scholarly journals New Metallic Damper with Multiphase Behavior for Seismic Protection of Structures

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 183
Author(s):  
Amadeo Benavent-Climent ◽  
David Escolano-Margarit ◽  
Julio Arcos-Espada ◽  
Hermes Ponce-Parra
Keyword(s):  
Energy Dissipation ◽  
Large Deformations ◽  
Cyclic Behavior ◽  
Displacement Curve ◽  
Hysteretic Model ◽  
Reinforced Concrete Structure ◽  
Shake Table Tests ◽  
Energy Dissipation Capacity ◽  
Multiphase Behavior ◽  
Metallic Damper

This paper proposes a new metallic damper based on the plastic deformation of mild steel. It is intended to function as an energy dissipation device in structures subjected to severe or extreme earthquakes. The damper possesses a gap mechanism that prevents high-cycle fatigue damage under wind loads. Furthermore, subjected to large deformations, the damper presents a reserve of strength and energy dissipation capacity that can be mobilized in the event of extreme ground motions. An extensive experimental investigation was conducted, including static cyclic tests of the damper isolated from the structure, and dynamic shake-table tests of the dampers installed in a reinforced concrete structure. Four phases are distinguished in the response. Based on the results of the tests, a hysteretic model for predicting the force-displacement curve of the damper under arbitrary cyclic loadings is presented. The model accurately captures the increment of stiffness and strength under very large deformations. The ultimate energy dissipation capacity of the damper is found to differ depending on the phase in which it fails, and new equations are proposed for its prediction. It is concluded that the damper has a stable hysteretic response, and that the cyclic behavior, the ultimate energy dissipation capacity and failure are highly predictable with a relatively simple numerical model.

scholarly journals The Effects of Plaster Thicknesses on Cyclic Behavior of Infill Walls with Different Materials

2020 ◽  
Author(s):  
Mehmet Emin Arslan ◽  
Elif Ağcakoca ◽  
Merve Şentürk
Keyword(s):  
Energy Dissipation ◽  
Cyclic Behavior ◽  
Dissipated Energy ◽  
Cyclic Loads ◽  
Reinforced Concrete Structure ◽  
Backbone Curve ◽  
Infill Walls ◽  
Load Carrying ◽  
Materials Used ◽  
Set Up

Reinforced concrete structure systems are usually designed as frame or shear wall-frame systems. It is possible to reduce the deformation and displacement in the system by increasing the structural stiffness. Besides, large displacements on the floors caused by horizontal load are damped by the cracks in these walls. The present paper aims to examine the effects of materials used in the wall construction as well as thickness of the plaster on the behavior of infill walls under cyclic loads. In order to investigate the above mentioned effects, three Infill walls that were produced from three different materials namely, horizontal hollow bricks, pumice blocks and aerated concrete blocks were tested in three setups (without plaster, with 1 cm plaster and 2.5 cm plaster on it). In order to determine pure wall contribution, the infill walls were placed in a steel frame test set-up which was hinged from all four corners and were then exposed to cyclic loads taking into account the displacement controlled loading protocol proposed in FEMA 461. Right after applying the plaster to the infill walls, load carrying and energy dissipation capacities of the walls were examined comparatively. Load-displacement, backbone curve and cumulative dissipated energy curves of each infill walls are generated using the data collected from the experiments and the infill walls behaviors are graphically explained. Test results showed that existence and thickness of plaster significantly affected cyclic behavior of the test walls by increasing energy dissipation capacities and load carrying capacities.

Experimental Test of Welded Wide Flange Fuses

2018 ◽  
Vol 763 ◽  
pp. 414-422 ◽  
Author(s):  
Tony Y. Yang ◽  
Winda Banjuradja ◽  
Lisa Tobber
Keyword(s):  
Energy Dissipation ◽  
Longitudinal Direction ◽  
Elastic Stiffness ◽  
Design Parameters ◽  
Structural Components ◽  
Earthquake Energy ◽  
Aspect Ratios ◽  
Metallic Dampers ◽  
Energy Dissipation Capacity ◽  
Metallic Damper

