scholarly journals MEROS Dust Quality of Different Plants and Its Potential Further Uses

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 840
Author(s):  
Claudia Hledik ◽  
Martin Goetz ◽  
Franz Ottner ◽  
Maria Fürhacker
Keyword(s):  
Heavy Metals ◽  
Suspended Solids ◽  
Fine Particles ◽  
Sinter Plant ◽  
Treatment Options ◽  
Blast Furnaces ◽  
Sintering Process ◽  
Furnace Process ◽  
Low Levels

Sintering is a process of agglomeration of fine particles into porous sinters for blast furnaces. During the sintering process, high volumes of sinter plant gas containing high loads of dust, SO2 and NOX and toxic pollutants, such as heavy metals (e.g., Hg, Pb, Cr and Cd) and PCDD/F, are emitted. The objective of this study was to characterize dusts of different plants as the basis for suggestions of reutilization and treatment options. Dusts, eluates and residues were produced and DOC, T-N, ions and heavy metals were analyzed. The results show that dusts from different plants are very similar in terms of DOC, T-N, Mg, Ca and many heavy metals and only differ in criteria such as suspended solids and ions such as K, Na, Cl and SO4. Based on the high levels of alkalis and low levels of iron, direct recycling into the sinter or furnace process is not recommended. The dissolution of the soluble substances in water reduces the MEROS dust by 90% of the weight and extracts the alkalis. The remaining wastewater needs to be treated to reduce DOC, T-N and some heavy metals. The solid residues can be recycled into the sinter to reduce potential PCDD/F, which are attached to the activated carbon.

scholarly journals EFFECTS OF DREDGING ON DOWNSTREAM WATER QUALITY: EKOLE CREEK, NIGERIA

2021 ◽  
Vol 8 (12) ◽  
pp. 17-25
Author(s):  
Opololaoluwa Oladimarum Ogunlowo ◽  
Churchill Ebinimitei Simon
Keyword(s):  
Heavy Metals ◽  
Water Quality ◽  
Electrical Conductivity ◽  
Drinking Water ◽  
Suspended Solids ◽  
Total Dissolve Solid ◽  
Total Suspended Solids ◽  
Negative Effects ◽  
Downstream User

Water is essential part of ecosystem, so its quality must be ascertained for use especially in Ekole creek of Nigeria where dredging activities is heavy, hence this study examined the dredging effect on the downstream water quality of Ekole creek. Water samples were collected from four points which are; Upstream, Dredge I, Dredge II, and Downstream points. The parameters of the water quality determined showed that Turbidity and Total Suspended Solids (TSS) were higher at the Downstream point with values of 31 NTU and 1664 mg/l respectively; pH was also slightly acidic (6.61); but low in Total Dissolve Solid (TDS), Electrical Conductivity,  Nitrate (NO3) and Dissolved Oxygen (DO), as compare to the Upstream. The values of the  heavy metals like Pb (3.845 mg/l), Cr (0.612 mg/l) Ni (0.104 mg/l) and Cu (0.128 mg/l),  at Downstream point, were above Pb (3.0605 mg/l), Cr (0.0 mg/l), Ni (0.017 mg/l) and Cu (0.102 mg/l) of  the Upstream point,before the Dredging points I and II, that have  correlative matrix of(Pb>Fe>Mn>Zn>Cu>Ni>Cr) and  Pb>Fe>Cr>Mn>Zn>Cu>Ni Downstream point. Is discovered the Downstream water is slightly acidic, high in Turbidity and TSS, but low in TDS, EC, NO3 and DO, as against the WHO drinking-water quality, due the effect of dredging on the water quality of the Ekole Creek. It is inferred that the dredging activities have negative effects on the water quality, which can be hazardous to the health of downstream user, and distort the ecosystem; therefore the commercial dredging activities should be checked in Ekole creek.

scholarly journals Performance evaluation of a sediment control pond

2021 ◽  
Author(s):  
Lindsay Pyatt
Keyword(s):  
Heavy Metals ◽  
Water Quality ◽  
Performance Evaluation ◽  
Suspended Solids ◽  
Management Practices ◽  
Fine Particles ◽  
Oxygen Demand ◽  
Quality Parameters ◽  
Design Criteria ◽  
Sediment Control

