scholarly journals Influence of Vacuum Heat Treatments on Microstructure and Mechanical Properties of M35 High Speed Steel

Metals ◽  
2020 ◽  
Vol 10 (5) ◽  
pp. 643
Author(s):  
Chiara Soffritti ◽  
Annalisa Fortini ◽  
Ramona Sola ◽  
Elettra Fabbri ◽  
Mattia Merlin ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Grain Size ◽  
Vickers Hardness ◽  
High Speed ◽  
High Speed Steel ◽  
Plane Strain Fracture Toughness ◽  
Secondary Carbides ◽  
Heat Treated ◽  
Strain Fracture

Towards the end of the last century, vacuum heat treatment of high speed steels was increasingly used in the fabrication of precision cutting tools. This study investigates the influence of vacuum heat treatments at different pressures of quenching gas on the microstructure and mechanical properties of taps made of M35 high speed steel. Taps were characterized by optical microscopy, scanning electron microscopy with energy dispersive spectroscopy, X-ray diffraction, apparent grain size and Vickers hardness measurements, and scratch tests. Failure analysis after tapping tests was also performed to determine the main fracture mechanisms. For all taps, the results showed that microstructures and the values of characteristics of secondary carbides, retained austenite, apparent grain size and Vickers hardness were comparable to previously reported ones for vacuum heat treated high speed steels. For taps vacuum heat treated at six bar, the highest plane strain fracture toughness was due to a higher content of finer small secondary carbides. In contrast, the lowest plane strain fracture toughness of taps vacuum heat treated at eight bar may be due to an excessive amount of finer small secondary carbides, which may provide a preferential path for crack propagation. Finally, the predominant fracture mechanism of taps was quasi-cleavage.

Simultaneous Synthesis and Sintering of Al2O3/Mo2N Composites Using Capsule-Free Nitrogen Hot Isostatic Pressing and their Characterization

2010 ◽  
Vol 62 ◽  
pp. 197-202
Author(s):  
Hirota Ken ◽  
Takaoka Katsuya ◽  
Murase Yasushi ◽  
Kato Masaki
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Grain Size ◽  
Vickers Hardness ◽  
Bending Strength ◽  
Hot Isostatic Pressing ◽  
Isostatic Pressing ◽  
Simultaneous Synthesis ◽  
Powder Compacts ◽  
Al2o3 Matrix

Synthesis of dense materials with the compositions of Al2O3/Mo2N=100/0 ~ 40/60 vol% has been attempted directly from Al2O3/Mo mixed raw powder compacts using capsule-free N2 hot isostatic pressing (HIP). During HIPing [1500°C/(16~20)MPa]/1h], solid/gas reaction between Mo and N2 was introduced to form Mo2N. Most sintered composites consisting of only Al2O3 and Mo2N phases reached a higher relative density than 98.0% with closed pores nevertheless capsule-free HIPing. Distribution of Mo2N particles just formed suppressed the grain growth of Al2O3 during sintering. Mechanical properties, such as bending strength (Σb), Vickers hardness (HV), fracture toughness (K1C), and other properties have been evaluated as a function of their compositions. The best mechanical values of Σb (c.a. 573 MPa), HV (c.a. 20.3 GPa) and K1C (c.a. 5.00 MPa･m1/2) were attained at the composition of Al2O3/Mo2N=90/10 vol%, due to a high density (98.6%) and small grain size of Al2O3 matrix (Gs c.a. 4.70 μm). Further addition of Mo2N reduced the sinterability of matrix grains, resulting in low densities of around 90% at the 40/60 vol% composition.

Fracture toughness relationships in a low-alloy steel

1983 ◽  
Vol 41 ◽  
pp. 224-225
Author(s):  
R. Padmanabhan ◽  
W. E. Wood
Keyword(s):  
Heat Treatment ◽  
Fracture Toughness ◽  
Plane Strain Fracture Toughness ◽  
Low Alloy Steel ◽  
Heat Treated ◽  
Strain Fracture ◽  
Conventional Heat Treatment ◽  
Microstructural Effects ◽  
Improve Fracture Toughness ◽  
Inverse Response

Utilization of high austenitization temperatures to improve fracture toughness of UHSLA steels at similar strength levels has received considerable interest. However, these heat treatments result in reduced ductility and impact toughness. This inverse response of impact and plane strain fracture toughness is essentially due to microstructural effects and it is possible to achieve simultaneous improvements in all these properties through controlled variations in the microstructure.A vacuum remelted Si-modified 4340 steel was chosen for this study under three heat treated conditions, viz., conventional, high temperature and step with austenitization temperatures of 1143 K (1 hr), 1473 K (1 hr) and 1473 K (1 hr) furnace cooled to 1143 K (5 min), respectively. All samples were quenched in oil and tempered at 553 K (1 hr). A modified conventional heat treatment was also designed to achieve a desired microstructure with a 1143 K (1 hr) austenitization, a 923 K (1 hr) intermediate temper (after oil quenching), a 1123 K (3 min) reaustenitization and a final 553 K (1 hr) temper (after requenching) steps.

