scholarly journals Analysis of the Wall Geometry with Different Strategies for High Deposition Wire Arc Additive Manufacturing of Mild Steel

Metals ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 892 ◽  
Author(s):  
Eider Aldalur ◽  
Fernando Veiga ◽  
Alfredo Suárez ◽  
Jon Bilbao ◽  
Aitzol Lamikiz
Keyword(s):  
Additive Manufacturing ◽  
Gas Metal Arc Welding ◽  
Low Carbon Steel ◽  
Utilization Rate ◽  
High Deposition Rate ◽  
Low Carbon ◽  
Metal Arc Welding ◽  
Geometric Precision ◽  
Directed Energy ◽  
Wire Arc Additive Manufacturing

Additive manufacturing has gained relevance in recent decades as an alternative to the manufacture of metal parts. Among the additive technologies, those that are classified as Directed Energy Deposition (DED) are characterized by their high deposition rate, noticeably, Wire Arc Additive Manufacturing (WAAM). However, having the inability to produce parts with acceptable final surface quality and high geometric precision is to be considered an important disadvantage in this process. In this paper, different torch trajectory strategies (oscillatory motion and overlap) in the fabrication of low carbon steel walls will be compared using Gas Metal Arc Welding (GMAW)-based WAAM technology. The comparison is done with a study of the mechanical and microstructural characteristics of the produced walls and finally, addressing the productivity obtained utilizing each strategy. The oscillation strategy shows better results, regarding the utilization rate of deposited material and the flatness of the upper surface, this being advantageous for subsequent machining steps.

Wire arc additive manufacturing of thin-wall low-carbon steel parts: Microstructure and mechanical properties

2020 ◽  
Vol 34 (22n24) ◽  
pp. 2040154
Author(s):  
Van Thao Le ◽  
Tien Long Banh ◽  
Duc Toan Nguyen ◽  
Van Tao Le
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Carbon Steel ◽  
Heat Input ◽  
Low Carbon Steel ◽  
Production Costs ◽  
High Deposition Rate ◽  
Thin Wall ◽  
Low Carbon ◽  
Wire Arc Additive Manufacturing

Wire arc additive manufacturing (WAAM) has received much attention for manufacturing metal parts with medium and large dimensions because of its high deposition rate and low production costs. In this study, the effects of the heat input on the microstructure formation of thin-wall low-carbon steel parts built by a WAAM process were addressed. The mechanical properties of built materials were also studied. The results indicate that the heat input significantly influences on the shape of built thin walls, but has slight effects on the microstructure evolution of built materials. The WAAM thin-wall low-carbon steel presents suitable microstructures and good tensile strengths (YS: 320 – 362 MPa, UTS: 429 – 479 MPa) that are adequate with industrial applications.

scholarly journals Environmental Behavior of Low Carbon Steel Produced by a Wire Arc Additive Manufacturing Process

Metals ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 888 ◽  
Author(s):  
Ron ◽  
Levy ◽  
Dolev ◽  
Leon ◽  
Shirizly ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Additive Manufacturing ◽  
Carbon Steel ◽  
Stress Corrosion ◽  
Environmental Behavior ◽  
Low Carbon Steel ◽  
General Corrosion ◽  
Low Carbon ◽  
Corrosion Performance ◽  
Wire Arc Additive Manufacturing

: Current additive manufacturing (AM) processes are mainly focused on powder bed technologies, such as electron beam melting (EBM) and selective laser melting (SLM). However, the main disadvantages of such techniques are related to the high cost of metal powder, the degree of energy consumption, and the sizes of the components, that are limited by the size of the printing cell. The aim of the present study was to evaluate the environmental behavior of low carbon steel (ER70S-6) produced by a relatively inexpensive AM process using wire feed arc welding. The mechanical properties were examined by tension testing and hardness measurements, while microstructure was assessed by scanning electron microscopy and X-ray diffraction analysis. General corrosion performance was evaluated by salt spray testing, immersion testing, potentiodynamic polarization analysis, and electrochemical impedance spectroscopy. Stress corrosion performance was characterized in terms of slow strain rate testing (SSRT). All corrosion tests were carried out in 3.5% NaCl solution at room temperature. The results indicated that the general corrosion resistance of wire arc additive manufacturing (WAAM) samples were quite similar to those of the counterpart ST-37 steel and the stress corrosion resistance of both alloys was adequate. Altogether, it was clearly evident that the WAAM process did not encounter any deterioration in corrosion performance compared to its conventional wrought alloy counterpart.

scholarly journals Wire Arc Additive Manufacturing (WAAM) of Aluminum Alloy AlMg5Mn with Energy-Reduced Gas Metal Arc Welding (GMAW)

Materials ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 2671 ◽  
Author(s):  
Maximilian Gierth ◽  
Philipp Henckell ◽  
Yarop Ali ◽  
Jonas Scholl ◽  
Jean Pierre Bergmann
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Arc Welding ◽  
Energy Input ◽  
Large Scale ◽  
Unit Length ◽  
Gas Metal Arc Welding ◽  
Cold Metal Transfer ◽  
Metal Arc Welding ◽  
Wire Arc Additive Manufacturing

