scholarly journals On the Effect of Electron Beam Melted Ti6Al4V Part Orientations during Milling

Metals ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1172
Author(s):  
Abdulmajeed Dabwan ◽  
Saqib Anwar ◽  
Ali M. Al-Samhan ◽  
Mustafa M. Nasr
Keyword(s):  
Surface Roughness ◽  
Electron Beam ◽  
Surface Morphology ◽  
Surface Quality ◽  
Cutting Speed ◽  
Chip Morphology ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Machined Surface ◽  
Radial Depth

The machining of the electron beam melting (EBM) produced parts is a challenging task because, upon machining, different part orientations (EBM layers’ orientations) produce different surface quality even when the same machining parameters are employed. In this paper, the EBM fabricated parts are machined in three possible orientations with regard to the tool feed direction, where the three orientations are “tool movement in a layer plane” (TILP), “tool movement perpendicular to layer planes” (TLP), and “tool movement parallel to layers planes” (TPLP). The influence of the feed rate, radial depth of cut, and cutting speed is studied on surface roughness, cutting force, micro-hardness, microstructure, chip morphology, and surface morphology of Ti6Al4V, while considering the EBM part orientations. It was found that different orientations have different effects on the machined surface during milling. The results show that the EBM parts can achieve good surface quality and surface integrity when milled along the TLP orientation. For instance, surface roughness (Sa) can be improved up to 29% when the milling tool is fed along the TLP orientation compared to the other orientations (TILP and TPLP). Furthermore, surface morphology significantly improves with lower micro-pits, redeposited chips, and feed marks in case of the TLP orientation.

Cutting Forces and Surface Roughness in High-Speed End Milling of Ti6Al4V

2013 ◽  
Vol 589-590 ◽  
pp. 76-81
Author(s):  
Fu Zeng Wang ◽  
Jun Zhao ◽  
An Hai Li ◽  
Jia Bang Zhao
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Cutting Forces ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Wide Range ◽  
Radial Depth ◽  
Coated Carbide

In this paper, high speed milling experiments on Ti6Al4V were conducted with coated carbide inserts under a wide range of cutting conditions. The effects of cutting speed, feed rate and radial depth of cut on the cutting forces, chip morphologies as well as surface roughness were investigated. The results indicated that the cutting speed 200m/min could be considered as a critical value at which both relatively low cutting forces and good surface quality can be obtained at the same time. When the cutting speed exceeds 200m/min, the cutting forces increase rapidly and the surface quality degrades. There exist obvious correlations between cutting forces and surface roughness.

Investigation of Surface Characteristics and Chip Morphology in High Speed Cutting of Inconel718 Based on SHPB System

2019 ◽  
Author(s):  
Zengqiang Wang ◽  
Zhanfei Zhang ◽  
Wenhu Wang ◽  
Ruisong Jiang ◽  
Kunyang Lin ◽  
...  
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
Split Hopkinson Pressure Bar ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Surface Profile ◽  
Chip Morphology ◽  
Depth Of Cut ◽  
Machined Surface ◽  
High Speed Cutting

Abstract High speed cutting (HSC) technology has the characteristics of high material removal rates and high machining precision. In order to study the relationships between chip morphology and machining surface characteristic in high speed cutting of superalloy Inconel718. High-speed orthogonal cutting experiment are carried out by used a high speed cutting device based on split Hopkinson pressure bar (SHPB). The specimen surfaces and collected chips were then detected with optical microscope, scanning electron microscope and three-dimensional surface profile measuring instrument. The results show that within the experimental parameters (cutting speed from 8–16m/s, depth of cut 0.1–0.5mm), the obtained chips are sawtooth chips and periodic micro-ripple appear on the machined surface. With the cutting speed increases, machining surface roughness is decreases from 1.4 to 0.99μm, and the amplitude of periodic ripples also decreases. With the cutting depth increases, the machining surface roughness increases from 0.96 to 5.12μm and surface topography becomes worse. With the increase of cutting speed and depth of cut, the chips are transform from continues sawtooth to sawtooth fragment. By comparing the frequency of surface ripples and sawtooth chips, it is found that they are highly consistent.

