scholarly journals Circumferential Material Flow in the Hydroforming of Overlapping Blanks

Metals ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 864 ◽  
Author(s):  
Cong Han ◽  
Hao Feng
Keyword(s):  
Material Flow ◽  
Thickness Distribution ◽  
Flow Distribution ◽  
304 Stainless Steel ◽  
Forming Limit ◽  
Forming Process ◽  
Aisi 304 ◽  
Variable Diameter ◽  
Middle Cross Section ◽  
Peak Value

The hydroforming of the overlapping blanks is a forming process where overlapping tubular blanks are used instead of tubes to enhance the forming limit and improve the thickness distribution. A distinguishing characteristic of the hydroforming of overlapping blanks is that the material can flow along the circumferential direction easily. In this research, the circumferential material flow was investigated using overlapping blanks with axial constraints to study the circumferential material flow in the hydroforming of a variable-diameter part. AISI 304 stainless steel blanks were selected for numerical simulation and experimental research. The circumferential material flow distribution was obtained from the profile at the edge of the overlap. The peak value located at the middle cross-section. In addition, the circumferential material flow could be also reflected in the variation of the overlap angle. The variation of the overlap angle kept increasing as the initial overlap angle increased but the improvement of the thickness distribution did not. There was an optimal initial overlap angle to minimize the thinning ratio. An optimal thickness distribution was obtained when the initial angle was 120° for the hydroforming of the variable-diameter part with an expansion of 31.6%.

scholarly journals Formability study and metallurgical properties analysis of FSWed AA 6061 blank by the SPIF process

2021 ◽  
Vol 3 (3) ◽  
Author(s):  
Payam Tayebi ◽  
Ali Fazli ◽  
Parviz Asadi ◽  
Mahdi Soltanpour
Keyword(s):  
Base Metal ◽  
Strain Distribution ◽  
Thickness Distribution ◽  
Experimental Studies ◽  
Welding Process ◽  
Forming Limit ◽  
Forming Process ◽  
Friction Stir ◽  
Numerical Process ◽  
Tailor Welded Blank

AbstractIn this study, in order to obtain the maximum possible formability in tailor-welded blank AA6061 sheets connected by the friction stir welding (FSW) procedure, the incremental sheet forming process has been utilized. The results are presented both numerically and experimentally. To obtain the forming limit angle, the base and FSWed sheets were formed in different angles with conical geometry, and ultimately, the forming limit angle for the base metal and FSWed sheet is estimated to be 60° and 57.5°, respectively. To explore the effects of welding and forming procedures on AA6061 sheets, experimental studies such as mechanical properties, microstructure and fracture analysis are carried out on the samples. Also, the thickness distribution of the samples is studied to investigate the effect of the welding process on the thickness distribution. Then, the numerical process was simulated by the ABAQUS commercial software to study the causes of the FSWed samples failure through analyzing the thickness distribution parameter, and major and minor strains and the strain distribution. Causes of failure in FSWed samples include increased minor strain, strain distribution and thickness distribution in welded areas, especially in the proximity of the base metal area.

Optimization of Sheet Metal Process Parameters of a Shield Case Piece Using Computer Simulation

2006 ◽  
Vol 510-511 ◽  
pp. 330-333
Author(s):  
M.C. Curiel ◽  
Ho Sung Aum ◽  
Joaquín Lira-Olivares
Keyword(s):  
Sheet Metal ◽  
Thickness Distribution ◽  
Forming Limit Diagram ◽  
Forming Limit ◽  
Physical Processes ◽  
Forming Process ◽  
Element Analysis ◽  
One Step ◽  
Range Of Values ◽  
Principal Strains

Numerical simulations based on Finite Element Analysis (FEA) are widely used to predict and evaluate the forming parameters before performing the physical processes. In the sheet metal industry, there are basically two types of FE programs: the inverse (one-step) programs and the incremental programs. In the present paper, the forming process of the shield case piece (LTA260W1-L05) was optimized by performing simulations with both types of software. The main analyzed parameter was the blankholding force while the rest of the parameters were kept constant. The criteria used to determine the optimum value was based on the Forming Limit Diagram (FLD), fracture and wrinkling of the material, thickness distribution, and the principal strains obtained. It was found that the holding force during the forming process deeply affects the results, and a range of values was established in which the process is assumed to give a good quality piece.