Large-scale aluminum parts are used in aerospace and automotive industries, due to excellent strength, light weight, and the good corrosion resistance of the material. Additive manufacturing processes enable both cost and time savings in the context of component manufacturing. Thereby, wire arc additive manufacturing (WAAM) is particularly suitable for the production of large volume parts due to deposition rates in the range of kilograms per hour. Challenges during the manufacturing process of aluminum alloys, such as porosity or poor mechanical properties, can be overcome by using arc technologies with adaptable energy input. In this study, WAAM of AlMg5Mn alloy was systematically investigated by using the gas metal arc welding (GMAW) process. Herein, correlations between the energy input and the resulting temperature–time-regimes show the effect on resulting microstructure, weld seam irregularities and the mechanical properties of additively manufactured aluminum parts. Therefore, multilayer walls were built layer wise using the cold metal transfer (CMT) process including conventional CMT, CMT advanced and CMT pulse advanced arc modes. These processing strategies were analyzed by means of energy input, whereby the geometrical features of the layers could be controlled as well as the porosity to area portion to below 1% in the WAAM parts. Furthermore, the investigations show the that mechanical properties like tensile strength and material hardness can be adapted throughout the energy input per unit length significantly.

Effect of Shielding Gas Mixture on Gas Metal Arc Welding (GMAW) of Low Carbon Steel (LR Grade A)

2016 ◽  
Vol 705 ◽  
pp. 250-254 ◽  
Author(s):  
Yustiasih Purwaningrum ◽  
Triyono ◽  
M. Wirawan Pu ◽  
Fandi Alfarizi
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Carbon Steel ◽  
Arc Welding ◽  
Gas Metal Arc Welding ◽  
Low Carbon Steel ◽  
Low Carbon ◽  
Shielding Gas ◽  
Weld Metals ◽  
Metal Arc Welding

The aimed of this research is to determine the feasibility and effect of the mixture of the shielding gas in the physical and mechanical properties. Low carbon steel LR grade A in a thickness 12 mm were joined in butt joint types using GMAW (Gas Metal Arc Welding) with groove’s gap 5 mm and groove angle’s 400 with variation of shielding gas composition. The composition of shielding gas that used were 100% Ar, 100 % CO2 and 50% Ar + 50 % CO2. The measured of mechanical properties with regard to strength, hardness and toughness using, tensile test, bending test, Vickers hardness Test, and Charpy impact test respectively. The physical properties examined with optical microscope. Results show that tensile strength of welding metals are higher than raw materials. Welds metal with mixing Ar + CO shielding gas has the highest tensile strength. Hardness of weld metals with the shielding gas 100% Ar, 100 % CO2 and 50% Ar + 50 % CO2 are 244.9; 209.4; and 209.4 VHN respectively. The temperature of Charpy test was varied to find the transition temperature of the materials. The temperature that used were –60°C, -40°C, -20°C, 0°C, 20°C , and room temperature. Weld metals with various shielding gas have similar trends of toughness flux that was corellated with the microstructure of weld .

scholarly journals Development of a Multidirectional Wire Arc Additive Manufacturing (WAAM) Process with Pure Object Manipulation: Process Introduction and First Prototypes

2021 ◽  
Vol 5 (4) ◽  
pp. 134
Author(s):  
Khushal Parmar ◽  
Lukas Oster ◽  
Samuel Mann ◽  
Rahul Sharma ◽  
Uwe Reisgen ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Gas Metal Arc Welding ◽  
Operating Conditions ◽  
Metal Arc Welding ◽  
Welding Torch ◽  
Building Process ◽  
Single Bead ◽  
Software Interfaces ◽  
Substrate Plate ◽  
Wire Arc Additive Manufacturing

Wire Arc Additive Manufacturing (WAAM) with eccentric wire feed requires defined operating conditions due to the possibility of varying shapes of the deposited and solidified material depending on the welding torch orientation. In consequence, the produced component can contain significant errors because single bead geometrical errors are cumulatively added to the next layer during a building process. In order to minimise such inaccuracies caused by torch manipulation, this article illustrates the concept and testing of object-manipulated WAAM by incorporating robotic and welding technologies. As the first step towards this target, robotic hardware and software interfaces were developed to control the robot. Alongside, a fixture for holding the substrate plate was designed and fabricated. After establishing the robotic setup, in order to complete the whole WAAM process setup, a Gas Metal Arc Welding (GMAW) process was built and integrated into the system. Later, an experimental plan was prepared to perform single and multilayer welding experiments as well as for different trajectories. According to this plan, several welding experiments were performed to decide the parametric working range for the further WAAM experiments. In the end, the results of the first multilayer depositions over intricate trajectories are shown. Further performance and quality optimization strategies are also discussed at the end of this article.

scholarly journals Vision-Based Melt Pool Monitoring for Wire-Arc Additive Manufacturing Using Deep Learning Method

