scholarly journals Acoustic Properties of 316L Stainless Steel Hollow Sphere Composites Fabricated by Pressure Casting

Metals ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 1047
Author(s):  
Chunhe Wang ◽  
Fengchun Jiang ◽  
Shuaiqi Shao ◽  
Tianmiao Yu ◽  
Chunhuan Guo
Keyword(s):  
Absorption Coefficient ◽  
Hollow Sphere ◽  
Sound Absorption ◽  
Random Distribution ◽  
Transmission Loss ◽  
Acoustic Properties ◽  
Sound Absorption Coefficient ◽  
Pressure Casting ◽  
Sound Transmission Loss ◽  
At Resonance

In this study, we prepared metal hollow sphere composites (MHSCs) using metal hollow spheres (MHSs) by pressure casting under vacuum conditions, and investigated the acoustic properties. The density of the MHSCs was measured using the mass to volume ratio, the microstructure of the MHSCs was observed using a scanning electron microscope, and the acoustic properties of the MHSCs were tested using an impedance tube. The measured MHSCs showed that the densities of the MHSCs with the random distribution of MHSs with diameter ~3.28 mm (1.74 g/cm3 to 1.77 g/cm3) (MHSC-3.28) were nearly equal to that of the MHSCs with the random distribution of MHSs with diameter ~5.76 mm (1.74 g/cm3 to 1.76 g/cm3) (MHSC-5.76), and lower than that of the MHSCs with the layered structure of MHSs with diameter ~3.28 mm (1.93 g/cm3 to 1.97 g/cm3) (MHSC-LS). Microstructural observations confirmed that the interface region between the MHSs and matrix demonstrated a simple physical combination pattern with pores. The acoustic properties of the MHSCs showed that the sound absorption coefficient of MHSC-LS was lower than that of MHSC-3.28 and higher than that of MHSC-5.76 at off-resonance. The sound absorption coefficient peak value of MHSC-3.28 was higher than that of MHSC-LS, and lower than that of MHSC-5.76 at resonance. The sound transmission loss of MHSC-3.28 was lower than that of MHSC-5.76, which shows the rules are independent from the resonance. The sound transmission loss of MHSC-LS was higher than that of MHSC-5.76 at resonance, but lower than that of MHSC-3.28 at off-resonance. In addition, we discuss the propagation mechanism of the sound waves in the MHSC, which is mainly determined by the distribution of the MHSs in the MHSC.

A study on the effects of compression of the felt on flow resistance and acoustic characteristics

2021 ◽  
Vol 263 (1) ◽  
pp. 5170-5174
Author(s):  
Yoon-sang Yang ◽  
Seung Lee
Keyword(s):  
Absorption Coefficient ◽  
Sound Absorption ◽  
Flow Resistance ◽  
Transmission Loss ◽  
Combustion Engine ◽  
Characteristic Impedance ◽  
Sound Transmission ◽  
Sound Absorption Coefficient ◽  
Sound Transmission Loss ◽  
Acoustic Characteristics

The sound absorbing materials used to reduce automobile interior noise are classified into Felt and PU Foam. Felt are widely used not only in internal combustion engine vehicles but also in Electric Vehicles because they are eco-friendly materials that can be recycled and relatively light. Automotive interior parts manufacture materials in various thicknesses depending on the shape of matched parts. The pressed material changes the density, flow resistance and affects the overall NVH performance of the vehicle. In this study we worked to confirm changes in flow resistance, sound absorption coefficient and sound transmission loss performance among acoustic characteristics based on the compress ratio of Felt. It was confirmed that the larger the compression of Felt, the larger the flow resistance value, thereby affecting the acoustic characteristic impedance, sound absorption coefficient and sound transmission loss.

scholarly journals Vibration Damping and Acoustic Behavior of PU-Filled Non-Stochastic Aluminum Cellular Solids

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 725
Author(s):  
Vitor Hugo Carneiro ◽  
Hélder Puga ◽  
José Meireles
Keyword(s):  
Absorption Coefficient ◽  
Sound Absorption ◽  
Transmission Loss ◽  
Polyurethane Foams ◽  
Vibration Damping ◽  
Acoustic Properties ◽  
Sound Absorption Coefficient ◽  
Cellular Solids ◽  
Infiltration Process ◽  
Wide Range

Aluminum-based cellular solids are promising lightweight structural materials considering their high specific strength and vibration damping, being potential candidates for future railway vehicles with enhanced riding comfort and low fuel consumption. The filling of these lattices with polymer-based (i.e., polyurethane) foams may further improve the overall vibration/noise-damping without significantly increasing their density. This study explores the dynamic (i.e., frequency response) and acoustic properties of unfilled and polyurethane-filled aluminum cellular solids to characterize their behavior and explore their benefits in terms of vibration and noise-damping. It is shown that polyurethane filling can increase the vibration damping and transmission loss, especially if the infiltration process uses flexible foams. Considering sound reflection, however, it is shown that polyurethane filled samples (0.27–0.30 at 300 Hz) tend to display lower values of sound absorption coefficient relatively to unfilled samples (0.75 at 600 Hz), is this attributed to a reduction in overall porosity, tortuosity and flow resistivity. Foam-filled samples (43–44 dB at 700–1200 Hz) were shown to be more suitable to reduce sound transmission rather than reflection than unfilled samples (21 dB at 700 Hz). It was shown that the morphology of these cellular solids might be optimized depending on the desired application: (i) unfilled aluminum cellular solids are appropriate to mitigate internal noises due to their high sound absorption coefficient; and (ii) PU filled cellular solids are appropriate to prevent exterior noises and vibration damping due to their high transmission loss in a wide range of frequencies and vibration damping.