Study on the Forming Process of the Crossmember in Car Intermediate Floor

2013 ◽  
Vol 442 ◽  
pp. 593-598
Author(s):  
Xue Xia Wang ◽  
Peng Chong Guan ◽  
Hai Peng Li ◽  
Li Hui Wang ◽  
Na Zhang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Numerical Model ◽  
Process Parameters ◽  
Thickness Distribution ◽  
Forming Limit Diagram ◽  
Forming Limit ◽  
Simulation Technology ◽  
Forming Process ◽  
Distribution Diagram ◽  
Simulation Results

Flanging and bending forming processes of the crossmember in car intermediate floor are investigated respectively by using numerical simulation technology. The numerical model of the crossmember was established and its press forming effect was simulated to determine the feasible process parameters affecting its manufacturability. Forming limit diagram and thickness distribution diagram are used to evaluate simulation results of different process schemes. And then optimum values of process parameters for flanging and bending are found, which can reduce the tendencies of wrinkling, springback and crackling during the stamping of the product.

The Forming Process of the Sharply Curved Offsets by the Pushing Method

2016 ◽  
Vol 684 ◽  
pp. 242-252
Author(s):  
Valentin Dmitrievich Maslov ◽  
I.P. Popov ◽  
Valentin Dmitrievich Misyura
Keyword(s):  
Thickness Distribution ◽  
Steel Tube ◽  
304 Stainless Steel ◽  
Stainless Steel Tube ◽  
Curvature Radius ◽  
Distribution Law ◽  
Forming Process ◽  
Program Complex ◽  
Bending Process ◽  
Parts Manufacturing

The scheme of device for the thin-walled sharply curved offset parts forming by pushing the tube-shaped workpiece through the die channel is presented. The numerical simulation of the bending process by pushing the tube-shaped workpiece is performed using ANSYS-LS/DYNA program complex. The wall thickness distribution law along the generatrix of curved workpiece is determined. The influence of curvature radius of the curved offset part on thinning deformation during bending process is defined. The experimental determination of the AISI 304 stainless steel tube-shaped workpiece thickness changes is performed. Application of the developed device for the sharply curved offset parts manufacturing according to DIN/ISO standards is demonstrated.

Improvement of Wall Angle in AISI 304 Stainless Steel Cup using Five Stage Single Point Incremental Forming

2020 ◽  
Vol 12 (1) ◽  
Author(s):  
D. Suresh Kumar ◽  
N. Ethiraj
Keyword(s):  
Incremental Forming ◽  
Single Point ◽  
Research Work ◽  
Single Stage ◽  
304 Stainless Steel ◽  
Forming Process ◽  
Wall Angle ◽  
Aisi 304 ◽  
Metal Forming Process ◽  
Stage Process

Incremental forming is a non-conventional metal forming process which is widely used to produce the customized parts especially in medical and aerospace industries. One of the challenges encountered in the single stage process is the maximum wall angle of the component that can be formed to a maximum possible depth without fracture. Many strategies have been tried by the researchers in the past to overcome this limitation. The aim of this research work is to investigate the effect of 5 stage incremental forming process in improving the formation of maximum wall angle to a possible height which is not possible in single stage incremental forming. Also, the different strain measurements are carried out to identify the region at which the fracture is likely to occur in the produced part. It is observed from single stage incremental forming process for a wall angle of 64, max. depth of 45mm is achieved in the part produced. The current 5 stage incremental forming process reached the max. height of 54 mm with a wall angle of 76 successfully. The maximum thickness strain of 75% is observed at a distance of 18mm from the bottom end of the flange of a formed component.

Numerical Simulation of Bulging Process of Aluminum Alloy Sheet

2013 ◽  
Vol 327 ◽  
pp. 112-116 ◽  
Author(s):  
Mao Ting Li ◽  
Yong Zhang ◽  
Chui You Kong
Keyword(s):  
Aluminum Alloy ◽  
Material Flow ◽  
Thickness Distribution ◽  
Superplastic Forming ◽  
Alloy Sheet ◽  
Pressure Loading ◽  
Forming Process ◽  
Element Analysis ◽  
Danger Zone ◽  
Linear Finite Element

Basing on software MSC. Marc of non-linear finite element analysis, the article has studied the material flow in the process of aluminum alloy superplastic gas bulging forming. By analyzing of the thickness distribution of the molding member it confirm the danger zone in the forming process. By analyzing of pressure loading curve influence on forming part. Because the aluminum alloy is widely used in the industrial departments, it is supposed to improve the ability of forming ability of aluminum alloy by researching the superplastic forming.

