scholarly journals Amorphous-Nanocrystalline Composites Prepared by High-Pressure Torsion

Metals ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 511 ◽  
Author(s):  
Inga Permyakova ◽  
Alex Glezer
Keyword(s):  
Plastic Deformation ◽  
High Pressure ◽  
Hydrostatic Pressure ◽  
Severe Plastic Deformation ◽  
Amorphous Alloys ◽  
Preparation Method ◽  
High Pressure Torsion ◽  
Structure And Properties ◽  
Nanocrystalline Composites

This article presents systematic studies of the preparation method and the specific features of the changes in the structure and properties of amorphous-nanocrystalline composites formed from melt-quenched ribbons of iron- and cobalt-based amorphous alloys and the Cu-Nb crystalline nanolaminates by severe plastic deformation by torsion in the Bridgeman chamber at high quasi-hydrostatic pressure.

Structure and Properties of Grain Boundaries in Submicrocrystalline W Obtained by Severe Plastic Deformation

2009 ◽  
Vol 283-286 ◽  
pp. 629-638 ◽  
Author(s):  
Vladimir V. Popov ◽  
Ruslan Valiev ◽  
E.N. Popova ◽  
A.V. Sergeev ◽  
A.V. Stolbovsky ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Plastic Deformation ◽  
High Pressure ◽  
Severe Plastic Deformation ◽  
Grain Boundaries ◽  
High Pressure Torsion ◽  
Submicrocrystalline Structure ◽  
Emission Mössbauer Spectroscopy ◽  
Structure And Properties ◽  
Initial State

Submicrocrystalline structure of W obtained by severe plastic deformation (SPD) by high pressure torsion (5 revolutions of anvils at 4000C) and its thermal stability have been examined by TEM. Grain boundaries of submicrocrystalline W have been studied by the method of the emission Mössbauer spectroscopy in the initial state and after annealing at 400-6000С.

Effect of the High Pressure Torsion on Magnetic Properties of Amorphous Alloys

2010 ◽  
Vol 667-669 ◽  
pp. 1077-1082
Author(s):  
Alex M. Glezer ◽  
Margarita R. Plotnikova ◽  
Sergey V. Dobatkin ◽  
Nikolai S. Perov ◽  
Anna V. Shalimova
Keyword(s):  
Plastic Deformation ◽  
High Pressure ◽  
Magnetic Properties ◽  
Severe Plastic Deformation ◽  
Saturation Magnetization ◽  
Amorphous Alloys ◽  
Amorphous Matrix ◽  
High Pressure Torsion ◽  
Melt Quenching

The effect of severe plastic deformation in Bridgman’s chamber on magnetic properties of the amorphous alloys of metal-metalloid type Ni44Fe29Co15Si2B10, Fe50Ni33B17, Fe70Cr15B15 obtained by the melt quenching was studied. The substantial alteration of saturation magnetization depending on the number of ferromagnetic and antiferromagnetic components in the alloy was revealed. It was supposed that the internal separation into nanoscaled areas enriched and depleted by ferromagnetic components took place in the amorphous matrix under the action of severe plastic deformation.

scholarly journals The Effect of the In-Situ Heat Treatment on the Martensitic Transformation and Specific Properties of the Fe-Mn-Si-Cr Shape Memory Alloys Processed by HSHPT Severe Plastic Deformation

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4621
Author(s):  
Carmela Gurau ◽  
Gheorghe Gurau ◽  
Felicia Tolea ◽  
Bogdan Popescu ◽  
Mihaela Banu ◽  
...  
Keyword(s):  
Plastic Deformation ◽  
High Pressure ◽  
Severe Plastic Deformation ◽  
High Speed ◽  
High Pressure Torsion ◽  
Electron Interaction ◽  
Sudden Increase ◽  
Neel Temperature ◽  
Néel Temperature

This work focuses on the temperature evolution of the martensitic phase ε (hexagonal close packed) induced by the severe plastic deformation via High Speed High Pressure Torsion method in Fe57Mn27Si11Cr5 (at %) alloy. The iron rich alloy crystalline structure, magnetic and transport properties were investigated on samples subjected to room temperature High Speed High Pressure Torsion incorporating 1.86 degree of deformation and also hot-compression. Thermo-resistivity as well as thermomagnetic measurements indicate an antiferromagnetic behavior with the Néel temperature (TN) around 244 K, directly related to the austenitic γ-phase. The sudden increase of the resistivity on cooling below the Néel temperature can be explained by an increased phonon-electron interaction. In-situ magnetic and electric transport measurements up to 900 K are equivalent to thermal treatments and lead to the appearance of the bcc-ferrite-like type phase, to the detriment of the ε(hcp) martensite and the γ (fcc) austenite phases.

