scholarly journals Phase Transformation of High Velocity Air Fuel (HVAF)-Sprayed Al-Cu-Fe-Si Quasicrystalline Coating

Metals ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 834
Author(s):  
Mingwei Cai ◽  
Jun Shen
Keyword(s):  
Electron Microscopy ◽  
Phase Transformation ◽  
Amorphous Phase ◽  
High Velocity ◽  
Quasicrystalline Phase ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Heating And Cooling ◽  
Transmission Electron ◽  
The Difference

Al-Cu-Fe-Si quasicrystalline coatings were prepared by high velocity air fuel spraying to study their phase transformation during the process. The feedstock powder and coating were phase characterized by scanning electron microscopy, X-ray diffractometry, differential scanning calorimetry, and transmission electron microscopy. Results show that Al3Cu2 phase, a small amount of λ-Al13Fe4 phase, quasicrystalline phase (QC), amorphous phase, and β-Al (Cu, Fe, Si) phase were present in the sprayed Al50Cu20Fe15Si15 powder. For a typical flattened powder particle, the splat periphery was surrounded by a 1 µm thick amorphous phase. The inside area of the splat was composed of the QC covered by the Al3Cu2 and Si-rich β-Al (Cu, Fe, Si) phases. Another kind of Cu- rich β-Al (Cu, Fe, Si) phase can be found close to the amorphous area with a similar composition to the original β-Al (Cu, Fe, Si) phase in the powder. Different phases were observed when the periphery and inside area of the splat were compared. This result was caused by the difference in the heating and cooling rates.

scholarly journals Structural Characterization of Al65Cu20Fe15 Melt-Spun Alloy by X-ray, Neutron Diffraction, High-Resolution Electron Microscopy and Mössbauer Spectroscopy

Materials ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 54
Author(s):  
Rafał Babilas ◽  
Katarzyna Młynarek ◽  
Wojciech Łoński ◽  
Dariusz Łukowiec ◽  
Mariola Kądziołka-Gaweł ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Neutron Diffraction ◽  
Quasicrystalline Phase ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
Icosahedral Quasicrystalline Phase ◽  
Icosahedral Quasicrystalline

The aim of the work was to characterize the structure of Al65Cu20Fe15 alloy obtained with the use of conventional casting and rapid solidification-melt-spinning technology. Based on the literature data, the possibility of an icosahedral quasicrystalline phase forming in the Al-Cu-Fe was verified. Structure analysis was performed based on the results of X-ray diffraction, neutron diffraction, 57Fe Mössbauer and transmission electron microscopy. Studies using differential scanning calorimetry were carried out to describe the crystallization mechanism. Additionally, electrochemical tests were performed in order to characterize the influence of the structure and cooling rate on the corrosion resistance. On the basis of the structural studies, the formation of a metastable icosahedral phase and partial amorphous state of ribbon structure were demonstrated. The possibility of the formation of icosahedral quasicrystalline phase I-AlCuFe together with the crystalline phases was indicated by X-ray diffraction (XRD), neutron diffraction (ND) patterns, Mössbauer spectroscopy, high-resolution transmission electron microscopy (HRTEM) observations and differential scanning calorimetry (DSC) curves. The beneficial effect of the application of rapid solidification on the corrosive properties was also confirmed.

scholarly journals pH-controlled synthesis of sustainable lauric acid/SiO2 phase change material for scalable thermal energy storage

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Shafiq Ishak ◽  
Soumen Mandal ◽  
Han-Seung Lee ◽  
Jitendra Kumar Singh
Keyword(s):  
Electron Microscopy ◽  
Phase Change ◽  
Lauric Acid ◽  
Photoelectron Spectroscopy ◽  
Phase Change Materials ◽  
Precursor Solution ◽  
Thermal Reliability ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Heating And Cooling

