scholarly journals Effect of Deformation on Precipitation and the Microstructure Evolution during Multistep Thermomechanical Processing of Al-Zn-Mg-Cu Alloy

Metals ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1409
Author(s):  
Jinrong Zuo ◽  
Longgang Hou ◽  
Xuedao Shu ◽  
Wenfei Peng ◽  
Anmin Yin ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Electron Microscope ◽  
Grain Boundaries ◽  
Grain Refinement ◽  
Hot Rolling ◽  
Hot Deformation ◽  
Rolling Process ◽  
Intermediate Annealing ◽  
Short Period

In order to obtain fine grained structure efficiently, a new multi-step rolling process (MSR: pre-deformation + intermediate annealing + hot deformation) was applied in Al-Zn-Mg-Cu plates. Conventional hot rolling (CHR) was also carried out as a contrast experiment. The evolution of microstructures and improvement of mechanical properties were analyzed by optical microscope, scanning electron microscope, transmission electron microscope, X-ray diffractometer, and tensile tests. The results show that the MSR process can obtain finer longitudinal grain size and better mechanical properties than CHR, which can be explained as follows: spheroidization of precipitates wrapped by high density dislocations could be promoted by increased pre-deformation; numerous ordered substructures were formed during short-period intermediate annealing at high temperature; in the subsequent hot rolling process, the retained spherical precipitates pinned dislocations and boundaries. With the increase of accumulated strain, low angle grain boundaries gradually transformed into high angle grain boundaries, leading to grain refinement. With the increased pre-deformation (MSR1 20 + 60%, MSR2 40 + 40%, MSR3 60 + 20%), the effect of grain refinement and plasticity improvement gradually weakened. The optimum thermomechanical process (MSR1 solid solution + pre-deformation (300 °C/20%) + intermediate annealing (430 °C/5 min) + hot deformation (400 °C/60%)) was obtained, which can increase elongation by ~25% compared with the CHR process, while maintaining similar high strength for reduced longitudinal grain size.

scholarly journals Grain Structure Evolution and Mechanical Properties of Multi-Channel Spiral Twist Extruded AA5083

Metals ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1276
Author(s):  
Dina M. Fouad ◽  
Waleed H. El-Garaihy ◽  
Mohamed M. Z. Ahmed ◽  
Ibrahim Albaijan ◽  
Mohamed M. El-Sayed Seleman ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Grain Boundaries ◽  
Tensile Properties ◽  
Grain Refinement ◽  
Electron Backscatter Diffraction ◽  
Comprehensive Evaluation ◽  
Structural Evolution ◽  
Grain Structure ◽  
Structure Evolution

This study presents a comprehensive evaluation of the effects of multi-channel spiral twist extrusion (MCSTE) processing on the mechanical properties and structural evolution of AA5083. The structural evolution and texture developed were mapped by electron backscatter diffraction (EBSD) for three successive passes and compared with an as-annealed plate. An evaluation of the hardness and tensile properties was presented and correlated with the EBSD findings. The displayed EBSD results revealed that grain refinement was strongly associated with the presence of a high density of low-angle grain boundaries (LAGBs) after one pass, which developed into fine grains of less than 20 μm and high-angle grain boundaries (HAGBs) after three MCSTE passes. The three pass processing led to a 65% reduction in grain size. This reduction in grain size was coupled with an enhancement in the hardness and tensile properties. Additionally, the crystallographic texture study represented a slightly random texture due to the presence of intermetallic particles in AA5083. This study demonstrates the efficacy of MCSTE as a grain refinement tool.

Mathematical Modelling of Hot Rolling: A Practical Tool to Improve Rolling Schedules and Steel Properties

2013 ◽  
Vol 762 ◽  
pp. 210-217 ◽  
Author(s):  
Fulvio Siciliano
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Hot Rolling ◽  
Hot Deformation ◽  
Low Cost ◽  
Cold Deformation ◽  
Development Stage ◽  
Hot Strip Mill ◽  
Mean Flow ◽  
Thin Slab Casting

Most of the commercial metallic materials undergo at least one hot deformation stage during fabrication. Hot deformation processing leads to the production of plates, strips, rods, pipes and other shapes at lower overall cost when compared to the cold deformation/annealing route. Comprehensive study of the metallurgical phenomena during hot deformation has enormous potential application in the control of industrial rolling processes. Understanding of the microstructural and mean flow stress evolution lead to sound steel developments and innovative rolling schedules. The models predict parameters such as grain size, fractional softening (static and dynamic) and strain induced precipitation which are useful to improve rolling schedules. Effects such as incomplete softening and strain accumulation can be easily detected as well as their consequences on the final grain size and mechanical properties. In this regard, special attention must be given to steels, the most important metallic material in terms of history, present and future. In this paper, three hot rolling routes will be analyzed in order to produce high strength linepipe steels. Examples were selected on how the use of modelling during development stage can help to meet mechanical properties, mainly toughness and drop weight tear test. Firstly, it is presented a brief overview on mathematical models applied to hot rolling. Thin slab casting/direct rolling, hot strip mill and plate mill are exemplified in the present work. The development of new steel grades can greatly accelerated with the aid of modelling, which is an useful, low-cost technique.

