scholarly journals Study on Plastic Deformation Behavior of Mo-10Ta under Ultra-High Strain Rate

Metals ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1153
Author(s):  
Ping Song ◽  
Wen-Bin Li ◽  
Yu Zheng ◽  
Jiu-Peng Song ◽  
Xiang-Cao Jiang ◽  
...  
Keyword(s):  
Activation Energy ◽  
High Strain Rate ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Deformation Behavior ◽  
High Strain ◽  
Rate Sensitivity ◽  
Strain Rate Range ◽  
Rate Range ◽  
Strain Relationship

This study investigated the deformation behavior of the Mo-10Ta alloy with a strain rate range of 102–105 s−1. The Split Hopkinson pressure bar (SHPB) experiments were conducted to investigate the influence of deformation conditions on the stress-strain relationship and strain rate sensitivity of the material within a strain rate range of 0.001–4500 s−1. The Shaped Charge Jet (SCJ) forming experiments under detonation loading was conducted to clarify the dynamic response and microstructure evolution of the material within an ultra-high strain rates range of 104–105 s−1. Based on the stress-strain relationship of Mo-10Ta alloy at high temperature (286–873 K) and high strain rate (460–4500 s−1), the influence of temperature and strain rate on the activation energy Q was analyzed. The results indicate that the material strain rate sensitivity increased with the increase in strain rate and strain. Meanwhile, the activation energy Q decreased as the temperature and strain rate increased. The plasticity of the Mo-10Ta alloy under the condition of SCJ forming was substantially enhanced compared with that under quasi-static deformation. The material grain was also refined under ultra-high strain rate, as reflected by the reduction in grain size from 232 μm to less than 10 μm.

High Strain Rate Deformation Behavior of Mg–Al–Zn Alloys at Elevated Temperatures

2007 ◽  
Vol 340-341 ◽  
pp. 107-112 ◽  
Author(s):  
Hiroyuki Watanabe ◽  
Koichi Ishikawa ◽  
Toshiji Mukai
Keyword(s):  
High Temperature ◽  
High Strain Rate ◽  
Strain Rate ◽  
Deformation Behavior ◽  
Elevated Temperatures ◽  
High Strain ◽  
Strain Rate Range ◽  
High Temperature Deformation ◽  
Temperature Deformation ◽  
Rate Range

High temperature deformation behavior of AZ31 and AZ91 magnesium alloys was examined by compression tests over a wide strain rate range from 10–3 to 103 s–1 with emphasis on the behavior at high strain rates. The dominant deformation mechanism in the low strain rate range below 10–1 s–1 was suggested to be climb-controlled dislocation creep. On the other hand, experimental results indicated that the deformation at a high strain rate of ~103 s–1 proceeds by conventional plastic flow of dislocation glide and twinning even at elevated temperatures. The solid-solution strengthening was operative for high temperature deformation at ~103 s–1.

High Strain Rate Compressive Behaviour of Selective Laser Melted Ti-6Al-4V

2017 ◽  
Vol 890 ◽  
pp. 323-326 ◽  
Author(s):  
Maziar Ramezani ◽  
Emmanuel Flores-Johnson ◽  
Lu Ming Shen ◽  
Thomas Neitzert
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Shear Failure ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Rate Sensitivity ◽  
Melting Process ◽  
Mechanical Tests ◽  
Hopkinson Pressure Bar

Ti-6Al-4V alloy is one of the most important engineering alloys, combining attractive properties with inherent workability. The aim of this study is to investigate the effect of strain rate on the compressive mechanical properties of Ti6Al4V alloy manufactured by a selective laser melting process. The mechanical tests were performed by means of a compression split Hopkinson pressure bar apparatus under high strain rate ranging from 1400 s-1 to 4500 s-1. The true stress-strain curves obtained from static and dynamic compressive tests show strain rate sensitivity from quasi-static (peak strength 1300MPa) to high strain rate (peak 1500 MPa). Within the high strain rate range tested, the strain rate sensitivity is not remarkable. The fractographic analysis shows a relatively smooth and smeared fractured surface along with a dimple like structure. The observation of elongated dimples confirms the operation of a dynamic shear failure mechanism for the additively manufactured Ti-6Al-4V parts.

scholarly journals Effect of Strain Rate on the Mechanical Properties of Cu/Ni Clad Foils

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 6846
Author(s):  
Haiyang Wang ◽  
Chuanjie Wang ◽  
Linfu Zhang ◽  
Gang Chen ◽  
Qiang Zhu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Rate Sensitivity ◽  
Interface Layer ◽  
Strain Rate Range ◽  
Coarse Grained ◽  
Uniaxial Tensile ◽  
Rate Range ◽  
Static Strain

The performance of clad foils in microforming deserves to be studied extensively, where the strain rate sensitivity of the clad foil concerning the forming performance is a crucial factor. In this paper, the strain rate sensitivity of the mechanical properties of coarse-grained (CG) Cu/Ni clad foils in the quasi-static strain rate range (ε˙=10−4 s−1~10−1 s−1) is explored by uniaxial tensile tests under different strain rates. The results show that the strength and ductility increase with strain rate, and the strain rate sensitivity m value is in the range of 0.012~0.015, which is three times the value of m for CG pure Cu. The fracture morphology shows that slip bands with different directions are entangled in localized areas near the interface layer. Molecular dynamics simulations demonstrate the formation of many edged dislocations at the Cu/Ni clad foils interface due to a mismatch interface. The improved ductility and strain rate sensitivity is attributed to the interaction and plugging of the edged dislocations with high density in the interface layer. Additionally, the influence of size effect on mechanical properties is consistently present in the quasi-static strain rate range. This paper helps to understand the strain rate sensitivity of CG clad foils and to develop clad foils in microforming processes.

Sign in / Sign up

Export Citation Format

Share Document