scholarly journals Effect of Heat Treatment on Microstructure and Mechanical Properties of New Cold-Rolled Automotive Steels

Metals ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1414
Author(s):  
Fei Huang ◽  
Jian Chen ◽  
Zhangqi Ge ◽  
Junliang Li ◽  
Yongqiang Wang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Testing Machine ◽  
Second Phase ◽  
Isothermal Heat Treatment ◽  
Austenitizing Temperature ◽  
Austenite Grain Size ◽  
Austenite Grain ◽  
Microstructure And Mechanical Properties ◽  
Cold Rolled

The effect of austenitizing temperature and aging treatment on the microstructure and mechanical properties of two new cold-rolled automotive steel plates (20Mn2Cr and 20Mn2CrNb) was investigated by using isothermal heat treatment, optical microscope, scanning electron microscope, microhardness tester, and tensile testing machine. The results show that as the austenitizing temperature increased, the original austenite grain sizes of both steels increased. The original austenite grain size of 20Mn2CrNb was smaller than that of 20Mn2Cr. The microhardness of 20Mn2CrNb gradually decreased with increasing aging temperature, while the hardness of 20Mn2Cr varied irregularly. The mechanical properties of 20Mn2Cr were better than those of 20Mn2CrNb under the same heat-treatment process. The effect of heat treatment on microstructure and mechanical properties was related to the martensite content, dislocation density, and precipitation of second-phase particles.

Effect of Nd Content and Heat Treatment on Microstructure and Mechanical Properties of Mg-Zn-Nd Alloy

2017 ◽  
Vol 898 ◽  
pp. 124-130 ◽  
Author(s):  
Shu Min Xu ◽  
Xin Ying Teng ◽  
Xing Jing Ge ◽  
Jin Yang Zhang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Cast Alloy ◽  
Second Phase ◽  
Casting Method ◽  
Magnesium Matrix ◽  
Microstructure And Mechanical Properties

In this paper, the microstructure and mechanical properties of the as-cast and heat treatment of Mg-Zn-Nd alloy was investigated. The alloy was manufactured by a conventional casting method, and then subjected to a heat treatment. The results showed that the microstructure of as-cast alloy was comprised of α-Mg matrix and Mg12Nd phase. With increase of Nd content, the grain size gradually decreased from 25.38 μm to 9.82 μm. The ultimate tensile strength and elongation at room temperature of the Mg94Zn2Nd4 alloy can be reached to 219.63 MPa and 5.31%. After heat treatment, part of the second phase dissolved into the magnesium matrix and the grain size became a little larger than that of the as-cast. The ultimate tensile strength was declined by about 2.5%, and the elongation was increased to 5.47%.

The Effect of Heat Treatment on Microstructure and Mechanical Properties of ZK60 Alloy

2007 ◽  
Vol 353-358 ◽  
pp. 718-721
Author(s):  
Ding Fei Zhang ◽  
Rong Shen Liu ◽  
Jian Peng ◽  
Wei Yuang ◽  
Hong Ju Zhang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solid Solution ◽  
Age Hardening ◽  
Second Phase ◽  
Solid Solution Strengthening ◽  
Microstructure And Mechanical Properties ◽  
Long Time ◽  
Zk60 Alloy ◽  
Solution Strengthening

With different heat treatment, the microstructure and mechanical properties of ZK60 magnesium alloy were investigated. It can be concluded that heat treatment has great effect on mechanical properties of ZK60. With artificial aging after extruding, the precipitation of the second phase from the supersaturated solid solution significantly improved mechanical properties. It can greatly increase yield strength of ZK60 alloy, while the tensile strength has little change. For the combination of solid solution strengthening and age hardening, two opposite factors must be considered. On one hand, the solid solution strengthening and the later precipitation strengthening is good for alloy’s strength; on the other hand, the properties decrease as the grains grew under high temperature for a long time during solution heating.

