ◽  
1969 ◽  
Vol 18 (10) ◽  
Keyword(s):  
Corrosion Resistance ◽  
Physical Properties ◽  
Tensile Properties ◽  
Room Temperature ◽  
Heat Treating ◽  
Strength Properties ◽  
Casting Alloy ◽  
Chemical Company ◽  
Casting Alloys ◽  
Magnesium Casting

Abstract Magnesium ZK61A is a heat treatable sand casting alloy offering higher strength properties for room-temperature applications than other magnesium casting alloys. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as casting, heat treating, machining, and joining. Filing Code: Mg-67. Producer or source: The Dow Chemical Company.

Effects of Extrusion on the Mechanical Properties and Damping Capacity of Mg-1.8Cu-0.5Mn Alloy

2007 ◽  
Vol 546-549 ◽  
pp. 257-260 ◽  
Author(s):  
Zhen Yan Zhang ◽  
Li Ming Peng ◽  
Xiao Qin Zeng ◽  
Lin Du ◽  
Lan Ma ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Properties ◽  
Room Temperature ◽  
Tensile Tests ◽  
Optical Microscope ◽  
Damping Capacity ◽  
X Ray Diffraction ◽  
Dynamic Mechanical Analyzer ◽  
X Ray ◽  
Solute Atoms

Effects of extrusion on mechanical properties and damping capacity of Mg-1.8wt.%Cu -0.5wt.%Mn (MCM1805) alloy have been investigated. Tensile tests and dynamic mechanical analyzer were respectively used to measure tensile properties and damping capacity at room temperature of as-cast and as-extruded MCM1805 alloy. The microstructure was studied using optical microscope, X-ray diffraction and scanning electron microscope with an energy dispersive X-ray spectrometer. Granato-Lücke model was used to explain the influences of extrusion on damping capacity of MCM1805 alloy. The results showed that extrusion dramatically decreases the grain size but has little influence on phase composition and solute atoms concentration of MCM1805 alloy, and the grain refinement was the dominant reason for the obvious increase of tensile properties and decrease of internal friction of MCM1805 alloy.

Effect of Thermal Exposure on Tensile and Fatigue Properties of Clay Reinforced Nylon Nanocomposites

2015 ◽  
Vol 833 ◽  
pp. 52-55
Author(s):  
Yukiko Nakahara ◽  
Yusuke Kodama ◽  
Shi Jie Zhu ◽  
Arimitsu Usuki ◽  
Makoto Kato
Keyword(s):  
Tensile Strength ◽  
Room Temperature ◽  
Thermal Exposure ◽  
Tensile Tests ◽  
Nylon 6 ◽  
Fatigue Tests ◽  
Fatigue Properties ◽  
Oxidation Treatment ◽  
Exposure Temperature ◽  
Matrix Nanocomposite

In this paper, both nylon 6 and 2 wt% clay reinforced nylon 6 matrix nanocomposite were used for thermal exposure tests at temperatures of 80 oC and 120 oC and 150 oC, respectively. Then, the tensile tests and fatigue tests of the exposed specimens were conducted at room temperature. It was shown that the tensile strength in both nylon 6 and NCH-2 decreased with an increase in thermal exposure temperature. The brittle fracture occurred in the specimens exposed at 120 oC and 150 oC. After pre-oxidation treatment at 80 °C for 100 hours, the fatigue strength decreased 14% in nylon 6, and 8% in NCH-2. From this result, it was understood that the addition of clay in nylon 6 could suppress the decrease of fatigue strengths.

Effect of High Temperature Caliber Rolling on Microstructure and Room Temperature Tensile Properties of Mg-3Al-1Zn (AZ31) Alloy

2013 ◽  
Vol 209 ◽  
pp. 6-9 ◽  
Author(s):  
Rajendra Doiphode ◽  
S.V.S. Narayana Murty ◽  
Nityanand Prabhu ◽  
Bhagwati Prasad Kashyap
Keyword(s):  
Tensile Strength ◽  
High Temperature ◽  
Yield Strength ◽  
Strain Rate ◽  
Tensile Properties ◽  
Room Temperature ◽  
Tensile Tests ◽  
Az31 Alloy ◽  
Rolling Temperature ◽  
Grain Sizes

