scholarly journals Effect of Build Orientation on the Microstructure, Mechanical and Corrosion Properties of a Biodegradable High Manganese Steel Processed by Laser Powder Bed Fusion

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 944
Author(s):  
Martin Otto ◽  
Stefan Pilz ◽  
Annett Gebert ◽  
Uta Kühn ◽  
Julia Hufenbach
Keyword(s):  
Electron Backscatter Diffraction ◽  
Longitudinal Axis ◽  
Manganese Steel ◽  
Compressive Yield Strength ◽  
Powder Bed Fusion ◽  
Compression Tests ◽  
Laser Powder Bed Fusion ◽  
Corrosion Properties ◽  
Powder Bed ◽  
Manufacturing Technologies

In the last decade, additive manufacturing technologies like laser powder bed fusion (LPBF) have emerged strongly. However, the process characteristics involving layer-wise build-up of the part and the occurring high, directional thermal gradient result in significant changes of the microstructure and the related properties compared to traditionally fabricated materials. This study presents the influence of the build direction (BD) on the microstructure and resulting properties of a novel austenitic Fe‑30Mn‑1C‑0.02S alloy processed via LPBF. The fabricated samples display a {011} texture in BD which was detected by electron backscatter diffraction. Furthermore, isolated binding defects could be observed between the layers. Quasi-static tensile and compression tests displayed that the yield, ultimate tensile as well as the compressive yield strength are significantly higher for samples which were built with their longitudinal axis perpendicular to BD compared to their parallel counterparts. This was predominantly ascribed to the less severe effects of the sharp-edged binding defects loaded perpendicular to BD. Additionally, a change of the Young’s modulus in dependence of BD could be demonstrated, which is explained by the respective texture. Potentiodynamic polarization tests conducted in a simulated body fluid revealed only slight differences of the corrosion properties in dependence of the build design.

scholarly journals Corrosion Fatigue Characteristics of 316L Stainless Steel Fabricated by Laser Powder Bed Fusion

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1046
Author(s):  
Balachander Gnanasekaran ◽  
Jie Song ◽  
Vijay Vasudevan ◽  
Yao Fu
Keyword(s):  
Fatigue Crack ◽  
Crack Propagation ◽  
Fatigue Crack Propagation ◽  
Corrosion Fatigue ◽  
Fatigue Properties ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Corrosion Properties ◽  
Powder Bed ◽  
Fatigue Characteristics

Laser powder bed fusion (LPBF) has been increasingly used in the fabrication of dense metallic structures. However, the corrosion related properties of LPBF alloys, in particular environment-assisted cracking, such as corrosion fatigue properties, are not well understood. In this study, the corrosion and corrosion fatigue characteristics of LPBF 316L stainless steels (SS) in 3.5 wt.% NaCl solution have been investigated using an electrochemical method, high cycle fatigue, and fatigue crack propagation testing. The LPBF 316L SSs demonstrated significantly improved corrosion properties compared to conventionally manufactured 316L, as reflected by the increased pitting and repassivation potentials, as well as retarded crack initiation. However, the printing parameters did not strongly affect the pitting potentials. LPBF samples also demonstrated enhanced capabilities of repassivation during the fatigue crack propagation. The unique microstructural features introduced during the printing process are discussed. The improved corrosion and corrosion fatigue properties are attributed to the presence of columnar/cellular subgrains formed by dislocation networks that serve as high diffusion paths to transport anti-corrosion elements.

scholarly journals Effects of Positioning Conditions on Material Properties In Powder bed Fusion Additive Manufacturing

2021 ◽  
Author(s):  
Mevlüt Yunus Kayacan ◽  
Nihat Yılmaz
Keyword(s):  
Additive Manufacturing ◽  
Material Properties ◽  
Layer By Layer ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Cooling Rates ◽  
Powder Bed ◽  
Manufacturing Technologies ◽  
Average Size ◽  
Hardness Values

Abstract Among additive manufacturing technologies, Laser Powder Bed Fusion (L-PBF) is considered the most widespread layer-by-layer process. Although the L-PBF, which is also called as SLM method, has many advantages, several challenging problems must be overcome, including part positioning issues. In this study, the effect of part positioning on the microstructure of the part in the L-PBF method was investigated. Five Ti6Al4V samples were printed in different positions on the building platform and investigated with the aid of temperature, porosity, microstructure and hardness evaluations. In this study, martensitic needles were detected within the microstructure of Ti6Al4V samples. Furthermore, some twins were noticed on primary martensitic lines and the agglomeration of β precipitates was observed in vanadium rich areas. The positioning conditions of samples were revealed to have a strong effect on temperature gradients and on the average size of martensitic lines. Besides, different hardness values were attained depending on sample positioning conditions. As a major result, cooling rates were found related to positions of samples and the location of point on the samples. Higher cooling rates and repetitive cooling cycles resulted in microstructures becoming finer and harder.