scholarly journals Primary Recrystallization Behaviors of Hi-B Steel with Lower Initial Nitrogen Produced by the Thin Slab Casting and Rolling Process

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 189
Author(s):  
Bing Fu ◽  
Li Xiang ◽  
Jia-Long Qiao ◽  
Hai-Jun Wang ◽  
Jing Liu ◽  
...  
Keyword(s):  
Grain Size ◽  
Electron Microscope ◽  
Nitrogen Content ◽  
Rolling Process ◽  
Primary Recrystallization ◽  
Thin Slab ◽  
Nitriding Temperature ◽  
Thin Slab Casting ◽  
Slab Casting ◽  
Inhomogeneity Factor

Based on low-temperature high-permeability grain-oriented silicon steel designed with an initial nitrogen content of 0.0055% and produced by the thin slab casting and rolling process, the effect of total nitrogen content and nitriding temperature on primary recrystallization microstructure and texture were studied by optical microscope, scanning electron microscope, transmission electron microscope, and electron backscatter diffraction. The nitriding temperature affects the primary recrystallization behaviors significantly, while the total nitrogen content has a small effect. As the nitriding temperature is 750–850 °C, the average primary grain size and its inhomogeneity factor are about 26.58–26.67 μm and 0.568–0.572, respectively. Moreover, the texture factor is mostly between 0.15 and 0.40. Because of the relatively sufficient inhibition ability of inherent inhibitors in a decarburized sheet, the nitriding temperature (750–850 °C) affects the primary recrystallization microstructure and texture slightly. However, as the nitriding temperature rises to 900–950 °C, the average primary grain size and its inhomogeneity factor increase to 27.75–28.26 μm and 0.575–0.578, respectively. Furthermore, because of the great increase on the area fraction of {112} <110> grains, part of texture factor is increased sharply. Therefore, in order to obtain better primary grain size and homogeneity, better texture composition, and stability of the decarburized sheet, the optimal nitriding temperature is 750–850 °C.

Effect of Composite Master Alloy on Mechanical Properties and Electrochemical Corrosion of ZL101 Alloy

2013 ◽  
Vol 749 ◽  
pp. 407-413
Author(s):  
Hong Xu ◽  
Xin Zhang ◽  
Ji Ping Ren ◽  
Min Peng ◽  
Shi Yang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Grain Refinement ◽  
Master Alloy ◽  
Mass Fraction ◽  
Electrochemical Corrosion ◽  
Corrosion Performance ◽  
Obvious Effect ◽  
Mechanical Properties And Corrosion

The mechanical properties and corrosion performances of the ZL101 alloy modified by the composite master alloy were investigated. The results showed that the master alloy had not only obvious effect of grain refinement, but also a significant role in refining dendrite grain of ZL101 alloy. The grain size decreased dramatically from 150μm to 62μm when the addition of composite master alloy is up to 0.5%(mass fraction) and the temperature is 720 for 30 minutes,. Its tensile strength and elongation increased by 27% and 42% respectively. The grain refinement of ZL101 alloy decreased its corrosion performance. The morphology of Si changed into globular from needle modified by NaF, instead of AlTiB.

scholarly journals Grain Refinement of a Powder Nickel-Base Superalloy Using Hot Deformation and Slow-Cooling

Materials ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 1978 ◽  
Author(s):  
Xianqiang Fan ◽  
Zhipeng Guo ◽  
Xiaofeng Wang ◽  
Jie Yang ◽  
Jinwen Zou
Keyword(s):  
Grain Size ◽  
Grain Refinement ◽  
Hot Deformation ◽  
Nickel Base Superalloy ◽  
Polycrystalline Nickel ◽  
Slow Cooling ◽  
Homogeneous Microstructure ◽  
Average Grain Size ◽  
Nickel Base ◽  
Base Superalloy

A pre-hot-deformation process was applied for a polycrystalline nickel-base superalloy to active deformation twins and dislocations, and subsequent slow cooling treatment was used to achieve grain refinement and microstructure homogenization. The microstructural evolution of the alloy was investigated, and the corresponding underlying mechanism was discussed. It was found that twinning mainly occurred in large grains during pre-hot-deformation owing to the stress concentration surrounding the large grains. High density dislocations were found in large grains, and the dislocation density increased approaching the grain boundary. The average grain size was refined from 30 μm to 13 μm after slow cooling with a standard deviation of grain size decreasing from 10.8 to 2.8, indicating a homogeneous microstructure. The grain refinement and microstructure homogenization during cooling process could be achieved via (i) static recrystallization (SRX), (ii) interaction of twin tips and γ’ precipitates, and (iii) grain coarsening hindered by γ’ precipitates in grain boundaries.