AbstractLauric acid (LA) has been recommended as economic, eco-friendly, and commercially viable materials to be used as phase change materials (PCMs). Nevertheless, there is lack of optimized parameters to produce microencapsulated PCMs with good performance. In this study, different amounts of LA have been chosen as core materials while tetraethyl orthosilicate (TEOS) as the precursor solution to form silicon dioxide (SiO2) shell. The pH of precursor solution was kept at 2.5 for all composition of microencapsulated LA. The synthesized microencapsulated LA/SiO2 has been characterized by Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), X-Ray photoelectron spectroscopy (XPS), Scanning electron microscopy (SEM), and Transmission electron microscopy (TEM). The SEM and TEM confirm the microencapsulation of LA with SiO2. Thermogravimetric analysis (TGA) revealed better thermal stability of microencapsulated LA/SiO2 compared to pure LA. PCM with 50% LA i.e. LAPC-6 exhibited the highest encapsulation efficiency (96.50%) and encapsulation ratio (96.15%) through Differential scanning calorimetry (DSC) as well as good thermal reliability even after 30th cycle of heating and cooling process.

scholarly journals Effects of Sintering Temperature on Densification, Microstructure and Mechanical Properties of Al-Based Alloy by High-Velocity Compaction

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 218
Author(s):  
Xianjie Yuan ◽  
Xuanhui Qu ◽  
Haiqing Yin ◽  
Zaiqiang Feng ◽  
Mingqi Tang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Velocity ◽  
Sintered Density ◽  
Sintering Temperature ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
High Velocity Compaction ◽  
Sintered Temperature

This present work investigates the effects of sintering temperature on densification, mechanical properties and microstructure of Al-based alloy pressed by high-velocity compaction. The green samples were heated under the flow of high pure (99.99 wt%) N2. The heating rate was 4 °C/min before 315 °C. For reducing the residual stress, the samples were isothermally held for one h. Then, the specimens were respectively heated at the rate of 10 °C/min to the temperature between 540 °C and 700 °C, held for one h, and then furnace-cooled to the room temperature. Results indicate that when the sintered temperature was 640 °C, both the sintered density and mechanical properties was optimum. Differential Scanning Calorimetry, X-ray diffraction of sintered samples, Scanning Electron Microscopy, Energy Dispersive Spectroscopy, and Transmission Electron Microscope were used to analyse the microstructure and phases.

On the Mechanical Milling of the AlCuFe Icosahedral Phase with Water

2014 ◽  
Vol 793 ◽  
pp. 23-27
Author(s):  
C. Patiño-Carachure ◽  
J. Luis López-Miranda ◽  
F. de la Rosa ◽  
M. Abatal ◽  
R. Pérez ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Milling Time ◽  
Induction Furnace ◽  
Icosahedral Phase ◽  
Quasicrystalline Phase ◽  
X Ray Diffraction ◽  
Cast Sample ◽  
X Ray ◽  
Transmission Electron ◽  
Icosahedral Quasicrystalline

In this investigation the Al64Cu24Fe12 alloy was melted in an induction furnace and solidified under normal casting conditions. The as-cast sample was subject to a heat treatment at 700 oC under argon atmosphere in order to obtain the icosahedral quasicrystalline phase in a monophase region. Subsequently, the icosahedral phase was milled for different times and water added conditions. The pre-alloyed and milled powders were characterized using scanning electron microscopy, X-Ray diffraction, and transmission electron microscopy. The experimental results showed that the icosahedral phase is sensitive to the reaction between water and aluminum of the quasicrystalline alloy to generate hydrogen. As the milling time and the amount of water are increased, the embrittlement reaction of the alloy is accentuated releasing more hydrogen.

