scholarly journals Nonisothermal Kinetic Degradation of Hybrid CNT/Alumina Epoxy Nanocomposites

Metals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 657
Author(s):  
Muhammad Helmi Abdul Kudus ◽  
Muhammad Razlan Zakaria ◽  
Mohd Firdaus Omar ◽  
Muhammad Bisyrul Hafi Othman ◽  
Hazizan Md. Akil ◽  
...  
Keyword(s):  
Activation Energy ◽  
Thermal Degradation ◽  
Degradation Kinetics ◽  
Filler Loading ◽  
Nitrogen Atmosphere ◽  
Lifetime Prediction ◽  
Thermal Degradation Kinetics ◽  
Epoxy Nanocomposites ◽  
Hybrid Filler ◽  
Degradation Activation Energy

Due to the synergistic effect that occurs between CNTs and alumina, CNT/alumina hybrid-filled epoxy nanocomposites show significant enhancements in tensile properties, flexural properties, and thermal conductivity. This study is an extension of previously reported investigations into CNT/alumina epoxy nanocomposites. A series of epoxy composites with different CNT/alumina loadings were investigated with regard to their thermal-degradation kinetics and lifetime prediction. The thermal-degradation parameters were acquired via thermogravimetric analysis (TGA) in a nitrogen atmosphere. The degradation activation energy was determined using the Flynn–Wall–Ozawa (F-W-O) method for the chosen apparent activation energy. The Ea showed significant differences at α > 0.6, which indicate the role played by the CNT/alumina hybrid filler loading in the degradation behavior. From the calculations, the lifetime prediction at 5% mass loss decreased with an increase in the temperature service of nitrogen. The increase in the CNT/alumina hybrid loading revealed its contribution towards thermal degradation and stability. On average, a higher Ea was attributed to greater loadings of the CNT/alumina hybrid in the composites.

Thermal degradation kinetics of oxo-degradable PP/PLA blends

2018 ◽  
Vol 39 (1) ◽  
pp. 58-67 ◽  
Author(s):  
Dev K. Mandal ◽  
Haripada Bhunia ◽  
Pramod K. Bajpai
Keyword(s):  
Activation Energy ◽  
Thermal Stability ◽  
Thermogravimetric Analysis ◽  
Thermal Degradation ◽  
Kinetic Parameters ◽  
Degradation Kinetics ◽  
Nitrogen Atmosphere ◽  
Thermal Degradation Kinetics ◽  
Heating Rates ◽  
Kinetics Of

AbstractIn this article, the influence of polylactide and pro-oxidant on the thermal stability, degradation kinetics, and lifetime of polypropylene has been investigated using thermogravimetric analysis under nitrogen atmosphere at four different heating rates (i.e. 5, 10, 15, and 20°C/min). The kinetic parameters of degradation were studied over a temperature range of 30–550°C. The derivative thermogravimetric curves have indicated single stage and two stage degradation processes. The activation energy was evaluated by using the Kissinger, Kim-Park, and Flynn-Wall methods under the nitrogen atmosphere. The activation energy value of polypropylene was much higher than that of polylactide. Addition of polylactide and pro-oxidant in polypropylene decreased the activation energy. The lifetime of polypropylene has also decreased with the addition of polylactide and pro-oxidant.

Non-isothermal degradation kinetics for polycarbonate/ polymethylphenylsilsesquioxane composites

e-Polymers ◽  
2010 ◽  
Vol 10 (1) ◽  
Author(s):  
Jiangbo Wang ◽  
Zhong Xin
Keyword(s):  
Activation Energy ◽  
Thermogravimetric Analysis ◽  
Thermal Degradation ◽  
Flame Retardancy ◽  
Degradation Kinetics ◽  
Degradation Process ◽  
Nitrogen Atmosphere ◽  
Ozawa Method ◽  
Degradation Behaviors ◽  
Thermal Degradation Process

AbstractThe thermal degradation behaviors of PC/PMPSQ (polymethylphenylsilsesquioxane) systems were investigated by thermogravimetric analysis (TGA) under non-isothermal conditions in nitrogen atmosphere. During non-isothermal degradation, Kissinger and Flynn-Wall-Ozawa methods were used to analyze the thermal degradation process. The results showed that a remarkable decrease in activation energy ( E ) was observed in the early and middle stages of thermal degradation in the presence of PMPSQ, which indicated that the addition of PMPSQ promoted the thermal degradation of PC. Flynn-Wall-Ozawa method further revealed that PMPSQ significantly increased the activation energy of PC thermal degradation in the final stage, which illustrated that the PMPSQ stabilized the char residues and improved the flame retardancy of PC in the final period of thermal degradation process