The Effect of Cutting Speed and Feed Rate on Surface Roughness and Tool Wear when Machining Machining D2 Steel

2017 ◽  
Vol 909 ◽  
pp. 80-85 ◽  
Author(s):  
Mohd Rasidi Ibrahim ◽  
Tharmaraj Sreedharan ◽  
Nurul Aisyah Fadhlul Hadi ◽  
Mohammad Sukri Mustapa ◽  
Al Emran Ismail ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Surface Quality ◽  
Feed Rate ◽  
Input Parameter ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
D2 Steel

Machining parameters is a main aspect in performing turning operations using lathe machines. Cutting parameters such as cutting speed, feed rate and depth of cut gives big influence on the dynamic behavior of the machining system. In machining parts, surface quality and tool wear are the most crucial customer requirements. This is because the major indication of surface quality on machined part is the surface roughness and the value of tool wear. Hence, to improve the surface roughness and minimize the forming of tool wear, the optimum feed rate and cutting speed will be determined. The input parameter such as cutting speed, feed rate and depth of cut always influence the tool wear, surface roughness, cutting force, cutting temperature, tool life and dimensional accuracy. The D2 steel was being investigated from the perspective of the effect of cutting speed and feed rate on its surface roughness and tool wear. The results show that cutting speed is the main parameter which affects the surface roughness where the most optimum parameter would be at cutting speed of 173, 231 and 288 m/min with feed rate of 0.15 mm/rev. The tool wear strongly affected by feed rate where at 0.15 mm/rev the tool wear value is the lowest. The combination of high cutting speed and low feed rate was the best parameter to achieve smooth surface roughness.

Influence of Machining Parameters on the Surface Quality of Technical Plastics

2021 ◽  
Vol 105 (1) ◽  
pp. 381-389
Author(s):  
David Dobrocky ◽  
Josef Sedlak ◽  
Zdenek Joska ◽  
Jiri Prochazka ◽  
Zbynek Studeny ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Electrical Engineering ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Thermoplastic Polymer ◽  
Process Fluid ◽  
Electronics And Electrical

The article deals with the evaluation of the influence of conventional methods of machining on the surface quality of selected technical plastics. The thermoplastic polymer polyoximethylene (POM-C) Ertacetal C and polyamide (PA 6) Ertalon 6SA were selected for machining. Both materials are suitable for machining and are used for the production of precision mechanical components (e.g. gears, plain bearings, guides, etc.), but also in electronics and electrical engineering. In all these applications, the quality of machined surfaces is important, especially for functional surfaces that interact with other surfaces. Test specimens from these materials were turned and milled. The technological conditions of machining (revolutions per minute n, cutting speed vc , feed f, depth of cut ap ) were adapted to achieve approximately the same surface roughness values. The milled samples were machined with and without cooling medium (for drought). Turning was performed only dry. As the cutting speed vc increased, the surface roughness of the turned Ertacetal C material decreased, while milling led to a deterioration in the roughness as the cutting speed vc increased. Similar behavior was observed for Ertalon 6SA. The process fluid led to a deterioration in the roughness of the milled surfaces of both plastics. Turned surfaces showed worse roughness than milled surfaces.

scholarly journals Molecular Dynamics Investigation of Residual Stress and Surface Roughness of Cerium under Diamond Cutting

Micromachines ◽  
2018 ◽  
Vol 9 (8) ◽  
pp. 386 ◽  
Author(s):  
Yao Li ◽  
Maobing Shuai ◽  
Junjie Zhang ◽  
Haibing Zheng ◽  
Tao Sun ◽  
...  
Keyword(s):  
Molecular Dynamics ◽  
Residual Stress ◽  
Surface Roughness ◽  
Surface Quality ◽  
Depth Of Cut ◽  
Formation Mechanisms ◽  
Machining Parameters ◽  
Diamond Cutting ◽  
Machined Surface ◽  
Machined Surface Quality