Preparation and Property of Al87Ce3Ni8.5Mn1.5 Nanophase Amorphous Composites

2011 ◽  
Vol 412 ◽  
pp. 263-266
Author(s):  
Hong Wei Zhang ◽  
Li Li Zhang ◽  
Feng Rui Zhai ◽  
Jia Jin Tian ◽  
Can Bang Zhang
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Single Phase ◽  
Volume Fraction ◽  
Material Structure ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
Different Temperatures

The higher mechanical strength of Al87Ce3Ni8.5Mn1.5 nanophase amorphous composites has been obtained with two methods. The first nanophase amorphous composites are directly produced by the single roller spin quenching technology. The method taken for the second nanophase amorphous composites is at first to obtain amorphous single-phase alloy, followed by annealed at different temperatures .The formative condition, the microstructure, the particle size, the volume fraction of α-Al phase and microhardness of nanophase amorphous composites etc have been investigated and compared by X-ray diffraction (XRD) and transmission electron microscopy (TEM) and differential scanning calorimetry (DSC). The microstructure of composites produced by the second method is higher than the former, the fabricated material structure of the system is more uniform and the process is easier to control.

Crystallization of Amorphous Si In Al/Si Multilayers

1991 ◽  
Vol 230 ◽  
Author(s):  
Toyohiko J. Konno ◽  
Robert Sinclair
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Layered Structure ◽  
Heat Of Reaction ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
Amorphous Si

AbstractThe crystallization of amorphous Si in a Al/Si multilayer (with a modulation length of about 120Å) was investigated using transmission electron microscopy, differential scanning calorimetry and X-ray diffraction. Amorphous Si was found to crystallize at about 175 °C with the heat of reaction of 11±2(kJ/mol). Al grains grow prior to the nucleation of crystalline Si. The crystalline Si was found to nucleate within the grown Al layers. The incipient crystalline Si initially grows within the Al layer and then spreads through the amorphous Si and other Al layers. Because of extensive intermixing, the original layered structure is destroyed. The Al(111) texture is also enhanced.

Nanoporous Ni and Ni-Cu Fabricated by Dealloying

2009 ◽  
Vol 1228 ◽  
Author(s):  
Masataka Hakamada ◽  
Yasumasa Chino ◽  
Mamoru Mabuchi
Keyword(s):  
Electron Microscopy ◽  
Solid Solution ◽  
Noble Metals ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
The Difference ◽  
20 Nm ◽  
Good Workability ◽  
Scanning Electron

AbstractMetallic nanoporous architecture can be spontaneously attained by dealloying of a binary alloy. The nanoporous architecture can be often fabricated in noble metals such as Au and Pt. In this study, nanoporous Ni, Ni-Cu are fabricated by dealloying rolled Ni-Mn and Cu-Ni-Mn alloys, respectively. Unlike conventional Raney nickel composed of brittle Ni-Al or Cu-Al intermetallic compounds, the initial alloys had good workability probably because of their fcc crystal structures. After the electrolysis of the alloys in (NH4)2SO4 aqueous solution, nanoporous architectures of Ni and Ni-Cu with pore and ligament sizes of 10–20 nm were confirmed by scanning electron microscopy and transmission electron microscopy. X-ray diffraction analyses suggested that Ni and Cu atoms form a homogeneous solid solution in the Ni-Cu nanoporous architecture. The ligament sizes of nanoporous Ni and Ni-Cu were smaller than that of nanoporous Cu, reflecting the difference between diffusivities of Ni and Cu at solid/electrolyte interface. Ni can reduce the pore and ligament sizes of resulting nanoporous architecture when added to initial Cu-Mn alloys.