Non-isothermal crystallization and thermal degradation kinetics of MXene/linear low-density polyethylene nanocomposites

e-Polymers ◽  
2017 ◽  
Vol 17 (5) ◽  
pp. 373-381 ◽  
Author(s):  
Xinxin Cao ◽  
Mengqi Wu ◽  
Aiguo Zhou ◽  
You Wang ◽  
Xiaofang He ◽  
...  
Keyword(s):  
Activation Energy ◽  
Thermal Stability ◽  
Thermal Degradation ◽  
Isothermal Crystallization ◽  
Degradation Kinetics ◽  
Thermal Degradation Kinetics ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Linear Low Density Polyethylene ◽  
Kinetics Of

AbstractA novel two-dimensional material MXene was used to synthesize nanocomposites with linear low-density polyethylene (LLDPE). The influence of MXene on crystallization and thermal degradation kinetics of LLDPE was investigated. Non-isothermal crystallization kinetics was investigated by using differential scanning calorimetry (DSC). The experimental data was analyzed by Jeziorny theory and the Mo method. It is found that MXene acted as a nucleating agent during the non-isothermal crystallization process, and 2 wt% MXene incorporated in the nanocomposites could accelerate the crystallization rate. Findings from activation energy calculation for non-isothermal crystallization came to the same conclusion. Thermal gravity (TG) analysis of MXene/LLDPE nanocomposites was conducted at different heating rates, and the TG thermograms suggested the nanocomposites showed an improvement in thermal stability. Apparent activation energy (Ea) of thermal degradation was calculated by the Kissinger method, and Ea values of nanocomposites were higher than that of pure LLDPE. The existence of MXene seems to lead to better thermal stability in composites.

Effect of Pd Nanoparticle on the Thermal Degradation Kinetics of Nylon 6/Pd Nanocomposite Prepared by a Dry Process

2012 ◽  
Vol 486 ◽  
pp. 27-33 ◽  
Author(s):  
Jae Young Lee ◽  
Sung Wan Hong ◽  
Kyeong Sik Han ◽  
Taeck Hong Lee ◽  
Hong Ki Lee
Keyword(s):  
Activation Energy ◽  
Thermal Degradation ◽  
Degradation Kinetics ◽  
Pd Nanoparticles ◽  
Nylon 6 ◽  
Thermal Degradation Kinetics ◽  
Heating Rates ◽  
Dry Process ◽  
Effect Of Pd ◽  
Kinetics Of

Palladium (Pd) nanoparticles were incorporated into a nylon 6 film via a dry process which consisted of simultaneous vaporization, penetration and reduction processes of palladium (II) bis (acetylacetonate, Pd (acac)2) at 180°C for various exposure time. The even dispersion of the generated Pd nanoparticles were observed by transmission electron microscope (TEM) and the Pd loading weight of about 15~43 wt% was measured by thermogravimetric analysis (TGA). In order to study the catalytic effect of Pd nanoparticles on the thermal degradation kinetics of nylon 6, TGA data at various heating rates were introduced to Flynn & Wall equation. The thermal degradation activation energy for neat nylon 6 was ca. 162~178 kJ/mol over the thermal degradation fraction of 0.05~0.40 while that of the nylon 6/Pd (26.5 wt%) nanocomposite was ca. 110~169 kJ/mol over the same fraction range. It meant the Pd nanoparticles were acted as a catalyst on the depolymerization of amide group in nylon 6. It was also found that the activation energy decreased slightly with the increasing Pd loading weight.

scholarly journals Thermomechanical and Morphological Studies of CFRP Tested in Different Environmental Conditions

Materials ◽  
2018 ◽  
Vol 12 (1) ◽  
pp. 63 ◽  
Author(s):  
Claudia Barile ◽  
Caterina Casavola ◽  
Paramsamy Vimalathithan ◽  
Marco Pugliese ◽  
Vincenzo Maiorano
Keyword(s):  
Activation Energy ◽  
Thermal Degradation ◽  
Mass Loss ◽  
Environmental Conditions ◽  
Degradation Kinetics ◽  
Fiber Reinforced Polymers ◽  
Thermal Degradation Kinetics ◽  
Morphological Studies ◽  
Significant Difference ◽  
Kinetics Of