Machined surface quality in terms of residual stress and surface roughness has an important influence on the performance of devices and components. In the present work, we elucidate the formation mechanisms of residual stress and surface roughness of single crystalline cerium under ultraprecision diamond cutting by means of molecular dynamics simulations. Influences of machining parameters, such as the rake angle of a cutting tool, depth of cut, and crystal orientation of the workpiece on the machined surface quality were also investigated. Simulation results revealed that dislocation activity and lattice distortion are the two parallel factors that govern the formation of both residual stress and surface roughness. It was found that both distributions of residual stress and surface roughness of machined surface are significantly affected by machining parameters. The optimum machining parameters for achieving high machined surface quality of cerium by diamond cutting are revealed.

Optimization of Milling Parameter for Untreated and Heat Treated Polyetheretherketones (PEEK) Biomaterials

2015 ◽  
Vol 761 ◽  
pp. 293-297
Author(s):  
Raja Izamshah ◽  
A. Yu Lung ◽  
Effendi Mohamad ◽  
Mohd Asyadi Azam ◽  
Mohd Amri ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Spindle Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Machined Surface ◽  
Heat Treated ◽  
Machining Parameter

Polyetheretherketones (PEEK) have been widely used as biomaterials for trauma, orthopedics and spinal implants. However, machining of this material poses several challenges such as rough machined surface which can affect the implant functional application. This research attempts to optimize the machining parameter (cutting speed, feed rate and depth of cut) for effectively machining Polyetheretherketones (PEEK) implant material using carbide cutting tools. Apart from optimizing machining parameters, effects of annealing condition on PEEK towards surface qualities are discuss. Response Surface Methodology (RSM) technique was used to evaluate the effects of the parameters and their interaction towards the ability of the optimum conditions. Based on the analysis results, the optimal machining parameter to obtain the smallest surface roughness values were by using spindle speed of 5754 rpm, feed rate of 0.026 mm/tooth and 5.11 mm depth of cut for un-annealed PEEK. As for the annealed PEEK to get the smallest surface roughness values were by using spindle speed of 5865 rpm, feed rate of 0.025 mm/tooth and 2 mm depth of cut.

scholarly journals Investigation on the Surface Quality Obtained during Trochoidal Milling of 6082 Aluminum Alloy

Machines ◽  
2021 ◽  
Vol 9 (4) ◽  
pp. 75
Author(s):  
Nikolaos E. Karkalos ◽  
Panagiotis Karmiris-Obratański ◽  
Szymon Kurpiel ◽  
Krzysztof Zagórski ◽  
Angelos P. Markopoulos
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Process Parameters ◽  
Manufacturing Industry ◽  
High Surface ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Surface Quality ◽  
Trochoidal Milling

Surface quality has always been an important goal in the manufacturing industry, as it is not only related to the achievement of appropriate geometrical tolerances but also plays an important role in the tribological behavior of the surface as well as its resistance to fatigue and corrosion. Usually, in order to achieve sufficiently high surface quality, process parameters, such as cutting speed and feed, are regulated or special types of cutting tools are used. In the present work, an alternative strategy for slot milling is adopted, namely, trochoidal milling, which employs a more complex trajectory for the cutting tool. Two series of experiments were initially conducted with traditional and trochoidal milling under various feed and cutting speed values in order to evaluate the capabilities of trochoidal milling. The findings showed a clear difference between the two milling strategies, and it was shown that the trochoidal milling strategy is able to provide superior surface quality when the appropriate process parameters are also chosen. Finally, the effect of the depth of cut, coolant and trochoidal stepover on surface roughness during trochoidal milling was also investigated, and it was found that lower depths of cut, the use of coolant and low values of trochoidal stepover can lead to a considerable decrease in surface roughness.