Current erosion and sediment control practices include the use of sediment control ponds that are designed using the 1994 Ministry of the Environment (MOE) Stormwater Management Practices and Design Manual. These design criteria aim at reducing pollutant loads from developed areas. However, the effectiveness of these design criteria when used for areas undergoing construction has yet to be determined in the field. Thus, this thesis is a performance evaluation of a sediment control pond that was designed using the 1994 MOE stormwater design criteria. The objectives of this thesis include the characterization of the runoff and sediments entering, depositing, and leaving the sediment control pond during the construction phase, and the evaluation of the sediment removal efficiencies of the pond. Generally, the pond was successful in reducing many of the pollutants transported to the pond from the catchment area. Suspended solids were the primary pollutants monitored. Heavy metals and general water quality parameters such as chemical oxygen demand, pH, and alkalinity were also monitored. Suspended solids concentrations were high exiting the pond during several events. The particle size distribution predominantly consisted of fine particles. Most heavy metals including beryllium, cadmium, lead, and nickel were reduced in concentration to levels under their Provincial Water Quality Objectives (PWQO). However, some heavy metals had concentrations above their PWQO when exiting the pond.

scholarly journals Performance evaluation of a sediment control pond

2021 ◽  
Author(s):  
Lindsay Pyatt
Keyword(s):  
Heavy Metals ◽  
Water Quality ◽  
Performance Evaluation ◽  
Suspended Solids ◽  
Management Practices ◽  
Fine Particles ◽  
Oxygen Demand ◽  
Quality Parameters ◽  
Design Criteria ◽  
Sediment Control

Current erosion and sediment control practices include the use of sediment control ponds that are designed using the 1994 Ministry of the Environment (MOE) Stormwater Management Practices and Design Manual. These design criteria aim at reducing pollutant loads from developed areas. However, the effectiveness of these design criteria when used for areas undergoing construction has yet to be determined in the field. Thus, this thesis is a performance evaluation of a sediment control pond that was designed using the 1994 MOE stormwater design criteria. The objectives of this thesis include the characterization of the runoff and sediments entering, depositing, and leaving the sediment control pond during the construction phase, and the evaluation of the sediment removal efficiencies of the pond. Generally, the pond was successful in reducing many of the pollutants transported to the pond from the catchment area. Suspended solids were the primary pollutants monitored. Heavy metals and general water quality parameters such as chemical oxygen demand, pH, and alkalinity were also monitored. Suspended solids concentrations were high exiting the pond during several events. The particle size distribution predominantly consisted of fine particles. Most heavy metals including beryllium, cadmium, lead, and nickel were reduced in concentration to levels under their Provincial Water Quality Objectives (PWQO). However, some heavy metals had concentrations above their PWQO when exiting the pond.

Surgery for Lung Cancer and the Consequences for the Swallow

2016 ◽  
Vol 1 (13) ◽  
pp. 162-168
Author(s):  
Pippa Hales ◽  
Corinne Mossey-Gaston
Keyword(s):  
Lung Cancer ◽  
Treatment Options ◽  
Vocal Cord Palsy ◽  
Subsequent Treatment ◽  
Physiological Reserve ◽  
Palliative Phase ◽  
And Function ◽  
The Impact ◽  
Swallow Function

Lung cancer is one of the most commonly diagnosed cancers across Northern America and Europe. Treatment options offered are dependent on the type of cancer, the location of the tumor, the staging, and the overall health of the person. When surgery for lung cancer is offered, difficulty swallowing is a potential complication that can have several influencing factors. Surgical interaction with the recurrent laryngeal nerve (RLN) can lead to unilateral vocal cord palsy, altering swallow function and safety. Understanding whether the RLN has been preserved, damaged, or sacrificed is integral to understanding the effect on the swallow and the subsequent treatment options available. There is also the risk of post-surgical reduction of physiological reserve, which can reduce the strength and function of the swallow in addition to any surgery specific complications. As lung cancer has a limited prognosis, the clinician must also factor in the palliative phase, as this can further increase the burden of an already compromised swallow. By understanding the surgery and the implications this may have for the swallow, there is the potential to reduce the impact of post-surgical complications and so improve quality of life (QOL) for people with lung cancer.