Reversible Martensitic Transformation Produced by Severe Plastic Deformation of Metastable Austenitic Steel

2013 ◽  
Vol 738-739 ◽  
pp. 491-495 ◽  
Author(s):  
Igor Litovchenko ◽  
Alexander Tyumentsev ◽  
Alexander V. Korznikov
Keyword(s):  
Plastic Deformation ◽  
High Pressure ◽  
Martensitic Transformation ◽  
Severe Plastic Deformation ◽  
Dynamic Recrystallization ◽  
Austenitic Steel ◽  
High Pressure Torsion ◽  
Martensitic Transformations ◽  
Metastable Austenitic Steel ◽  
Nanostructured States

The peculiarities of martensitic transformations and formation of nanostructured states in metastable austenitic steel (Fe-18Cr-8Ni-Ti) after severe plastic deformation by high pressure torsion are investigated. It is shown that during severe plastic deformation with increased strain rate not only direct (γ→α΄) but also reverse (α΄→γ) martensitic transformations occur, which is revealed by the changes in the volume content of α΄ - martensite during deformation. The fragments thought to be formed by direct and reverse martensitic transformations and those of dynamic recrystallization of austenite are observed.

Mechanism of activation of TiFe intermetallics for hydrogen storage by severe plastic deformation using high-pressure torsion

2013 ◽  
Vol 103 (14) ◽  
pp. 143902 ◽  
Author(s):  
Kaveh Edalati ◽  
Junko Matsuda ◽  
Makoto Arita ◽  
Takeshi Daio ◽  
Etsuo Akiba ◽  
...  
Keyword(s):  
Plastic Deformation ◽  
High Pressure ◽  
Severe Plastic Deformation ◽  
Hydrogen Storage ◽  
High Pressure Torsion

Processing of Aluminium Alloys by Severe Plastic Deformation

2006 ◽  
Vol 519-521 ◽  
pp. 45-54 ◽  
Author(s):  
Terence G. Langdon
Keyword(s):  
Plastic Deformation ◽  
High Pressure ◽  
Severe Plastic Deformation ◽  
Elevated Temperatures ◽  
High Pressure Torsion ◽  
Simple Procedure ◽  
Superplastic Forming ◽  
High Strength ◽  
Ultrafine Grain ◽  
Grain Sizes

Processing through the application of severe plastic deformation (SPD) has become important over the last decade because it is now recognized that it provides a simple procedure for producing fully-dense bulk metals with grain sizes lying typically in the submicrometer range. There are two major procedures for SPD processing. First, equal-channel angular pressing (ECAP) refers to the repetitive pressing of a metal bar or rod through a die where the sample is constrained within a channel bent through an abrupt angle at, or close to, 90 degrees. Second, high-pressure torsion (HPT) refers to the procedure in which the sample, generally in the form of a thin disk, is subjected to a very high pressure and concurrent torsional straining. Both of these processes are capable of producing metallic alloys with ultrafine grain sizes and with a reasonable degree of homogeneity. Furthermore, the samples produced in this way may exhibit exceptional mechanical properties including high strength at ambient temperature through the Hall-Petch relationship and a potential superplastic forming capability at elevated temperatures. This paper reviews these two procedures and gives examples of the properties of aluminum alloys after SPD processing.

scholarly journals Influence of special features of the gradient structure formation during severe plastic deformation of alloys with different types of a crystalline lattice

2019 ◽  
Vol 17 (1) ◽  
pp. 64-75 ◽  
Author(s):  
Georgy I. Raab ◽  
Ilyas S. Kodirov ◽  
Gennady N. Aleshin ◽  
Arseniy G. Raab ◽  
Nikolai K. Tsenev
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
High Pressure ◽  
Severe Plastic Deformation ◽  
Structure Formation ◽  
High Pressure Torsion ◽  
Crystalline Lattice ◽  
Gradient Structure ◽  
Temperature Range ◽  
Deformation Treatment

Problem Statement (Relevance): The paper describes some features and prospective benefits of deformation by methods of drawing with shear (SD) and high pressure torsion (HPT) in a temperature range of dynamic strain aging (DSA) effect, which allow receiving a high complex of physical and mechanical properties. Objectives: The study aims to investigate and analyze features of the structure formation with the combined application of severe plastic deformation (SPD) and the DSA effect during deformation by drawing with shear and high pressure torsion, to establish patterns of the gradient structure formation. Methods Applied: 1. Computer simulation in Deform 3D software to investigate the stress-strain state on materials with various types of a crystalline lattice: copper grade M1 (FCC), Steel 10 (BCC) and titanium VT1-0 (HCP) and a further comparison with experimental results. 2. Microhardness measurement 3. Scanning and transmission electron microscopy. Originality: This research resulted in investigation of the combined effect of the DSA effect and SPD on the gradient structure formation and mechanical properties of metals with various crystalline lattices. Findings: the paper presents the results of the study of the structure formation during non-monotonous plastic deformation of the alloys (steel 10, copper and titanium) with various crystalline lattice types by SD, as well as ECAP and HPT of low-carbon steel in the temperature range of the DSA effect. Deformation mechanisms and features of the deformation behavior on a mesoscopic scale under various deformation treatment modes are analyzed. The temperature range of the DSA effect in steel 10 under ECAP and the fact of the gradient structure formation under HPT are established. Practical Relevance: The study helped to obtain data that can be used to choose the optimal deformation treatment mode with the DSA effect.

Sign in / Sign up

Export Citation Format

Share Document