In situ Transmission Electron Microscopy and Nanoindentation Studies of Phase Transformation and Pseudoelasticity of Shape-memory Titanium-nickel Films

2005 ◽  
Vol 20 (7) ◽  
pp. 1808-1813 ◽  
Author(s):  
X.-G. Ma ◽  
K. Komvopoulos
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Phase Transformation ◽  
Shape Memory ◽  
Heating And Cooling ◽  
Transmission Electron ◽  
Different Temperatures ◽  
Titanium Nickel ◽  
In Situ Heating

Transmission electron microscopy (TEM) and nanoindentation, both with in situ heating capability, and electrical resistivity measurements were used to investigate phase transformation phenomena and thermomechanical behavior of shape-memory titanium-nickel (TiNi) films. The mechanisms responsible for phase transformation in the nearly equiatomic TiNi films were revealed by heating and cooling the samples inside the TEM vacuum chamber. Insight into the deformation behavior of the TiNi films was obtained from the nanoindentation response at different temperatures. A transition from elastic-plastic to pseudoelastic deformation of the martensitic TiNi films was encountered during indentation and heating. In contrast to the traditional belief, the martensitic TiNi films exhibited a pseudoelastic behavior during nanoindentation within a specific temperature range. This unexpected behavior is interpreted in terms of the evolution of martensitic variants and changes in the mobility of the twinned structures in the martensitic TiNi films, observed with the TEM during in situ heating.

Synthesis of (Y,Gd)2O3:Eu nanopowder by a novel co-precipitation processing

2004 ◽  
Vol 19 (12) ◽  
pp. 3586-3591 ◽  
Author(s):  
Jiyang Chen ◽  
Ying Shi ◽  
Jianlin Shi
Keyword(s):  
Electron Microscopy ◽  
Ammonium Hydroxide ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
Hydrogen Carbonate ◽  
Ammonium Hydrogen ◽  
Intense Luminescence ◽  
Co Precipitation

Nano-sized (Y,Gd)2O3:Eu powders were synthesized by a novel co-precipitation processing in which a mixture of ammonium hydroxide and ammonium hydrogen carbonate was adopted as a complex precipitant. Evolution behaviors of precursors during calcinations were studied by means of thermogravimetry-differential scanning calorimetry-mass spectrum, Fourier transform infrared, x-ray diffraction, scanning electron microscopy, and transmission electron microscopy in detail. Nano-sized (Y,Gd)2O3:Eu powder as prepared possessed a primary grain size of about 30 nm and specific surface area of 38 m2/g after being calcined at 850 °C for 2 h, showing much finer grains and less agglomeration. The as prepared nanopowder shows intense luminescence at 611nm under x-ray or ultraviolet excitation. Transparent (Y,Gd)2O3:Eu ceramics can also be fabricated using this high sinterable nanopowder.

Low-temperature instability of Ti2SnC: A combined transmission electron microscopy, differential scanning calorimetry, and x-ray diffraction investigations

2009 ◽  
Vol 24 (1) ◽  
pp. 39-49 ◽  
Author(s):  
J. Zhang ◽  
B. Liu ◽  
J.Y. Wang ◽  
Y.C. Zhou
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Low Temperature ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Temperature Instability ◽  
X Ray ◽  
Transmission Electron ◽  
Ceramic Microstructure

Transmission electron microscopy (TEM), differential scanning calorimetry (DSC), and x-ray diffraction (XRD) investigations were conducted on the hot-pressed Ti2SnC bulk ceramic. Microstructure features of bulk Ti2SnC ceramic were characterized by using TEM, and a needle-shaped β-Sn precipitation was observed inside Ti2SnC grains with the orientation relationship: (0001) Ti2SnC // (200) Sn and Ti2SnC // [001] Sn. With the combination of DSC and XRD analyses, the precipitation of metallic Sn was demonstrated to be a thermal stress-induced process during the cooling procedure. The reheating temperature, even as low as 400 °C, could trigger the precipitation of Sn from Ti2SnC, which indicated the low-temperature instability of Ti2SnC. A substoichiometry Ti2SnxC formed after depletion of Sn from ternary Ti2SnC phase. Under electron beam irradiation, metallic Sn was observed diffusing back into Ti2SnxC. Furthermore, a new Ti7SnC6 phase with the lattice constants of a = 0.32 and c = 4.1 nm was identified and added in the Ti-Sn-C ternary system.

Sign in / Sign up

Export Citation Format

Share Document