Microstructure and corrosion properties of sensitized laser powder bed fusion printed Inconel 718 to dissolve support structures in a self-terminating manner

2019 ◽  
Vol 27 ◽  
pp. 526-532
Author(s):  
Christopher S. Lefky ◽  
Thomas G. Gallmeyer ◽  
Senthamilaruvi Moorthy ◽  
Aaron Stebner ◽  
Owen J. Hildreth
Keyword(s):  
Inconel 718 ◽  
Powder Bed Fusion ◽  
Support Structures ◽  
Laser Powder Bed Fusion ◽  
Corrosion Properties ◽  
Powder Bed

Mechanical, thermal, and corrosion properties of Cu-10Sn alloy prepared by laser-powder-bed-fusion additive manufacturing

2020 ◽  
Vol 35 ◽  
pp. 101411 ◽  
Author(s):  
Congyuan Zeng ◽  
Bin Zhang ◽  
Ali Hemmasian Ettefagh ◽  
Hao Wen ◽  
Hong Yao ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Corrosion Properties ◽  
Powder Bed

Microstructure of In738Lc Fabricated Using Laser Powder Bed Fusion Additive Manufacturing

2021 ◽  
pp. 1-19
Author(s):  
Nandana Menon ◽  
Tanjheel Hasan Mahdi ◽  
Amrita Basak
Keyword(s):  
Additive Manufacturing ◽  
Electron Backscatter Diffraction ◽  
Small Scale ◽  
Second Phase ◽  
Face Centered Cubic ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Nickel Base Superalloys ◽  
Nickel Base

Abstract Nickel-base superalloys are extensively used in the production of gas turbine hot-section components as they offer exceptional creep strength and superior fatigue resistance at high temperatures. Such improved properties are due to the presence of precipitate-strengthening phases such as Ni3Ti or Ni3Al (gγ phases) in the normally face-centered cubic (FCC) structure of the solidified nickel. Although this second phase is the main reason for the improvements in properties, the presence of such phases also results in increased processing difficulties as these alloys are prone to crack formation. In this work, specimens of IN738LC are fabricated on a Coherent Creator laser powder bed fusion (L-PBF) additive manufacturing (AM) equipment. Optical microscopy (OM), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), and X-Ray diffraction (XRD) are carried out to characterize the deposit region. Metallurgical continuity is achieved in the entire deposit region and the specimens do not show any warpage. However, the specimens show voids (e.g., pores and cracks) in the deposit region. The results show that the percentage void area decreases along the build height direction. The deposited IN738LC shows polycrystalline grains in the entire deposit region as confirmed by XRD and EBSD. The grain size also shows variations along the build direction. In summary, the results open opportunities for academic researchers and small scale businesses in fabricating high-gγ nickel-base superalloys on a desktop laser powder bed fusion AM equipment

scholarly journals Effect of Laser Energy Density on the Microstructure andTexture Evolution of Hastelloy-X Alloy Fabricated by Laser Powder Bed Fusion

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4305
Author(s):  
Shuzhe Zhang ◽  
Yunpei Lei ◽  
Zhen Chen ◽  
Pei Wei ◽  
Wenjie Liu ◽  
...  
Keyword(s):  
Grain Size ◽  
Energy Density ◽  
Electron Backscatter Diffraction ◽  
Laser Energy ◽  
Primary Dendrite ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Hastelloy X ◽  
Powder Bed ◽  
Average Grain Size

It is of great importance to study the microstructure and textural evolution of laser powder bed fusion (LPBF) formed Hastelloy-X alloys, in order to establish a close relationship between the process, microstructure, and properties through the regulation of the Hastelloy-X formation process parameters. In this paper, components of a Hastelloy-X alloy were formed with different laser energy densities (also known as the volume energy density VED). The densification mechanism of Hastelloy-X was studied, and the causes of defects, such as pores and cracks, were analyzed. The influence of different energy densities on grain size, texture, and orientation was investigated using an electron backscatter diffraction technique. The results show that the average grain size, primary dendrite arm spacing, and number of low angle grain boundaries increased with the increase of energy density. At the same time, the VED can strengthen the texture. The textural intensity increases with the increase of energy density. The best mechanical properties were obtained at the VED of 96 J·mm−3.

Sign in / Sign up

Export Citation Format

Share Document