scholarly journals Finite Element Analysis and Experimental Evaluation of Residual Stress of Zr-4 alloys Processed through Swaging

Metals ◽  
2020 ◽  
Vol 10 (10) ◽  
pp. 1281 ◽  
Author(s):  
Gaurav Singh ◽  
Bijit Kalita ◽  
K. I. Vishnu Narayanan ◽  
Umesh Kumar Arora ◽  
Manas M. Mahapatra ◽  
...  
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Nuclear Power ◽  
Zirconium Alloy ◽  
True Strain ◽  
Three Dimensional ◽  
Element Model ◽  
Hole Drilling ◽  
Element Analysis ◽  
Hole Drilling Method

Zirconium alloy has been extensively used as a cladding material in nuclear power reactors due to its low neutron absorption cross section, excellent mechanical properties, and corrosion resistance. The influence of the swaging parameter, feed rate (0.7, 1.25, 2 m/min) on residual stress induced in Zr-4 alloy is investigated in the present work. A three-dimensional finite element model was implemented in the Deform 3D software to simulate the rotary swaging (RS) process over a circular rod of Zr-4 alloy. The simulation results based on the 3D framework provide a detailed insight of residual stress, true stress versus true strain and force applied over the rod during the multiple pass swaging process; the results are compared with experimental results. The experimental hole drilling method is used to determine the residual stresses on swaged zirconium alloy at different feed rates (0.7, 1.25, and 2 m/min). A similar trend of residual stress between experimental and numerical results from the surface to the center on the swaged rod samples is observed. The same magnitude of residual stress at the surface of the swaged Zr-4 rod is also observed. It is found to be compressive at the surface and tensile in the center of the samples, as observed in the present work.

scholarly journals Finite element and biomechanical analysis of risk factors for implant failure during tension band plating

2020 ◽  
Vol 48 (11) ◽  
pp. 030006052097207
Author(s):  
Jing Ding ◽  
Fei Wang ◽  
Fangchun Jin ◽  
Zhen-kai Wu ◽  
Pin-quan Shen
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Finite Element Model ◽  
Three Dimensional ◽  
Biomechanical Model ◽  
Element Model ◽  
Tension Band ◽  
Biomechanical Analysis ◽  
Implant Failure ◽  
Element Analysis

Objective Tension band plating has recently gained widespread acceptance as a method of correcting angular limb deformities in skeletally immature patients. We examined the role of biomechanics in procedural failure and devised a new method of reducing the rate of implant failure. Methods In the biomechanical model, afterload (static or cyclic) was applied to each specimen. The residual stress of the screw combined with different screw sizes and configurations were measured and compared by X-ray diffraction. With regard to static load and similar conditions, the stress distribution was analyzed according to a three-dimensional finite element model. Results The residual stress was close to zero in the static tension group, whereas it was very high in the cyclic load group. The residual stress of screws was significantly lower in the convergent group and parallel group than in the divergent group. The finite element model showed similar results. Conclusions In both the finite element analysis and biomechanical tests, the maximum stress of the screw was concentrated at the position where the screws enter the cortex. Cyclic loading is the primary cause of implant failure.

Three Dimensional Finite Element Analysis of a Split-Sleeve Cold Expansion Process

2009 ◽  
Vol 131 (3) ◽  
Author(s):  
S. Ismonov ◽  
S. R. Daniewicz ◽  
J. C. Newman ◽  
M. R. Hill ◽  
M. R. Urban
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Residual Stress Field ◽  
Expansion Process ◽  
Element Analysis ◽  
Cold Expansion ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

A cold expansion process is used to prolong the fatigue life of a structure under cyclic loadings. The process produces a beneficial compressive residual stress zone in the hole vicinity, which retards the initiation and propagation of the crack at the hole edge. In this study, a three-dimensional finite element model of the split-sleeve cold expansion process was developed to predict the resulting residual stress field. A thin rectangular aluminum sheet with a centrally located hole was considered. A rigid mandrel and an elastic steel split sleeve were explicitly modeled with the appropriate contact elements at the interfaces between the mandrel, the sleeve, and the hole. Geometrical and material nonlinearities were included. The simulation results were compared with experimental measurements of the residual stress. The influence of friction and the prescribed boundary conditions for the sheet were studied. Differences between the split-sleeve- and the non-split-sleeve model solutions are discussed.

3D Finite Element Analysis of Prestressed Cutting

2012 ◽  
Vol 591-593 ◽  
pp. 766-770 ◽  
Author(s):  
Rui Tao Peng ◽  
Fang Lu ◽  
Xin Zi Tang ◽  
Yuan Qiang Tan
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Bearing Steel ◽  
Arbitrary Lagrangian Eulerian ◽  
Machined Surface ◽  
Element Analysis ◽  
Simulation Techniques ◽  
Ale Formulation

In order to reveal the adjustment principle of prestressed cutting on the residual stress of hardened bearing steel GCr15, a three-dimensional thermal elastic-viscoplastic finite element model was developed using an Arbitrary Lagrangian Eulerian (ALE) formulation. Several key simulation techniques including the material constitutive model, constitutive damage law and contact with friction were discussed, simulation of chip formation during prestressed cutting was successfully conducted. At the prestresses of 0 MPa, 341 MPa and 568 MPa, distributions of residual stress on machined surface were simulated and experimentally verified. The results indicated that residual compressive stress on machined surface were achieved and actively adjusted by utilizing the prestressed cutting method; meanwhile, within the elastic limit of bearing steel material, the higher applied prestress leads to the more prominent compressive residual stress in the surface layer and subsequently the higher fatigue resistance of the part.