Effect of (Ni,Mo) and (W,Ti)C on the Microstructure and Mechanical Properties of TiB2 Ceramic Tool Materials

2012 ◽  
Vol 723 ◽  
pp. 233-237 ◽  
Author(s):  
Tong Chun Yang ◽  
Chuan Zhen Huang ◽  
Han Lian Liu ◽  
Bin Zou ◽  
Hong Tao Zhu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Grain Size ◽  
Flexural Strength ◽  
Grain Growth ◽  
Vickers Hardness ◽  
Ceramic Tool ◽  
Tool Materials ◽  
Sintering Additive ◽  
Microstructure And Mechanical Properties

TiB2-(W,Ti)C composites with (Ni,Mo) as sintering additive have been fabricated by hot-pressing technique, and the microstructure and mechanical properties of the composites have been investigated. (Ni,Mo) promotes grain growth of the composites. In the case of 7vol.% (Ni,Mo), the grain size decreases consistently with an increase in the content of (W,Ti)C. When the proper content of (W,Ti)C is added to TiB2 composites, the growth of matrix grains is inhibited and the mechanical properties of the composites are improved. The best mechanical properties of the composites are 1084.13MPa for three-point flexural strength, 7.80MPa•m 1/2 for fracture toughness and 17.92GPa for Vickers hardness.

Densification Behaviour and Mechanical Properties on MgO Doped Zirconia Toughened Alumina (ZTA) Prepared by Two-Stage Sintering

2021 ◽  
Vol 1030 ◽  
pp. 3-10
Author(s):  
Teow Hsien Loong ◽  
Ananthan Soosai ◽  
Suresh Muniandy
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Grain Size ◽  
Total Hip Arthroplasty ◽  
Young’S Modulus ◽  
Vickers Hardness ◽  
Young's Modulus ◽  
Two Stage ◽  
Positive Effect ◽  
Zirconia Toughened Alumina

The effect of doping small amounts of Magnesium Oxide ranging between 0 to 1 vol% on Zirconia Toughened Alumina (ZTA) composites which is one of main biomaterial used for production of total hip arthroplasty were investigated. The samples were produced via conventional two-stage sintering with T1 varies between 1450°C and 1550°C with heating rate of 20°C/min. The samples were then rapid cooled to T2 set at 1400°C with holding time of 12 hours. The microstructural and mechanical properties of the two-stage sintered ZTA are then investigated to determine the feasibility of MgO addition. Combination of two-stage sintering at T1 above 1500 and also small amount of MgO up to 0.5 vol% were shown to have positive effect on ZTA which exhibited improvement on its grain size, mechanical properties such as Vickers hardness, Young’s modulus and fracture toughness compared to undoped ZTA composites. The sample with 0.5 vol% MgO addition sintered at T1 of 1500°C and T2 1400°C was able to achieve Vickers hardness of 19.6 GPa, Young’s modulus of 408 GPa and fracture toughness of 6.8 MPam1/2 without significant grain growth compared to undoped ZTA composites.

Influence of Al2O3 Addition on the Microstructure and Mechanical Properties of Pressureless Sintered Ce-TZP

2005 ◽  
Vol 492-493 ◽  
pp. 783-0 ◽  
Author(s):  
Shui Gen Huang ◽  
Lin Li ◽  
Jef Vleugels ◽  
Pei Ling Wang ◽  
Omer Van der Biest
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Grain Size ◽  
Grain Growth ◽  
Vickers Hardness ◽  
Good Combination ◽  
Al2o3 Content ◽  
Pressureless Sintering ◽  
Sintering Time ◽  
Microstructure And Mechanical Properties

Mixtures of 12 mol% CeO2-stabilised ZrO2 with 5 to 20 wt % Al2O3 were prepared and densified through pressureless sintering in air at 1450° C for 1 to 4 h. The influence of the Al2O3 content and sintering time on the phase constitution, microstructure and mechanical properties of the as-sintered composites were investigated. Fully dense Ce-TZP/Al2O3 ceramics with a good combination of hardness and fracture toughness can be obtained by pressureless sintering in air for only 1 h. The addition of Al2O3 to Ce-TZP improves the mechanical properties and suppresses ZrO2 grain growth. The average ZrO2 grain size increases with increasing sintering time and decreasing Al2O3 content. This leads to an increase in toughness. An excellent fracture toughness of 14.3 MPam1/2 in combination with a Vickers hardness of 9.14 GPa was obtained for 12 mol % CeO2-TZP with 5 wt % Al2O3, sintered for 4 h.

SUPER PANTHER

Alloy Digest ◽  
1963 ◽  
Vol 12 (9) ◽  
Keyword(s):  
Fracture Toughness ◽  
Physical Properties ◽  
High Speed ◽  
High Speed Steel ◽  
Heat Treating ◽  
Heavy Duty ◽  
Cast Irons ◽  
Heat Treated

Abstract Super Panther is a cobalt type high-speed steel recommended for heavy duty cutting of hard, gritty, cast irons and heat treated steels. This datasheet provides information on composition, physical properties, and hardness as well as fracture toughness. It also includes information on forming, heat treating, machining, and joining. Filing Code: TS-137. Producer or source: Allegheny Ludlum Corporation.

Sign in / Sign up

Export Citation Format

Share Document