Mg-3Al-1Zn (AZ31) alloy was caliber rolled at 250, 300, 350, 400 and 450 °C. The effects of caliber rolling temperature on the microstructure and tensile properties were investigated. The room temperature tensile tests were carried out to failure at a strain rate of 1 x 10-4s-1. The nature of stress-strain curves obtained was found to vary with the temperature employed in caliber rolling. The yield strength and tensile strength followed a sinusoidal behaviour with increasing caliber rolling temperature but no such trend was noted in ductility. These variations in tensile properties were explained by the varying grain sizes obtained as a function of caliber rolling temperature.

scholarly journals Assessment of the Effect of Laser Welding on the Properties and Structure of TMCP Steel Butt Joints

Materials ◽  
2020 ◽  
Vol 13 (6) ◽  
pp. 1312 ◽  
Author(s):  
Jacek Górka
Keyword(s):  
Laser Beam ◽  
Welded Joints ◽  
Research Work ◽  
Laser Beam Welding ◽  
Welding Process ◽  
Tensile Tests ◽  
Carbon Equivalent ◽  
Quality Level ◽  
Butt Joints ◽  
Plastic Properties

The research work and related tests aimed to identify the effect of filler metal-free laser beam welding on the structure and properties of butt joints made of steel 700MC subjected to the TMCP (thermo-mechanically controlled processed) process. The tests involved 10-mm thick welded joints and a welding linear energy of 4 kJ/mm and 5 kJ/mm. The inert gas shielded welding process was performed in the flat position (PA) and horizontal position (PC). Non-destructive testing enabled classification of the tested welded joints as representing the quality level B in accordance with the requirements set out in standard 13919-1. Destructive tests revealed that the tensile strength of the joints was 5% lower than S700MC steel. The results of tensile tests and changes in structure were referred to joints made using the MAG (Metal Active Gas) method. The tests of thin films performed using a high-resolution scanning transmission electron microscope revealed that, during laser beam welding, an increase in dilution was accompanied by an increase in the content of alloying microadditions titanium and niobium, particularly in the fusion area. A significant content of hardening phases in the welded joint during cooling led to significant precipitation hardening by fine-dispersive (Ti,Nb)(C,N) type precipitates being of several nanometres in size, which, in turn, resulted in the reduction of plastic properties. An increase in the concentration of elements responsible for steel hardening, i.e., Ti and Nb, also contributed to reducing the weld toughness below the acceptable value, which amounts to 25 J/cm2. In cases of S700MC, the analysis of the phase transformation of austenite exposed to welding thermal cycles and the value of carbon equivalent cannot be the only factors taken into consideration when assessing weldability.

IMPACT TENSILE PROPERTIES OF YAG LASER WELDED BUTT JOINTS MADE BY DIFFERENT STEEL SHEETS FOR VEHICLES

2008 ◽  
Vol 22 (09n11) ◽  
pp. 1712-1717
Author(s):  
Y. TAKAHASHI ◽  
M. DAIMARUYA ◽  
H. KOBAYASHI ◽  
H. TSUDA ◽  
H. FUJIKI
Keyword(s):  
Tensile Properties ◽  
Welded Joints ◽  
Testing Machine ◽  
High Strength ◽  
Tensile Tests ◽  
Butt Joints ◽  
Yag Laser ◽  
Steel Sheets ◽  
Static Tensile ◽  
The Impact

The tensile properties of YAG laser welded butt joints using different high strength steel sheets with a tensile strength of 270 MPa, 590 MPa and 980 MPa (denoted HR270, HR590 and HR980, respectively) were investigated at static and dynamic rates, together with the three kinds of laser welded joints made by the same steel sheets. The impact tensile tests were performed by using the vertical type of split Hopkinson tension bar apparatus, while the static tensile tests were carried out using a universal testing machine INSTRON5586. The impact tensile strengths were significantly increased in comparison with the static ones due to the effect of strain rate, which might be the contribution of the part of HR270 base metal. And in both of static and impact tests, the fracture strains of HR270-HR590 joint, HR270-HR980 joint and HR590-HR980 joint were about one half of the fracture strains observed in the same steel welded joints of HR270-HR270, HR270-HR270 and HR590-HR590, respectively.