Residual Stress Finite Element Analysis and Measurements of a Tube Penetration J-Groove Attachment Weld in a Hemispherical Head of a Large Ferritic Pressure Vessel: Part II — Outer Nozzle

2006 ◽  
Author(s):  
R. Dennis ◽  
N. Leggatt ◽  
C. T. Watson ◽  
E. Kingston ◽  
D. J. Smith
Keyword(s):  
Residual Stress ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Finite Element Model ◽  
Pressure Vessel ◽  
Element Model ◽  
Hole Drilling ◽  
Poor Correlation ◽  
Element Analysis ◽  
The Finite Element Model

A programme of work was undertaken to gain an understanding of the residual stress levels in the tube penetration J-groove welds in a hemispherical head of a large stainless steel clad ferritic pressure vessel. This second part of a two-part paper describes the finite element analysis that was carried out to model an off-centre outer tube to vessel head weld. A 3D finite element residual stress model was developed. The complex bead deposition sequence of the actual weld was simulated by a bead lumping approach using 9 passes. The results from the finite element analyses were compared with both surface and through thickness stress measurements. These measurements were taken on a mock weld that was representative of the actual component. The surface measurements were taken by using an incremental centre hole drilling technique. The through thickness values were obtained from deep hole drilling measurements at three positions around the circumference of the weld. For this off-centre penetration the cladding process was not modelled nor was clad applied to the test mock-up. The finite element results and the measured values showed similar trends in the variation of stress around the circumference of the weld. A poor correlation between measurements and analytical results was obtained at the lower hillside position. A major reason for the discrepancy is believed to be that the bead lumping approach that was used in the finite element model was not a sufficiently refined representation of the actual weld bead deposition sequence. Note however that one of the aims of this finite element analysis was to quantify the variations between the centre tube presented in the first part of this paper and the off centre tube presented here. In this regard the finite element model and measurements compared well. The finite element model was also used to carry out two sensitivity studies that investigated the effects upon residual stress of tube geometry and material properties. For the case where a nozzle tube was extended significantly below the vessel head inner surface the results showed the stresses to be significantly higher than the baseline case.

Torsional Analysis of a Steel Cord-Rubber Tire Belt Structure

1996 ◽  
Vol 24 (4) ◽  
pp. 339-348 ◽  
Author(s):  
R. M. V. Pidaparti
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Composite Structures ◽  
Three Dimensional ◽  
Element Model ◽  
Torsional Stiffness ◽  
Element Analysis ◽  
Rubber Belt ◽  
Steel Cord ◽  
Torsional Analysis

Abstract A three-dimensional (3D) beam finite element model was developed to investigate the torsional stiffness of a twisted steel-reinforced cord-rubber belt structure. The present 3D beam element takes into account the coupled extension, bending, and twisting deformations characteristic of the complex behavior of cord-rubber composite structures. The extension-twisting coupling due to the twisted nature of the cords was also considered in the finite element model. The results of torsional stiffness obtained from the finite element analysis for twisted cords and the two-ply steel cord-rubber belt structure are compared to the experimental data and other alternate solutions available in the literature. The effects of cord orientation, anisotropy, and rubber core surrounding the twisted cords on the torsional stiffness properties are presented and discussed.

Finite Element Analysis of Nonuniformity of Tires with Imperfections5

2007 ◽  
Vol 35 (3) ◽  
pp. 226-238 ◽  
Author(s):  
K. M. Jeong ◽  
K. W. Kim ◽  
H. G. Beom ◽  
J. U. Park
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Radial Force ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Force Variation ◽  
Three Dimensional Finite Element

Abstract The effects of variations in stiffness and geometry on the nonuniformity of tires are investigated by using the finite element analysis. In order to evaluate tire uniformity, a three-dimensional finite element model of the tire with imperfections is developed. This paper considers how imperfections, such as variations in stiffness or geometry and run-out, contribute to detrimental effects on tire nonuniformity. It is found that the radial force variation of a tire with imperfections depends strongly on the geometrical variations of the tire.

scholarly journals Comparison of Tooth- and Bone-Borne Appliances on the Stress Distributions and Displacement Patterns in the Facial Skeleton in Surgically Assisted Rapid Maxillary Expansion—A Finite Element Analysis (FEA) Study

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1152
Author(s):  
Rafał Nowak ◽  
Anna Olejnik ◽  
Hanna Gerber ◽  
Roman Frątczak ◽  
Ewa Zawiślak
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Rapid Maxillary Expansion ◽  
Stress Distributions ◽  
Maxillary Expansion ◽  
Facial Skeleton ◽  
Element Analysis ◽  
Maxillary Constriction