Raynaud’s phenomenon and digital ischaemia - pharmacologic approach and alternative treatment options

VASA ◽  
2016 ◽  
Vol 45 (3) ◽  
pp. 201-212 ◽  
Author(s):  
Birgit Linnemann ◽  
Matthias Erbe
Keyword(s):  
Quality Of Life ◽  
Angiotensin Receptor Blockers ◽  
Raynaud’S Phenomenon ◽  
Treatment Options ◽  
Raynaud's Phenomenon ◽  
Tissue Loss ◽  
Receptor Antagonists ◽  
Skin Ulcers ◽  
Digital Ischaemia

Abstract. The primary goal of therapy is to reduce the frequency and intensity of Raynaud’s attacks and to minimize the related morbidity rather than to cure the underlying condition. Treatment strategies depend on whether Raynaud’s phenomenon (RP) is primary or secondary. All patients should be instructed about general measures to maintain body warmth and to avoid triggers of RP attacks. Pharmacologic intervention can be useful for patients with severe and frequent RP episodes that impair the patient’s quality of life. Calcium channel blockers are currently the most prescribed and studied medications for this purpose. There has been limited evidence for the efficacy of alpha-1-adrenergic receptor antagonists, angiotensin receptor blockers, topical nitrates or fluoxetine to treat RP. The intravenously administered prostacyclin analogue iloprost can reduce the frequency and severity of RP attacks and is considered a second-line therapy in patients with markedly impaired quality of life, critical digital ischaemia and skin ulcers who are at risk for substantial tissue loss and amputation. Phosphodiesterase inhibitors (e.g., sildenafil) can also improve RP symptoms and ulcer healing whereas endothelin-1 receptor antagonists (e.g., bosentan) are mainly considered treatment options in secondary prevention for patients with digital skin ulcers related to systemic sclerosis. However, their use in clinical practice has been limited by their high cost. Antiplatelet therapy with low-dose aspirin is recommended for all patients who suffer from secondary RP due to ischaemia caused by structural vessel damage. Anticoagulant therapy can be considered during the acute phase of digital ischaemia in patients with suspected vascular occlusive disease attributed to the occurrence of new thromboses. In patients with critical digital ischaemia, consideration should be given to hospitalisation, optimisation of medical treatment in accordance with the underlying disease and evaluation for a secondary, possibly reversible process that is causing or aggravating the clinical symptoms.

Агрономическая эффективность промышленной (голландской) технологии возделывания картофеля

2018 ◽  
Author(s):  
C. Coy ◽  
A.V. Shuravilin ◽  
O.A. Zakharova
Keyword(s):  
Heavy Metals ◽  
Regression Analysis ◽  
Positive Response ◽  
Growth Yield ◽  
Correlation And Regression Analysis ◽  
Yield And Quality ◽  
Quality Of Products ◽  
High Degree ◽  
The Impact

Приведены результаты исследований по изучению влияния промышленной технологии возделывания картофеля на развитие, урожайность и качество продукции. Выявлена положительная реакция растений на подкормку K2SO4 в период посадки. Корреляционно-регрессионный анализ урожайности и качества клубней выявил высокую степень достоверности результатов опыта. Содержание нитратов и тяжелых металлов в клубнях было ниже допустимых величин.The results of studies on the impact of industrial technology of potato cultivation on growth, yield and quality of products. There was a positive response of plants to fertilizer K2SO4 in the period of planting. Correlation and regression analysis of yield and quality of tubers revealed a high degree of reliability of the results of experience. The contents of nitrates and heavy metals in tubers was below the permissible values.

Determination of Traces Heavy Metals from Solid Residues Formed by Combustion of Lignite in Relation to Degree of Accessibility in Soil and Plants

2017 ◽  
Vol 68 (10) ◽  
pp. 2363-2366
Author(s):  
Delia Nica Badea
Keyword(s):  
Heavy Metals ◽  
Power Plant ◽  
Thermal Power ◽  
Reference Value ◽  
Combustion Products ◽  
Toxic Heavy Metals ◽  
Area Of Influence ◽  
Risk Potential

The paper evaluates the presence and content of traces of heavy metals Hg, Pb, Ni, Cd (total forms) from coal and solid combustion products, the degree of transfer and accessibility in the area of influence of a lignite power plant. The content of toxic heavy metals in residues are characterized by RE Meiji [ 1 (Pb and Hg) and REMeij �1 (Ni and Cd) for the filter ash. Pb and Ni content in the soil exceeds normal values, and Pb exceeds and alert value for sensitive soils around the residue deposit (70.20 mg.Kg-1). The degree of accessibility of the metals in plants (TF), reported at the Khan reference value (0.5), indicates a significant bioaccumulation level for the metals: Cd (1.9) and Hg (0.6) inside the deposit; Cd (0.39) at the base of the deposit, Hg (0.8) in the area of the thermal power plant. The trace levels of heavy metals analyzed by GFAAS and CVAAS (Hg), indicates a moderate risk potential for food safety and quality of life in the studied area.