The present work describes the mechanical characterization combined with the thermal degradation kinetics of Carbon Fiber Reinforced Polymers (CFRP). The thermal degradation kinetics of CFRP have never been studied in the past. In that regard, the present work focuses on studying the thermal degradation kinetics of CFRP tested mechanically at different environmental conditions. Tensile tests were performed on the specimens with different lay-ups at room temperature, elevated temperature (71 °C), and cryogenic conditions (−54 °C), and the same specimens were used for thermal degradation kinetic studies. Mechanical tests show different responses respect to the different environmental conditions and different fibers orientation. On the other hand, the thermogravimetric results, mass loss, and derivative mass loss, show no significant difference in the degradation of CFRP tested at different temperatures. However, the thermal degradation kinetics shows more insight into the degradation pattern of the materials. The activation energy of degradation shows that the degradation of materials subjected to elevated conditions increases rapidly in the later stages of degradation, suggesting the formation of high char yield. The varying activation energy has been related to different degradation mechanisms. Lastly, the morphology of the materials was studied under SEM to understand the structural change in the material after tested in different weather conditions.

Thermal Degradation Kinetics of Poly (vinyl chloride)

2010 ◽  
Vol 96 ◽  
pp. 245-249 ◽  
Author(s):  
Bin Han ◽  
Yu Long Wu ◽  
Guo Rui ◽  
Wei Feng ◽  
Zhen Chen ◽  
...  
Keyword(s):  
Activation Energy ◽  
Thermal Degradation ◽  
Degradation Kinetics ◽  
Mass Conservation ◽  
Thermal Degradation Kinetics ◽  
Pyrolysis Mechanism ◽  
Second Stage ◽  
Volatile Products ◽  
Infrared Spectrometer ◽  
Kinetics Of

The thermal degradation of PVC resin was examined by the thermogravimetric analysis (TGA). The pyrolysis volatile products were analyzed by Fourier transform infrared spectrometer synchronized with TG test (TG-FTIR). Based on the TG results, the kinetics of thermal degradation was studied by Friedman method. The pyrolysis mechanism was discussed also. The results indicate that the pyrolysis process of PVC can be divided into two main stages: 220°C - 380°C and 380°C - 560°C. By the calculation of mass conservation and TG-FTIR results, it can be supposed that not only HCl, but also some unsubstituted aromatics such as benzene were released during the first stage. The comparison of activation energy shows that the second stage exhibited higher activation energy than the first stage. Two activation energy values in the first stage confirm that there arose two reactions in the first stage.

Thermal degradation kinetics and lifetime of HDPE/PLLA/pro-oxidant blends

2016 ◽  
Vol 36 (9) ◽  
pp. 917-931 ◽  
Author(s):  
Gaurav Madhu ◽  
Dev K. Mandal ◽  
Haripada Bhunia ◽  
Pramod K. Bajpai
Keyword(s):  
Activation Energy ◽  
Thermal Degradation ◽  
Degradation Kinetics ◽  
Model Fitting ◽  
Frequency Factor ◽  
Thermal Degradation Kinetics ◽  
Heating Rates ◽  
Model Free ◽  
Calculation Technique ◽  
Thermal Degradation Behavior

Abstract The effect of adding poly(L-lactic acid) (PLLA) with and without a pro-oxidant additive cobalt stearate (CoSt) and compatibilizer maleic anhydride grafted polyethylene (MA-g-PE) on the thermal degradation and stability of high-density polyethylene (HDPE) films was analyzed using thermogravimetric analysis (TGA). The kinetic parameters [i.e. activation energy (Ea), order of reaction (n), and frequency factor ln(A)] of the samples were studied over a temperature range of 25°C–600°C at four heating rates (i.e. 5, 10, 15, and 20°C/min) through model-free techniques (e.g. Friedman, second Kissinger, and Flynn-Wall-Ozawa) and model-fitting techniques (e.g. Freeman-Carroll and Kim-Park). The value of Ea for neat HDPE was found to be much higher than PLLA; for the HDPE/PLLA blend, it was nearer to that of HDPE. An increase in the activation energy of 80/20 (HDPE/PLLA) blend was noticed by the addition of MA-g-PE. The TGA data and degradation kinetics were also used to predict the lifetime of the film samples. The lifetime of HDPE was found to decrease with the increase in the concentration of CoSt, thereby revealing its pro-oxidative ability. Minimum lifetime was noted for the HDPE/PLLA (80/20) sample blended with CoSt, which increased slightly in the presence of MA-g-PE. Studies indicated that the thermal degradation behavior and lifetime of the investigated film samples depends not only on the fractions of their constituents but also on the heating rates and calculation technique.

Sign in / Sign up

Export Citation Format

Share Document