Investigation of Mechanical Properties of Nanostructured Titanium Processed by Warm ECAP Followed Cold Rolling

2014 ◽  
Vol 875-877 ◽  
pp. 63-67 ◽  
Author(s):  
Dinh van Hai ◽  
Nguyen Trong Giang
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Cold Rolling ◽  
Room Temperature ◽  
Pure Titanium ◽  
Rolling Process ◽  
Coarse Grain ◽  
Nanostructured Titanium

In this work, ECAP technique was combined with cold rolling process in order to enhance mechanical properties and microstructure of pure Titanium. Coarse grain (CG) Titanium with original grain size of 150 μm had been pressed by ECAP at 425oC by 4, 8 and 12 passes, respectively. This process then was followed by rolling at room temperature with 35%, 55%, and 75% rolling strains. After two steps, mechanical properties such as strength, hardness and microstructure of processed Titanium have been measured. The result indicated significant effect of cold rolling on tensile strength, hardness and microstructure of ECAP-Titanium.

scholarly journals Novel grain refinement of AZ91E magnesium alloy and the effect on hot tearing during solidfication

2021 ◽  
Author(s):  
Abdallah Elsayed
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Magnesium Alloy ◽  
Grain Refinement ◽  
Magnesium Alloys ◽  
Hot Tearing ◽  
Grain Refining ◽  
Grain Refiner ◽  
Structural Applications ◽  
Hot Tearing Susceptibility

For the A1-5Ti-1B grain refiner, the addition of 0.1 wt.% provided a 68 % reduction in grain size as compared to the unrefined AZ91E alloy at a holding time of five minutes. Grain growth restriction by TiB₂ particles was the source of grain refinement. With the addition of A1-5Ti-1B, only a small reduction in hot tearing susceptibility ws observed because large TiA1₃ particles bonded poorly with the eutectic and blocked feeding channels.The addition of 1.0 wt.% A1-1Ti-3B provided a grain size reduction of 63% as compared to the unrefined AZ91E alloy at a holding time of five minutes. The grain refinement with A1-1Ti-3B addition was attributed to a combination of TiB₂ grain growth restriction and A1B₂ nucleating sites. A significant reduction in hot tearing susceptibility was observed with A1-1Ti-3B addition as a result of a higher cooling rate and shorter local soldification time as compared to the AZ91E alloy. The reduction in hot tearing susceptibility was attributed to the good interface between eutectic and TiB₂ particles. Both grain refiners demonstrated a good resistance to fading during the holding times investigated. In addition, the AZ91E + A1-5Ti-1B and AZ91E + A1-1Ti-3B castings showed much fewer dislocation networks as compared to the untreated AZ91E casting.The development of efficient A1-Ti-B refiners can also improve castability of magnesium alloys. In addition, the fade resistant A1-Ti-B grain refiners can reduce operating costs and maintain productivity on the foundry floor. Thus, magnesium alloy with A1-Ti-B treatment have the potential for more demanding structural applications in the automobile and aerospace industries. Vehicle weight in the aerospace and automotive industries directly impacts carbon emissions and fuel efficiency. An increase in the use of lightweight materials for structural applications will result in lighter vehicles. Low density materials, such as magnesium (1.74 g/cm³) are a potential alternative to aluminium (2.70 g/cm³), to reduce component weight in structural applications.However, current magnesium alloys still do not have adequate mechanical properties and castability to meet the performance specifications of the automotive and aerospace industries. Grain refinement can significantly improve mechanical properties and reduce hot tearing during permanent mould casting. Recently, Al-Ti-B based grain refiners have shown potential in grain refining magnesium-aluminum alloys such as AZ91E. This study investigates the grain refining efficiency and fading of A1-5Ti-1B and A1-1Ti-3B in AZ91E magnesium alloy and their subsequent effect on hot tearing.The grain refiners were added at 0.1, 0.2, 0.5 and 1.0 wt.% levels. For the grain refinement and fading experiments, the castings were prepared using graphite moulds with holding times of 5, 10 and 20 minutes. For the hot tearing experiments, castings were produced representing the optimal addition level of each grain refiner. The castings were prepared using a permanent mould with pouring and mould temperatures of 720 and 180 ºC, respectively. The castings were characterized using SEM, TEM, optical microscopy and thermal analysis.