Investigation on Forming Process of Automobile Trunk Side Panel Based on Numerical Simulation Technology

2013 ◽  
Vol 634-638 ◽  
pp. 2855-2860
Author(s):  
Hai Peng Li ◽  
Jia Wei Fan ◽  
Li Hui Wang ◽  
Xue Xia Wang ◽  
Ju Yuan Zhao
Keyword(s):  
Numerical Simulation ◽  
Process Parameters ◽  
Thickness Distribution ◽  
Forming Limit Diagram ◽  
Forming Limit ◽  
Simulation Technology ◽  
Forming Process ◽  
Distribution Diagram ◽  
Side Panel ◽  
Design Cycle

The forming process of automobile trunk side panel was investigated, using numerical simulation technology, to acquire the feasible process parameters and improve the formability of the product. With the technology, the manufacturability working procedures and drawing process parameters of the product were analyzed, calculated and simulated to achieve optimum formability characteristics. The method effectively lowers the probability of springback, wrinkling and thickness reduction, and shortens design cycle and cost. Based on the simulation results including forming limit diagram and thickness distribution diagram, the feasible process parameters are determined.

Experimental Study on Residual Formability of Single Point Incrementally Formed Part

2019 ◽  
Author(s):  
Chetan P. Nikhare
Keyword(s):  
Sheet Metal ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Incremental Forming ◽  
Thickness Distribution ◽  
Single Point ◽  
Forming Limit ◽  
Single Point Incremental Forming ◽  
Forming Process ◽  
Conventional Process

Abstract A substantial increase in demand on the sheet metal part usage in aerospace and automotive industries is due to the increase in the sale of these products to ease the transportation. However, due to the increase in fuel prices and further environmental regulation had left no choice but to manufacture more fuel efficient and inexpensive vehicles. These heavy demands force researchers to think outside the box. Many innovative research projects came to replace the conventional sheet metal forming of which single point incremental forming is one of them. SPIF is the emerging die-less sheet metal forming process in which the single point tool incrementally forces any single point of sheet metal at any processing time to undergo plastic deformation. It has several advantages over the conventional process like high process flexibility, elimination of die, complex shape and better formability. Previous literature provides enormous research on formability of metal during this process, process with various metals and hybrid metals, the influence of various process parameter, but residual formability after this process is untouched. Thus, the aim of this paper is to investigate the residual formability of the formed parts using single point incremental forming and then restrike with a conventional tool. The common process parameters of single point incremental forming were varied, and residual formability was studied through the conventional process. The strain and thickness distribution were measured and analyzed. In addition, the forming limit of the part was plotted and compared.

Influencing Factors of AZ31B Sheet Deep Drawing

2011 ◽  
Vol 189-193 ◽  
pp. 88-91
Author(s):  
Jun Gao ◽  
Zhen Ming Yue ◽  
Shu Xia Lin
Keyword(s):  
Numerical Simulation ◽  
Deep Drawing ◽  
Experimental Approach ◽  
Elevated Temperatures ◽  
Heating Temperature ◽  
Thickness Distribution ◽  
Simulation Software ◽  
Forming Limit ◽  
Forming Process ◽  
Specific Strength

Magnesium alloys have been attracting much more attentions due to its low density, high specific strength and its lightweight during the past 30 years. In this paper, the deep drawing performance of AZ31B magnisium alloy sheets at elevated temperature was studied by the experimental approach. The results indicated that the formability of the AZ31B sheets at elevated temperatures could be improved significantly. The best external forming parameters can be obtained such as heating temperature of sheet, die-punch clearance, punch fillet radius, etc. Simulating the forming process by using the numerical simulation software, we investigated the stress-strain distribution, thickness distribution and forming limit, etc. The thickness distribution by the numerical simulation agrees well with the experimental results.

Thermography IR Applied to Analyse the Influence of the Deformation Speed in the Forming Process

2014 ◽  
Vol 615 ◽  
pp. 76-81
Author(s):  
Manuel San Juán ◽  
Óscar Martín ◽  
Francisco Javier Santos ◽  
Pilar de Tiedra ◽  
Roberto López ◽  
...  
Keyword(s):  
Experimental Study ◽  
Stainless Steel ◽  
Tensile Test ◽  
304 Stainless Steel ◽  
Aisi 304 Stainless Steel ◽  
Forming Process ◽  
Temperature Variations ◽  
Aisi 304 ◽  
Thermographic Camera ◽  
Deformation Speed

This work presents the development of an experimental study which aims to establish arelationship of temperature variations, deformation speeds and the possible microstructural changes in the AISI 304 stainless steel. For this, an IR thermographic camera recorded serveral tensile test with different deformation speeds.

Sign in / Sign up

Export Citation Format

Share Document