Performance Analysis of the Rotating Biological Contactor Process Based on Particle Fraction and Improvement of Final Effluent Quality

1991 ◽  
Vol 23 (7-9) ◽  
pp. 1457-1466 ◽  
Author(s):  
Kazuhiro Tanaka ◽  
Minoru Tada ◽  
Mitsuo Ito ◽  
Noritugu Shimizu
Keyword(s):  
Suspended Solids ◽  
Fine Particles ◽  
Wastewater Treatment Plants ◽  
Small Scale ◽  
Particle Fraction ◽  
Effluent Quality ◽  
Rotating Biological Contactors ◽  
Activated Sludge Processes ◽  
Fraction Method ◽  
Final Effluent

Biofilm processes are, in general, suitable for small-scale wastewater treatment plants. However, final effluent qualities of biofilm processes are not as good as those of activated sludge processes due to fine particles remaining in the effluents. To improve the effluent qualities of the Rotating Biological Contactors (RBC) process, the behavior of fine particles through the process and the removal of fine particles with solids-liquid separation methods, rapid filtration and coagulation-filtration, were investigated using the particle fraction method. The results are as follows:–An increase of the hydraulic retention time (HRT) in the RBC reactor reduced the amount of fine particles and increased the amount of coarse suspended solids of 44 µm or more in diameter, which are easily removed by clarification. Thus, the final effluent qualities were improved by the increase of HRT.–Suspended solids in effluent from the RBC process at the standard loading are so fine that improvement of the quality is not expected by only lowering the overflow rate of a final clarifier. In contrast, rapid filtration or a coagulation-filtration process is effective. The supended solid concentration and transparency of the effluent from the final clarifier was improved by a factor of two to four, and then BOD of the final effluent was removed by 40-85%.

Variations in Mineral/heavy metals profiling and preventive role of trichomes in Peach Fruits treated with CaC2

2020 ◽  
Vol 23 ◽  
Author(s):  
Muhammad Irfan ◽  
Safdar Abbas ◽  
Beenish Jehan Azhar ◽  
Shakeel Ahmad ◽  
Hafsa Muhammad ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Nutritional Value ◽  
Fine Powder ◽  
Calcium Carbide ◽  
Control Group ◽  
Tandem Accelerator ◽  
Health Promoting ◽  
Elemental Profiling

Background: Phytonutrients in peach fruits have health promoting antioxidants against various chronic diseases. However, there is no extensive data to show the nutritional values of Local peach cultivars after post-harvest treatments. Objective: Mainly this study was objective to determine the effect of calcium carbide on nutritional value and quality of fruits of Pakistani peach cultivars. Methods: The peach fruits were collected from three different peach orchids of KPK and the fruits were divided into 4 groups while 5th group was collected from local fruit shop. Each experimental group was treated with different concentration of calcium carbide whereas control group was not treated. The peel and pulp samples were oven dried and ground to fine powder separately. The elemental compositions were determined using Particle Induced X-ray emission and Pelletron Tandem Accelerator. Result: Sixteen elements were identified in peach fruits and the elements were Al, P, S, Cl, K, Ca, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, and Se. In peel, concentration of some elements increased or decreased after treatment with CaC2 while in pulp the conc. of nearly all detected elements was increased in treated samples. We found significantly high amount of heavy metals traces including As, Se, Co, Si, and P in peach fruits treated with CaC2. Interestingly, the presence of trichomes in peach skin prevents the transfer of these heavy metals deep into the pulp which was also verified by the elemental profiling of nectarines. Conclusion: Conclusively, the artificial ripening with CaC2 changed the nutritional value of peach fruits that has higher health risks if consume with the peel. According to our best knowledge, this is the first report that highlights the effects of CaC2 which deteriorate the nutritional value of peach fruits in Pakistan.

Sign in / Sign up

Export Citation Format

Share Document