scholarly journals Observation of Vapor Plume Behavior and Process Stability at Single-Track and Multi-Track Levels in Laser Powder Bed Fusion Regime

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 937
Author(s):  
Hang Zheng ◽  
You Wang ◽  
Yinkai Xie ◽  
Shengkun Yang ◽  
Rui Hou ◽  
...  
Keyword(s):  
High Speed ◽  
Powder Bed Fusion ◽  
Single Track ◽  
Laser Powder Bed Fusion ◽  
Process Stability ◽  
Heat Accumulation ◽  
Powder Bed ◽  
Metal Parts ◽  
Vapor Plume ◽  
Track Formation

Laser powder bed fusion (LPBF) is a promising additive manufacturing technology for producing metal parts with complex geometric features. However, the issue concerning process stability and repeatability still hinders its future acceptance by the industry. Gaining a better understanding of the behavior and stability of the evaporation process is an important step towards further insights into the complex interaction between laser and material. In this study, we used off-axis high-speed camera to observe vapor plume evolution in single-track formation on bare Ti-6Al-4V plates; the results showed that evaporation has a strong effect on melting quality even if the keyhole is not developed. We then expanded the experiments to multi-track level and found that the melting mode can change as the result of heat accumulation. The results show the possibility that keyhole regime may be reached even if it starts with a combination of parameters below the threshold for keyhole formation in single-track-level observation.

Measurement of the Melt Pool Length During Single Scan Tracks in a Commercial Laser Powder Bed Fusion Process

2017 ◽  
Author(s):  
J. C. Heigel ◽  
B. M. Lane
Keyword(s):  
Laser Power ◽  
High Speed ◽  
Infrared Camera ◽  
Powder Bed Fusion ◽  
Single Track ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Melt Pool ◽  
Significant Difference ◽  
Scan Speed

This work presents high speed thermographic measurements of the melt pool length during single track laser scans on nickel alloy 625 substrates. Scans are made using a commercial laser powder bed fusion machine while measurements of the radiation from the surface are made using a high speed (1800 frames per second) infrared camera. The melt pool length measurement is based on the detection of the liquidus-solidus transition that is evident in the temperature profile. Seven different combinations of programmed laser power (49 W to 195 W) and scan speed (200 mm/s to 800 mm/s) are investigated and numerous replications using a variety of scan lengths (4 mm to 12 mm) are performed. Results show that the melt pool length reaches steady state within 2 mm of the start of each scan. Melt pool length increases with laser power, but its relationship with scan speed is less obvious because there is no significant difference between cases performed at the highest laser power of 195 W. Although keyholing appears to affect the anticipated trends in melt pool length, further research is required.

Measurement of the Melt Pool Length During Single Scan Tracks in a Commercial Laser Powder Bed Fusion Process

2018 ◽  
Vol 140 (5) ◽  
Author(s):  
J. C. Heigel ◽  
B. M. Lane
Keyword(s):  
Laser Power ◽  
High Speed ◽  
Infrared Camera ◽  
Powder Bed Fusion ◽  
Single Track ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Melt Pool ◽  
Significant Difference ◽  
Scan Speed

This work presents high-speed thermographic measurements of the melt pool length during single track laser scans on nickel alloy 625 substrates. Scans are made using a commercial laser powder bed fusion (PBF) machine while measurements of the radiation from the surface are made using a high speed (1800 frames per second) infrared camera. The melt pool length measurement is based on the detection of the liquidus–solidus transition that is evident in the temperature profile. Seven different combinations of programmed laser power (49–195 W) and scan speed (200–800 mm/s) are investigated, and numerous replications using a variety of scan lengths (4–12 mm) are performed. Results show that the melt pool length reaches steady-state within 2 mm of the start of each scan. Melt pool length increases with laser power, but its relationship with scan speed is less obvious because there is no significant difference between cases performed at the highest laser power of 195 W. Although keyholing appears to affect the anticipated trends in melt pool length, further research is required.

scholarly journals Process characterization and analysis of ceramic powder bed fusion

2021 ◽  
Author(s):  
Kevin Florio ◽  
Dario Puccio ◽  
Giorgio Viganò ◽  
Stefan Pfeiffer ◽  
Fabrizio Verga ◽  
...  
Keyword(s):  
High Speed ◽  
Ceramic Powder ◽  
Integrating Sphere ◽  
Alumina Powder ◽  
Powder Bed Fusion ◽  
Single Track ◽  
Ceramic Powders ◽  
Pure Alumina ◽  
Powder Bed ◽  
Melt Pool

AbstractPowder bed fusion (PBF) of ceramics is often limited because of the low absorptance of ceramic powders and lack of process understanding. These challenges have been addressed through a co-development of customized ceramic powders and laser process capabilities. The starting powder is made of a mix of pure alumina powder and alumina granules, to which a metal oxide dopant is added to increase absorptance. The performance of different granules and process parameters depends on a large number of influencing factors. In this study, two methods for characterizing and analyzing the PBF process are presented and used to assess which dopant is the most suitable for the process. The first method allows one to analyze the absorptance of the laser during the melting of a single track using an integrating sphere. The second one relies on in-situ video imaging using a high-speed camera and an external laser illumination. The absorption behavior of the laser power during the melting of both single tracks and full layers is proven to be a non-linear and extremely dynamic process. While for a single track, the manganese oxide doped powder delivers higher and more stable absorptance. When a full layer is analyzed, iron oxide-doped powder is leading to higher absorptance and a larger melt pool. Both dopants allow the generation of a stable melt-pool, which would be impossible with granules made of pure alumina. In addition, the present study sheds light on several phenomena related to powder and melt-pool dynamics, such as the change of melt-pool shape and dimension over time and powder denudation effects.

scholarly journals In Situ Analysis of Laser Powder Bed Fusion Using Simultaneous High-Speed Infrared and X-ray Imaging

JOM ◽  
2020 ◽  
Vol 73 (1) ◽  
pp. 201-211 ◽  
Author(s):  
Benjamin Gould ◽  
Sarah Wolff ◽  
Niranjan Parab ◽  
Cang Zhao ◽  
Maria Cinta Lorenzo-Martin ◽  
...  
Keyword(s):  
High Speed ◽  
In Situ Analysis ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
X Ray ◽  
X Ray Imaging
Sign in / Sign up

Export Citation Format

Share Document