The aim of this study was to compare the reduced stresses according to Huber’s hypothesis and the displacement pattern in the region of the facial skeleton using a tooth- or bone-borne appliance in surgically assisted rapid maxillary expansion (SARME). In the current literature, the lack of updated reports about biomechanical effects in bone-borne appliances used in SARME is noticeable. Finite element analysis (FEA) was used for this study. Six facial skeleton models were created, five with various variants of osteotomy and one without osteotomy. Two different appliances for maxillary expansion were used for each model. The three-dimensional (3D) model of the facial skeleton was created on the basis of spiral computed tomography (CT) scans of a 32-year-old patient with maxillary constriction. The finite element model was built using ANSYS 15.0 software, in which the computations were carried out. Stress distributions and displacement values along the 3D axes were found for each osteotomy variant with the expansion of the tooth- and the bone-borne devices at a level of 0.5 mm. The investigation showed that in the case of a full osteotomy of the maxilla, as described by Bell and Epker in 1976, the method of fixing the appliance for maxillary expansion had no impact on the distribution of the reduced stresses according to Huber’s hypothesis in the facial skeleton. In the case of the bone-borne appliance, the load on the teeth, which may lead to periodontal and orthodontic complications, was eliminated. In the case of a full osteotomy of the maxilla, displacements in the buccolingual direction for all the variables of the bone-borne appliance were slightly bigger than for the tooth-borne appliance.

Stress and Fatigue Life Modeling of Cannon Breech Closures Including Effects of Material Strength and Residual Stress

2000 ◽  
Vol 123 (1) ◽  
pp. 150-154
Author(s):  
John H. Underwood ◽  
Michael J. Glennon
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Fatigue Life ◽  
Yield Strength ◽  
Residual Stresses ◽  
Solid Mechanics ◽  
Element Model ◽  
Pressure Vessels ◽  
Material Strength ◽  
Element Analysis

Laboratory fatigue life results are summarized from several test series of high-strength steel cannon breech closure assemblies pressurized by rapid application of hydraulic oil. The tests were performed to determine safe fatigue lives of high-pressure components at the breech end of the cannon and breech assembly. Careful reanalysis of the fatigue life tests provides data for stress and fatigue life models for breech components, over the following ranges of key parameters: 380–745 MPa cyclic internal pressure; 100–160 mm bore diameter cannon pressure vessels; 1040–1170 MPa yield strength A723 steel; no residual stress, shot peen residual stress, overload residual stress. Modeling of applied and residual stresses at the location of the fatigue failure site is performed by elastic-plastic finite element analysis using ABAQUS and by solid mechanics analysis. Shot peen and overload residual stresses are modeled by superposing typical or calculated residual stress distributions on the applied stresses. Overload residual stresses are obtained directly from the finite element model of the breech, with the breech overload applied to the model in the same way as with actual components. Modeling of the fatigue life of the components is based on the fatigue intensity factor concept of Underwood and Parker, a fracture mechanics description of life that accounts for residual stresses, material yield strength and initial defect size. The fatigue life model describes six test conditions in a stress versus life plot with an R2 correlation of 0.94, and shows significantly lower correlation when known variations in yield strength, stress concentration factor, or residual stress are not included in the model input, thus demonstrating the model sensitivity to these variables.

Research on the Effects of Welding Sequence on Welding Residual Stress of High-Speed Train Based on SYSWELD

2011 ◽  
Vol 399-401 ◽  
pp. 1806-1811
Author(s):  
Yong Hong Chen ◽  
Peng Chen ◽  
Ai Qin Tian
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
High Speed ◽  
Element Model ◽  
Welding Residual Stress ◽  
High Speed Train ◽  
Distribution Law ◽  
Element Analysis ◽  
Welding Sequence ◽  
Maximum Residual Stress

The finite element model of the roof of aluminum high-speed train was established, double ellipsoid heat source was employed, and heat elastic-plastic theory was used to simulate welding residual stress of the component under different welding sequence based on the finite element analysis software SYSWELD. The distribution law of welding residual stress was obtained. And the effects of the welding sequence on the value and distribution of residual stress was analyzed. The numerical results showed that the simulation data agree well with experimental test data. The maximum residual stress appears in the weld seam and nearby. The residual stress value decreases far away from the welding center. Welding sequence has a significant impact on the final welding residual stress when welding the roof of aluminum body. The side whose residual stress needs to be controlled should be welded first.

Three-Dimensional Finite Element Analysis of Residual Stress in Arteries

2004 ◽  
Vol 32 (2) ◽  
pp. 257-263 ◽  
Author(s):  
M. L. Raghavan ◽  
S. Trivedi ◽  
A. Nagaraj ◽  
D. D. McPherson ◽  
K. B. Chandran
Keyword(s):  
Residual Stress ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Analysis ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element
Sign in / Sign up

Export Citation Format

Share Document