Effect of the Mg3N2 Sub-Micron Particle on the Grain Refinement of AZ80 Alloy

2022 ◽  
Vol 327 ◽  
pp. 45-53
Author(s):  
Jiehua Li ◽  
Maria Pammer ◽  
Ernst Neunteufl ◽  
Peter Schumacher
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Grain Refinement ◽  
Liquid State ◽  
High Performance ◽  
Great Loss ◽  
Micron Particle ◽  
Deformation Ability ◽  
Semi Solid ◽  
Az80 Alloy

AZ80 alloy has been widely used to produce high performance Mg casting and wrought parts for high-end applications due to its high mechanical properties and deformation ability. However, at least two important issues still need to be solved in order to further improve its mechanical properties and deformation ability. Firstly, the grain size of α-Mg in AZ80 alloy is relatively large (more than 1000 µm) due to a lack of efficient grain refinement methodologies. Secondly, the size of the eutectic Mg17Al12 phase is also large and the distribution of the eutectic Mg17Al12 phase is continuous, which is very harmful for the mechanical properties, in particular to elongation. In this paper, these two important issues are investigated by adding Mg3N2 sub-micron particle into AZ80 alloy and thereby refining the α-Mg and the eutectic Mg17Al12 phase. Firstly, the Mg3N2 sub-micron particle was directly added into AZ80 alloy by using mechanically stirring in the semi-solid state, subsequently the melting temperature was increased above the liquidous temperature, and finally the melting was casted in the liquid state. It was found that the grain size of α-Mg can be refined from 883.8 µm to 169.9 µm. More importantly, the eutectic Mg17Al12 phase was also refined and the distribution became discontinuous. It should be noted that directly adding the Mg3N2 sub-micron particle into AZ80 alloy leads to a great loss of the Mg3N2 sub-micron particle due to the weak wetting behavior between the Mg3N2 sub-micron particle and Mg melt. The second methodology through mixing Mg3N2 sub-micron particles with AZ91 chips using a twin extruder was also used to prepare AZ91 master alloy with 3wt.% Mg3N2 sub-micron particle, which was subsequently added into AZ80 alloy in the liquid state. In this way, a significant grain refinement of α-Mg and a simultaneous refinement of the eutectic Mg17Al12 phase in AZ80 alloy was also achieved. The grain size of α-Mg can be refined from 883.8 µm to 325.9 µm. However, no significant grain refinement by using UST was observed. Instead, the grain size increases from 325.9 µm to 448.6 µm, indicating that the Mg3N2 sub-micron particle may lose its grain refinement potency due to possible aggregation and clustering. This paper provides an efficient and simple methodology for the grain refinement of α-Mg and the simultaneous refinement of the eutectic Mg17Al12 phase in AZ80 alloy.

Thermal Conductivity of Si₃N₄ Ceramics Fabricated From Carbothermal-reduction-derived Powder

2021 ◽  
Author(s):  
Yuelong Wang ◽  
Xingyu Li ◽  
Haoyang Wu ◽  
Baorui Jia ◽  
Deyin Zhang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Fracture Toughness ◽  
Grain Size ◽  
Flexural Strength ◽  
Grain Boundaries ◽  
Carbothermal Reduction ◽  
Secondary Phase ◽  
Gas Pressure ◽  
Gas Pressure Sintering

Abstract Si3N4-based ceramic (Si3N4-5wt%Y2O3-3wt%MgO) was obtained from carbothermal-reduction-derived powder combined with gas pressure sintering. The phase, microstructure, thermal conductivity and mechanical properties of Si3N4 ceramics were comprehensively analyzed. Dense Si3N4 ceramic with uniform grain size was obtained after sintering at 1900°C for 7 h under a N2 pressure of 1.2 MPa. The secondary phase consisted of Y4Si2O7N2 and Y2Si3O3N4 was found to gather around triangular grain boundaries. The thermal conductivity, flexural strength, hardness and fracture toughness of the Si3N4 ceramics were 95.7 W·m-1·k-1, 715 MPa, 17.2 GPa and 7.2 MPa·m1/2, respectively. The results were compared with product derived from commercial powder, the improvement of thermal conductivity (~8.3%) and fracture toughness (~4.3%) demonstrating the superiority of Si3N4 ceramics prepared from carbothermal-reduction-derived powder.

Sign in / Sign up

Export Citation Format

Share Document