Mechanical Behavior After Stress Relaxation in PVDF

2018 ◽  
Author(s):  
Rafael Luis Menezes Freitas ◽  
Celio Costa ◽  
Erica Gervasoni Chaves ◽  
Sylvia Teixeira
Keyword(s):  
Stress Relaxation ◽  
Tensile Properties ◽  
Room Temperature ◽  
Volume Fraction ◽  
Tensile Tests ◽  
Yield Strain ◽  
Cooling Temperature ◽  
Cooling Conditions ◽  
C 23 ◽  
Processing Stress

This study presents the mechanical properties evaluation of two commercial grades of PVDFs, which were extruded with the same parameters but with different cooling temperatures. After processing, stress relaxation with 7% strain was imposed and tensile properties were measured. The cooling temperature after extrusion were 4°C, 23°C and 80°C. Then, the PVDFs were submitted to stress relaxation at 23°C and 7% strain. The as processed and after relaxation samples were characterized by FTIR, XRD, DSC and tensile tests at 23°C. The stress relaxation at 23 °C resulted in no change in volume fraction of crystallinity for PVDF A and B. The XRD and FTIR, for both PVDFs, showed that the crystalline phases were the same, for all cooling conditions and did not change after the stress relaxation. The tensile properties at room temperature showed that the yield stress was a little affect by the cooling temperature, while Young’s Modulus and yield strain were insensible to the cooling temperature. After the stress relaxation, these three tensile properties were slightly affected for both grades.

scholarly journals Investigation of Slow Eutectoid Element on Tensile Properties and Superplasticity of a Forged SP700 Titanium Alloy

Metals ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 1852
Author(s):  
Dong Han ◽  
Yongqing Zhao ◽  
Weidong Zeng ◽  
Junfeng Xiang
Keyword(s):  
Tensile Properties ◽  
Room Temperature ◽  
Rate Sensitivity ◽  
Tensile Tests ◽  
Microstructure Characteristics ◽  
Density Of Dislocations ◽  
Globular Microstructure ◽  
Β Phase ◽  
Elevated Temperature Tensile ◽  
Cr Addition

The tensile properties and superplasticity of a forged SP700 alloy with slow eutectoid element (1.5%Cr) addition were investigated in the present paper. The results of the microstructures showed that slow eutectoid element Cr has a significant influence on stabilizing the β phase and the SP700Cr alloy showed a uniform duplex and completely globular microstructure after annealing at 820 °C for 1 h and aging at 500 °C for 6 h. The results of the tensile tests showed that the yield strength, ultimate tensile strength and elongation of the alloy with optimized microstructure were 1312 MPa, 1211 MPa and 10% at room temperature, and the elongation was achieved to 1127% at 770 °C. Compared with that of the SP700 alloy, the strain rate sensitivity of the SP700Cr alloy showed a higher value. The microstructures after elevated temperature tensile tests showed that the higher density of dislocations and twins exists in SP700 alloy and the lower density of dislocations favor distribution in SP700Cr alloy. Based on the above results, the tensile properties and superplasticity of the forged SP700 alloy with 1.5% Cr addition was analyzed. In addition, microstructure characteristics were investigated by the TEM and EBSD technologies.

Laboratory Controlled Rolling of Microalloyed Steel for Production of Seamless Tubes

2016 ◽  
Vol 258 ◽  
pp. 611-614 ◽  
Author(s):  
Petr Kawulok ◽  
Radek Jurča ◽  
Ivo Schindler ◽  
Stanislav Rusz ◽  
Rostislav Turoň ◽  
...  
Keyword(s):  
Wall Thickness ◽  
Hsla Steel ◽  
Tensile Tests ◽  
Strength Properties ◽  
Controlled Rolling ◽  
Rolling Temperature ◽  
Plastic Properties ◽  
Finish Rolling Temperature ◽  
Finish Rolling ◽  
Rolling Temperatures

Using the laboratory rolling mill with smooth rolls, piercing, as well as rolling in a pilger mill of the seamless tubes with diameter 273 mm from the HSLA steel microalloyed with vanadium steel was simulated. Influence of the wall thickness (6.3 – 40 mm) and finish rolling temperature on the final structural and mechanical properties was investigated. Necessary temperatures of the phase transformations in the course of cooling were determined by dilatometric tests. Based on the dilatometry results, finish rolling temperatures were reduced. Lower rolling temperatures yielded in a relative grain refinement. Effect of the finish rolling temperature did not have any marked impact on the tensile tests results. Strength properties decreased only slightly with the increasing wall thickness and the plastic properties were not influenced significantly by this parameter. The positive effect of the reduced finishing temperature appeared markedly in the results of impact tests performed at room temperature only. Notch toughness was increased by approx. 25 % in the case of the wall thickness of not less than 20 mm.

Sign in / Sign up

Export Citation Format

Share Document