Metallic dampers are one of the most prevalent structural components that are used to dissipate earthquake energy. A novel metallic damper, named Welded Wide Flange Fuse (WWFF), is proposed in this paper. WWFF utilizes commonly available welded wide flange sections to dissipate the earthquake energy through shear yielding of the web in the longitudinal direction, which makes the WWFF easy to be fabricated and efficient in providing high elastic stiffness and stable energy dissipation capacity. In this paper, a detailed experimental study was conducted to examine the influence on the design parameters (such as aspect ratios and slenderness ratios) on the component response (such as yielding force and elastic stiffness). The result shows that the WWFF has stable energy dissipation capacity which can be used as an efficient and robust metallic damper.

scholarly journals Cyclic Responses of Two-Side-Connected Precast-Reinforced Concrete Infill Panels with Different Slit Types

Buildings ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 16
Author(s):  
Guohua Sun ◽  
Fei Li ◽  
Qiyou Zhou
Keyword(s):  
Reinforced Concrete ◽  
Energy Dissipation ◽  
Failure Mode ◽  
Damping Ratio ◽  
Concrete Strength ◽  
Plastic Hinge ◽  
Cyclic Behavior ◽  
Lateral Stiffness ◽  
Lateral Strength ◽  
Energy Dissipation Capacity

This study aimed to study the cyclic behavior of two-side-connected precast-reinforced concrete infill panel (RCIP). A total of four RCIP specimens with different slit types and height-to-span ratios modeled at a one-third scale were tested subjected to cyclic lateral loads. The failure mode, hysteretic behavior, lateral strength, stiffness degradation, ductility, and energy dissipation capacity of each RCIP specimen were determined and analyzed. The specimens experienced a similar damage process, which involved concrete cracking, steel rebar yielding, concrete crushing, and plastic hinge formation. All the specimens showed pinched hysteretic curves, resulting in a small energy dissipation capacity and a maximum equivalent viscous damping ratio lower than 0.2. The specimens with penetrated slits experienced ductile failure, in which flexural hinges developed at both slit wall ends. The application of penetrated slits decreased the initial stiffness and lateral load-bearing capacity of the RC panel but increased the deformation capacity, the average ultimate drift ratios ranged from 1.41% to 1.99%, and the lowest average ductility ratio reached 2.48. The specimens with high-strength concrete resulted in a small slip no more than 1 mm between the RC panel and steel beam, and the channel shear connectors ensured that the RC infill panel developed a reliable assembly with the surrounding steel components. However, specimens with concealed vertical slits (CVSs) and concealed hollow slits (CHSs) achieved significantly higher lateral stiffness and lateral strength values. Generally, the specimens exhibited two-stage mechanical features. The concrete in the CVSs and CHSs was crushed, and flexural plastic hinges developed at both ends of the slit walls during the second stage. With increasing concrete strength, the initial lateral stiffness and lateral strength values of the RCIP specimens increased. With an increasing height-to-span ratio, the lateral stiffness and strength of the RC panels with slits decreased, but the failure mode remained unchanged.

scholarly journals Seismic Evaluation of New Steel Infill Panels for Steel Shear Walls

2021 ◽  
Vol 7 (4) ◽  
pp. 633-648
Author(s):  
Ali Joharchi ◽  
Siti Aminah Osman ◽  
Mohd Yazmil Md Yatim ◽  
Mohammad Ansari
Keyword(s):  
Energy Dissipation ◽  
Ultimate Load ◽  
Shear Walls ◽  
Shear Wall ◽  
Cyclic Behavior ◽  
Lower Amount ◽  
Seismic Evaluation ◽  
Steel Plate Shear Wall ◽  
Infill Panels ◽  
Energy Dissipation Capacity

Corrugated Steel Shear Wall (CSSW) is an efficient shear wall system, which has higher energy dissipation capacity, ductility and stiffness when compared to the Steel Plate Shear Wall (SPSW) with flat infill plate. Despite of these advantages, the ultimate load of CSSW is lower than that of SPSW. Various studies conducted to improve the cyclic behavior of CSSW revealed that increasing corrugation angle might enhance energy dissipation capacity and toughness of CSSWs. However, the ultimate load of CSSW was not improved by increasing the corrugation angle. Thus, the current study proposed new corrugated infill panel schemes to improve the ultimate load of CSSWs. To this end, Finite Element (FE) models were established using ABAQUS/Standard and verified with the experimental results from previous researches. The corrugation angle of the proposed plates was found based on a numerical investigation on seven CSSW FE models with the corrugation angle ranges from 30° to 120°. The FE results revealed that the model with the corrugation angle of 120 achieved highest ultimate load, energy dissipation capacity and toughness amongst the CSSW models. In addition, the ultimate loads, energy dissipation capacities and toughness of the proposed infill plates were up to 11.8%, 53.9% and 8.8% respectively higher than those of CSSW model with the corrugation angle of 120°. Furthermore, the proposed infill plates use up to 13.4% lower amount of steel compared to the corrugated plate with the corrugation angle of 120. Doi: 10.28991/cej-2021-03091678 Full Text: PDF

scholarly journals Effects of the Replacement Length of Concrete with ECC on the Cyclic Behavior of Reinforced Concrete Columns