Microstructure and Mechanical Properties of Mg-9Gd-4Y-0.5Zr Alloy

2017 ◽  
Vol 904 ◽  
pp. 15-18
Author(s):  
Bo Bo Meng ◽  
Quan An Li ◽  
Xiao Ya Chen
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solid Solution ◽  
Tensile Testing ◽  
Treatment Process ◽  
Testing Machine ◽  
Elongation Rate ◽  
Heat Treatment Process ◽  
Tensile Testing Machine ◽  
Microstructure And Mechanical Properties

The effects of heat treatment on microstructure and mechanical properties of Mg-9Gd-4Y-0.5Zr alloy were studied by XRD, OM, SEM and tensile testing machine. The results show that the alloy mainly consists of α-Mg matrix, Mg5Gd and Mg24Y5. Through solid solution and aging heat treatment process, the tensile strength, yield strength and elongation rate respectively achieves 263.1MPa, 235.2MPa and 3.11%.

Electron Microscope studies of the microstructures in as-quenched and aged HSLA-100 production steels and correlation with mechanical properties

1991 ◽  
Vol 49 ◽  
pp. 582-583
Author(s):  
A.G. Fox ◽  
V.R. Mattes ◽  
S. Mikalac ◽  
M.G. Vassilaros
Keyword(s):  
Mechanical Properties ◽  
High Strength ◽  
Low Carbon ◽  
Austenite Grain Size ◽  
Solid Solution Strengthening ◽  
Austenite Grain ◽  
Microstructure And Mechanical Properties ◽  
Hsla Steels ◽  
Carbonitride Precipitation ◽  
Strength And Toughness

Because of their excellent weldability, high strength low alloy (HSLA) ultra low carbon bainitic (ULCB) steels are finding increasing applications in ship and submarine construction. In order to achieve the required strength and toughness in ULCB HSLA steels it is necessary to control chemical composition and thermo-mechanical processing very carefully so that the desired microstructure and mechanical properties can be achieved. For instance HSLA 100 ULCB steel (nominal yield strength 100 ksi) used by the U.S. Navy in shipbuilding applications can derive its strength and toughness from the following sources:- (1) solid solution strengthening (2) small prior austenite grain size derived from niobium carbonitride precipitation at austenite grain boundaries (3) dislocation substructure and (4) from copper precipitates (in aged alloys). The object of the present work is to correlate the microstructure and mechanical properties of production batches of HSLA 100 in the quenched and aged conditions. Because many of the salient features of these microstructures are submicron in size it was found necessary to use SEM and TEM.

The effect of heat treatment on the mechanical properties of a low carbon steel (0.1%) for offshore structural application

2012 ◽  
Vol 226 (3) ◽  
pp. 242-251 ◽  
Author(s):  
Sung S Kang ◽  
Amir Bolouri ◽  
Chung-Gil Kang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Cooling Rate ◽  
Impact Energy ◽  
Cast Steel ◽  
Low Carbon ◽  
Austenite Grain Size ◽  
Tempering Temperature ◽  
Austenite Grain

In this study, a low carbon cast steel (0.1% C) alloy designed for offshore structures, and the mechanical properties of the alloy under different heat treatment cycles have been evaluated. The effect of austenitizing time on the austenite grain size was studied. Subsequently, the quenched samples with minimum austenite grain size subjected to tempering experiments at different tempering temperatures (450 °C, 550 °C, and 650 °C) and cooling rates (0.23, 36, and 50 °C/s) from the temperature. The results showed that by increasing the austenitizing time, the austenite grain size initially decreased and reached the minimum value with ASTM number of 6.35 and then followed by an increase. When the tempering temperature increased, yield and tensile strengths decreased, whereas the ductility properties improved. In addition, yield and tensile strengths were not affected by cooling rate from tempering temperature, whereas the ductility properties were slightly affected. The increase in tempering temperature significantly led to improvement in the toughness to fracture of the alloy. The effect of cooling rate on impact energy for the samples tempered at 450 °C and 550 °C was negligible. By the contrast, impact energy for the samples tempered at 650 °C was markedly affected by cooling rate, in which the highest value was achieved for a cooling rate of 50 °C/s.

Sign in / Sign up

Export Citation Format

Share Document