scholarly journals Development of Impedance Tube to Measure Sound Absorption Coefficient

2019 ◽  
Vol 8 (6) ◽  
pp. 3218-3222
Keyword(s):  
Absorption Coefficient ◽  
Sound Absorption ◽  
Transmission Loss ◽  
Acoustic Property ◽  
Small Sample ◽  
Textile Material ◽  
Acoustic Properties ◽  
Sound Absorption Coefficient ◽  
Impedance Tube ◽  
Significant Difference

An acoustic property of textile material can be measured using an impedance tube, is the most popular technique to measure normal sound absorption and transmission loss. This method consuming less time and a very small sample is required to assess the acoustic properties of the materials. Unfortunately, the cost of the impedance tube and software used for measurement is very high. This paper gives information about how to develop a cost-effective impedance tube suitable for researchers. The design, development, and fabrication of the impedance tube suitable for different frequencies with technical details are present here. Information related to some software which can be used to measure sound absorption coefficient also provided. To validate the testing results obtained from custom-build impedance tube, same samples were tested on commercially available impedance tube at PSG College, Coimbatore. It was observed that both the instruments provide almost same results, no statistically significant difference found in results. Base on the results design of customized impedance tube recommends to student and researcher interested in measuring acoustic properties of textile material

scholarly journals Vibration damping and acoustic characteristics of sisal fibre–reinforced polypropylene composite

2018 ◽  
Vol 50 (1) ◽  
pp. 13-21 ◽  
Author(s):  
Yashwant S Munde ◽  
Ravindra B Ingle ◽  
I Siva
Keyword(s):  
Absorption Coefficient ◽  
Natural Frequency ◽  
Sound Absorption ◽  
Transmission Loss ◽  
Experimental Results ◽  
Acoustic Properties ◽  
Sound Absorption Coefficient ◽  
Polypropylene Composite ◽  
Acoustic Characteristics ◽  
Sisal Fibre

Natural fibre composites attract industries because of their low density, low cost and the specific mechanical properties they possess in comparison to synthetic fibres. In this work, the randomly oriented sisal fibre–reinforced polypropylene composites are fabricated using extrusion–injection moulding technique. The aim of this study is to experimentally investigate the effect of fibre weight fraction (0%–30% in step of 10%) on vibrational damping and acoustic characteristics. The impulse hammer excitation technique is used to evaluate the free vibrational characteristics, namely, natural frequency and damping. An impedance tube is used in evaluating the acoustic properties, namely, sound absorption coefficient and transmission loss. Experimental results reveal that increase in fibre loading significantly alter the vibrational and acoustic response of the polypropylene composite. Modal analysis shows that incorporation of sisal fibres by 30 wt.% to polypropylene made the natural frequency superior when compared with other compositions. However, damping becomes worse with higher fibre content. In case of acoustic properties, incorporation of fibres at higher fraction enhances the sound absorption coefficient and transmission loss. Experimental results drive the research in development of such new materials system towards the application of vibration and sound diminutions.

scholarly journals Non-Wovens as Sound Reducers

2018 ◽  
Vol 55 (2) ◽  
pp. 64-76
Author(s):  
D. Belakova ◽  
A. Seile ◽  
S. Kukle ◽  
T. Plamus
Keyword(s):  
Absorption Coefficient ◽  
Surface Density ◽  
Sound Absorption ◽  
Transmission Loss ◽  
Sound Transmission ◽  
Sound Insulation ◽  
Material Structure ◽  
Sound Transmission Loss ◽  
Sound Waves ◽  
Frequency Range

Abstract Within the present study, the effect of hemp (40 wt%) and polyactide (60 wt%), non-woven surface density, thickness and number of fibre web layers on the sound absorption coefficient and the sound transmission loss in the frequency range from 50 to 5000 Hz is analysed. The sound insulation properties of the experimental samples have been determined, compared to the ones in practical use, and the possible use of material has been defined. Non-woven materials are ideally suited for use in acoustic insulation products because the arrangement of fibres produces a porous material structure, which leads to a greater interaction between sound waves and fibre structure. Of all the tested samples (A, B and D), the non-woven variant B exceeded the surface density of sample A by 1.22 times and 1.15 times that of sample D. By placing non-wovens one above the other in 2 layers, it is possible to increase the absorption coefficient of the material, which depending on the frequency corresponds to C, D, and E sound absorption classes. Sample A demonstrates the best sound absorption of all the three samples in the frequency range from 250 to 2000 Hz. In the test frequency range from 50 to 5000 Hz, the sound transmission loss varies from 0.76 (Sample D at 63 Hz) to 3.90 (Sample B at 5000 Hz).

Sign in / Sign up

Export Citation Format

Share Document