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3542
Author(s):  
Jung-Hwan Hyun ◽  
Jin-Wook Bang ◽  
Bang-Yeon Lee ◽  
Yun-Yong Kim
Keyword(s):  
Reinforced Concrete ◽  
Energy Dissipation ◽  
Cyclic Loading ◽  
Load Test ◽  
Cyclic Behavior ◽  
Cyclic Loading Condition ◽  
Composite Columns ◽  
Rc Column ◽  
Energy Dissipation Capacity ◽  
Cyclic Loading Tests

This paper presents an experimental investigation on the effects of the replacement length of concrete with engineered cementitious composites (ECC) on the cyclic behavior of a reinforced concrete (RC) column. A conventional RC column specimen and two RC composite columns designed with ECC were fabricated. To investigate the cyclic behavior of each specimen, a series of cyclic loading tests was performed under a reversed cyclic loading condition with a constant axial load. Test results showed that ECC columns exhibited higher cyclic behavior in terms of load carrying capacity, ductility, and energy dissipation capacity compared to the RC column. It was also found that when applying ECC to the column specimen with a length of 3.6d or more, the energy dissipation capacity was greatly increased.

scholarly journals Metallic Slit-Plate Dampers: Damage Evaluation with Metal Magnetic Memory Technique and Application to Structures with Rocking Columns

Metals ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 953 ◽  
Author(s):  
Chihab Abarkane ◽  
German Ríos-García ◽  
David Gale-Lamuela ◽  
Francisco Rescalvo ◽  
Antolino Gallego ◽  
...  
Keyword(s):  
Energy Dissipation ◽  
Damage Index ◽  
Magnetic Memory ◽  
Metallic Materials ◽  
Concrete Frames ◽  
Metallic Dampers ◽  
Energy Dissipation Capacity ◽  
Metallic Slit ◽  
Cost Efficient ◽  
Metallic Damper

Inelastic deformation of metallic materials is one of the most effective mechanisms for the dissipation of energy input to a structure by an earthquake. Metallic dampers are special devices that resort to this source of energy dissipation, proving to be a cost-efficient solution for the seismic protection of structures. Two important issues arise when implementing metallic dampers in real structures: (1) Inelastic deformations cause damage that must be quantified after an earthquake to decide upon their eventual replacement; (2) dampers must possess an energy dissipation capacity large enough to endure severe earthquakes. This paper focuses on a particular type of metallic damper consisting of slit-plates made of stainless steel, applied to reinforced concrete frames with rocking columns at the first story. In particular, a new damage index based on the metallic magnetic memory (MMM) method is proposed and validated experimentally to quantify the damage of slit plate dampers subjected to cyclic loadings. Further, the seismic response of a frame with rocking columns that incorporate the damper is obtained to demonstrate that it can endure severe earthquakes without failing, and to emphasize the relevance of the proposed MMM damage index that would make its replacement after a severe earthquake unnecessary.

scholarly journals The Experimental Analysis Of An Innovative Yielding Metallic Damper

2015 ◽  
Vol 11 (2) ◽  
pp. 38-45 ◽  
Author(s):  
Vasile-Mircea Venghiac ◽  
Mihai Budescu
Keyword(s):  
Experimental Study ◽  
Energy Dissipation ◽  
Seismic Energy ◽  
Seismic Protection ◽  
Frame Structures ◽  
Shake Table ◽  
Natural Phenomena ◽  
Steel Frame Structures ◽  
Energy Dissipation Capacity ◽  
Metallic Damper