A Comprehensive Study on Surface Roughness in Machining of AISI D2 Hardened Steel

2012 ◽  
Vol 576 ◽  
pp. 60-63 ◽  
Author(s):  
N.A.H. Jasni ◽  
Mohd Amri Lajis
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Hardened Steel ◽  
Depth Of Cut ◽  
Feed Speed ◽  
Radial Depth ◽  
Aisi D2 ◽  
Coated Carbide

Hard milling of hardened steel has wide application in mould and die industries. However, milling induced surface finish has received little attention. An experimental investigation is conducted to comprehensively characterize the surface roughness of AISI D2 hardened steel (58-62 HRC) in end milling operation using TiAlN/AlCrN multilayer coated carbide. Surface roughness (Ra) was examined at different cutting speed (v) and radial depth of cut (dr) while the measurement was taken in feed speed, Vf and cutting speed, Vc directions. The experimental results show that the milled surface is anisotropic in nature. Surface roughness values in feed speed direction do not appear to correspond to any definite pattern in relation to cutting speed, while it increases with radial depth-of-cut within the range 0.13-0.24 µm. In cutting speed direction, surface roughness value decreases in the high speed range, while it increases in the high radial depth of cut. Radial depth of cut is the most influencing parameter in surface roughness followed by cutting speed.

EVALUATION OF SURFACE ROUGHNESS PRODUCED BY NANOCUTTING COPPER STRUCTURE USING A LEAST SQUARE MEAN METHOD

2019 ◽  
Vol 27 (01) ◽  
pp. 1950081 ◽  
Author(s):  
CHUNHUI JI ◽  
SHUANGQIU SUN ◽  
BIN LIN ◽  
TIANYI SUI
Keyword(s):  
Surface Roughness ◽  
Cutting Speed ◽  
Least Square ◽  
Depth Of Cut ◽  
Real Surface ◽  
Roughness Parameters ◽  
Machined Surface ◽  
Surface Roughness Parameters ◽  
3D Surface ◽  
3D Surface Roughness

This work performed molecular dynamic simulations to study the 2D profile and 3D surface topography in the nanometric cutting process. The least square mean method was used to model the evaluation criteria for the surface roughness at the nanometric scale. The result showed that the cutting speed was the most important factor influencing the spacing between the peaks, the sharpness of the peaks, and the randomness of the profile. The plastic deformation degree of the machined surface at the nanometric scale was significantly influenced by the cutting speed and depth of cut. The 2D and 3D surface roughness parameters exhibited a similar variation tendency, and the parameters Ra and Rq tended to increase gradually with an increase in the cutting speed and a decrease in the depth of cut. Finally, it is concluded that at the nanometric scale, the 3D surface roughness parameters could more accurately reflect the real surface characteristics than the 2D parameters.

Fractal-Based Analysis of the Relation Between Surface Finish and Machine Vibration in Milling Operation

2019 ◽  
Vol 19 (01) ◽  
pp. 2050006 ◽  
Author(s):  
Muhammad Owais Qadri ◽  
Hamidreza Namazi
Keyword(s):  
Surface Quality ◽  
Complex Structure ◽  
Vibration Signal ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Machined Surface ◽  
Machine Vibration ◽  
Milling Operation ◽  
Surface Changes

Analysis of surface quality of machined workpiece is an important issue in machining of materials. For this purpose, scientists analyze how the texture of machined surface changes due to different conditions. Machine vibration is one of the factors that highly affects the surface quality of machined surface. In this research, we analyze the relation between machine vibration and surface quality of machined workpiece. For this purpose, we employ fractal theory and analyze how the complex structure of machined surface changes with the complex structure of machine vibration signal in case of variations of machining parameters, namely, depth of cut, feed rate and spindle speed, in milling operation. Based on the results, variations of surface quality of machined workpiece are related with the variations of complexity of machine vibration signal. The method of analysis employed in this research can be applied to other machining operations in order to find the relation between machine vibration and surface quality of machined workpiece.

Sign in / Sign up

Export Citation Format

Share Document