2021 ◽  
Author(s):  
Chunyang Xia ◽  
Zengxi Pan ◽  
Yuxing Li ◽  
Huijun Li
Keyword(s):  
Deep Learning ◽  
Additive Manufacturing ◽  
Large Scale ◽  
Deposition Process ◽  
Utilization Rate ◽  
High Deposition Rate ◽  
Promising Alternative ◽  
Visual Monitoring ◽  
Melt Pool ◽  
Wire Arc Additive Manufacturing

Abstract Wire-arc additive manufacturing (WAAM) technology has been widely recognized as a promising alternative for fabricating large-scale components, due to its advantages of high deposition rate and high material utilization rate. However, some anomalies may occur during the deposition process, such as humping, spattering, and robot suspend. this study proposed to apply Deep Learning in the visual monitoring to diagnose different anomalies during WAAM process. The melt pool images of different anomalies were collected for training and validation by a visual monitoring system. The classification performance of several representative CNN architectures, including ResNet, EfficientNet, VGG-16 and GoogLeNet, were investigated and compared. The classification accuracy of 97.62%, 97.45%, 97.15% and 97.25% was achieved by each model. The results proved that the CNN models are effective in classifying different types of melt pool images of WAAM. Our study is applicable beyond WAAM and should benefit other additive manufacturing or arc welding techniques.

scholarly journals Gas Metal Arc Welding Modes in Wire Arc Additive Manufacturing of Ti-6Al-4V

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2457
Author(s):  
Oleg Panchenko ◽  
Dmitry Kurushkin ◽  
Fedor Isupov ◽  
Anton Naumov ◽  
Ivan Kladov ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Arc Welding ◽  
High Speed ◽  
Gas Metal Arc Welding ◽  
Metal Transfer ◽  
Process Data ◽  
Cold Metal Transfer ◽  
Wall Width ◽  
Metal Arc Welding ◽  
Wire Arc Additive Manufacturing

In wire arc additive manufacturing of Ti-alloy parts (Ti-WAAM) gas metal arc welding (GMAW) can be applied for complex parts printing. However, due to the specific properties of Ti, GMAW of Ti-alloys is complicated. In this work, three different types of metal transfer modes during Ti-WAAM were investigated: Cold Metal Transfer, controlled short circuiting metal transfer, and self-regulated metal transfer at a direct current with a negative electrode. Metal transfer modes were studied using captured waveform and high-speed video analysis. Using these modes, three walls were manufactured; the geometry preservation stability was estimated and compared using effective wall width calculation, the microstructure was analyzed using optical microscopy. Transfer process data showed that arc wandering depends not only on cathode spot instabilities, but also on anode processing properties. Microstructure analysis showed that each produced wall consists of phases and structures inherent for Ti-WAAM. α-basketweave in the center of and α-colony on the grain boundary of epitaxially grown β-grains were found with heat affected zone bands along the height of the walls, so that the microstructure did not depend on metal transfer dramatically. However, the geometry preservation stability was higher in the wall, produced with controlled short circuiting metal transfer.

scholarly journals EFFECTS OF WELDING CURRENT ON THE SHAPE AND MICROSTRUCTURE FORMATION OF THIN-WALLED LOW-CARBON PARTS BUILT BY WIRE ARC ADDITIVE MANUFACTURING

2020 ◽  
Vol 58 (4) ◽  
pp. 461
Author(s):  
Van Thao Le ◽  
Quang Huy Hoang ◽  
Van Chau Tran ◽  
Dinh Si Mai ◽  
Duc Manh Dinh ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Carbon Steel ◽  
Low Carbon Steel ◽  
Welding Current ◽  
Welding Parameters ◽  
Low Carbon ◽  
Microstructure Formation ◽  
Thin Walled ◽  
Wire Arc Additive Manufacturing

Wire arc additive manufacturing (WAAM) is nowadays gaining much attention from both the academic and industrial sectors for the manufacture of medium and large dimension metal parts because of its high deposition rate and low costs of equipment investment. In the literature, WAAM has been extensively investigated in terms of the shape and dimension accuracy of built parts. However, limited research has focused on the effects of welding parameters on the microstructural characteristics of parts manufactured by this process. In this paper, the effects of welding current in the WAAM process on the shape and the microstructure formation of built thin-walled low-carbon steel components were studied. For this purpose, the thin-walled low-carbon steel samples were built layer-by-layer on the substrates by using an industrial gas metal arc welding robot with different levels of welding current. The shape, microstructures and mechanical properties of built samples were then analyzed. The obtained results show that the welding current plays an important role in the shape stability, but does not significantly influence on the microstructure formation of built thin-walled samples. The increase of the welding current only leads to coarser grain size and resulting in decreasing the hardness of built materials in each zone of the built sample. The mechanical properties (hardness and tensile properties) of the WAAM-built thin-walled low-carbon steel parts are also comparable to those of wrought low-carbon steel, and to be adequate with real applications.

Sign in / Sign up

Export Citation Format

Share Document