Abstract One of the most destructive natural phenomena is the earthquake. These events destroy lives, goods and disrupt human activities. For this reason the anti-seismic protection of buildings is a very important and of interest subject in Civil Engineering. In the case of structures with a low seismic energy dissipation capacity (for example steel frame structures with Slimdek composite floors), this problem becomes more complicated due to the requirement of dampers. In this paper an experimental study is presented regarding an innovative yielding metallic energy dissipation device, proposed by the author. An experiment is carried out on a shake table. By studying the results from the experiments and from the previous carried out numerical analysis we can conclude that this device provides a high anti-seismic protection for this type of structures.

scholarly journals Experimental and Numerical Analysis of the Mechanical Properties of a Pretreated Shape Memory Alloy Wire in a Self-Centering Steel Brace

Processes ◽  
2021 ◽  
Vol 9 (1) ◽  
pp. 80
Author(s):  
Bo Zhang ◽  
Sizhi Zeng ◽  
Fenghua Tang ◽  
Shujun Hu ◽  
Qiang Zhou ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Energy Dissipation ◽  
Shape Memory Alloy ◽  
Shape Memory ◽  
Loading Rate ◽  
Effective Elastic Modulus ◽  
Maximum Energy ◽  
Numerical Results ◽  
Energy Dissipation Capacity

As a stimulus-sensitive material, the difference in composition, fabrication process, and influencing factors will have a great effect on the mechanical properties of a superelastic Ni-Ti shape memory alloy (SMA) wire, so the seismic performance of the self-centering steel brace with SMA wires may not be accurately obtained. In this paper, the cyclic tensile tests of a kind of SMA wire with a 1 mm diameter and special element composition were tested under multi-working conditions, which were pretreated by first tensioning to the 0.06 strain amplitude for 40 cycles, so the mechanical properties of the pretreated SMA wires can be simulated in detail. The accuracy of the numerical results with the improved model of Graesser’s theory was verified by a comparison to the experimental results. The experimental results show that the number of cycles has no significant effect on the mechanical properties of SMA wires after a certain number of cyclic tensile training. With the loading rate increasing, the pinch effect of the hysteresis curves will be enlarged, while the effective elastic modulus and slope of the transformation stresses in the process of loading and unloading are also increased, and the maximum energy dissipation capacity of the SMA wires appears at a loading rate of 0.675 mm/s. Moreover, with the initial strain increasing, the slope of the transformation stresses in the process of loading is increased, while the effective elastic modulus and slope of the transformation stresses in the process of unloading are decreased, and the maximum energy dissipation capacity appears at the initial strain of 0.0075. In addition, a good agreement between the test and numerical results is obtained by comparing with the hysteresis curves and energy dissipation values, so the numerical model is useful to predict the stress–strain relations at different stages. The test and numerical results will also provide a basis for the design of corresponding self-centering steel dampers.

scholarly journals Experimental/Numerical Evaluation of Steel Trapezoidal Corrugated Infill Panels with an Opening

2021 ◽  
Vol 11 (7) ◽  
pp. 3275
Author(s):  
Majid Yaseri Gilvaee ◽  
Massood Mofid
Keyword(s):  
Energy Dissipation ◽  
Ultimate Strength ◽  
Steel Plate ◽  
Shear Walls ◽  
Experimental Results ◽  
Structural Performance ◽  
Initial Stiffness ◽  
Infill Panels ◽  
Energy Dissipation Capacity ◽  
Ductility Ratio

This paper investigates the influence of an opening in the infill steel plate on the behavior of steel trapezoidal corrugated infill panels. Two specimens of steel trapezoidal corrugated shear walls were constructed and tested under cyclic loading. One specimen had a single rectangular opening, while the other one had two rectangular openings. In addition, the percentage of opening in both specimens was 18%. The initial stiffness, ultimate strength, ductility ratio and energy dissipation capacity of the two tested specimens are compared to a specimen without opening. The experimental results indicate that the existence of an opening has the greatest effect on the initial stiffness of the corrugated steel infill panels. In addition, the experimental results reveal that the structural performance of the specimen with two openings is improved in some areas compared to the specimen with one opening. To that end, the energy dissipation capacity of the specimen with two openings is obtained larger than the specimen with one opening. Furthermore, a number of numerical analyses were performed. The numerical results show that with increasing the thickness of the infill plate or using stiffeners around the opening, the ultimate strength of a corrugated steel infill panel with an opening can be equal to or even more than the ultimate strength of that panel without an opening.

Sign in / Sign up

Export Citation Format

Share Document