scholarly journals High-Speed Rotary Ultrasonic Elliptical Milling of Ti-6Al-4V Using High-Pressure Coolant

Metals ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 500
Author(s):  
Mingliang Zhang ◽  
Deyuan Zhang ◽  
Hailin Guo ◽  
Ze Gao ◽  
Daxi Geng ◽  
...  
Keyword(s):  
High Pressure ◽  
Ultrasonic Vibration ◽  
High Speed ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Wear Mode ◽  
Cooling Mechanism ◽  
Cooling And Lubrication ◽  
Ultrasonic Vibration Cutting ◽  
High Pressure Coolant

High-speed rotary ultrasonic elliptical milling (HRUEM), as a novel ultrasonic vibration cutting method, has been introduced in milling the alloy Ti-6Al-4V. The application of ultrasonic vibration in high-speed milling can help open the cutting contact area intermittently. New cutting effects will happen with full use of the separation effect brought by ultrasonic vibration and the cooling effect brought by a high-pressure coolant (HPC). On the basis of that, this paper firstly introduces HPC into HRUEM of Ti-6Al-4V in the open literature and analyzes the tool-workpiece separation cooling mechanism in HRUEM, including kinematic analysis of tool tip trajectories, tool-workpiece separation principles and high-pressure coolant effects. We have conducted a comprehensive experimental study and the results show when HPC is increased to 200 bar, compared to conventional milling (CM), the tool life in HUREM can be extended by 6.6 times at 80 m/min, 4.2 times at 120 m/min and 2.4 times at 160 m/min. The maximum material removal volume (MRV) for a given new end mill in HRUEM is increased by 657% approximately. When the cutting speed is 80 m/min, the cutting temperature of the workpiece in HRUEM is reduced by 24.1% compared to that of CM. By applying the combination of HPC and tool-workpiece periodic separation, we can significantly enhance the cooling and lubrication efficiency in HRUEM and also inhibit the tool wear mode of adhesive wear typically occurred in CM.

scholarly journals EFFECT OF HIGH PRESSURE COOLANT JET ON CUTTING TEMPERATURE, TOOL WEAR AND SURFACE FINISH IN TURNING HARDENED (HRC 48) STEEL

2015 ◽  
Vol 45 (1) ◽  
pp. 1-6 ◽  
Author(s):  
Mozammel Mia ◽  
Nikhil Ranjan Dhar
Keyword(s):  
High Pressure ◽  
Tool Wear ◽  
Cutting Forces ◽  
High Speed ◽  
Hard Turning ◽  
Cutting Tools ◽  
Cutting Temperature ◽  
Beneficial Effects ◽  
Coated Carbide ◽  
High Pressure Coolant

Hard turning of harder material differs from conventional turning because of its larger specific cutting forces requirements. The beneficial effects of hard turning can be offset by excessive temperature generation which causes rapid tool wear or premature tool failure if the brittle cutting tools required for hard turning are not used properly. Under these considerations, the concept of high-pressure coolant (HPC) presents itself as a possible solution for high speed machining in achieving slow tool wear while maintaining cutting forces at reasonable levels, if the high pressure cooling parameters can be strategically tuned. This paper deals with an experimental investigation of some aspects of the turning process applied on hardened steel (HRC48) using coated carbide tool under high-pressure coolant, comparing it with dry cut. The results indicate that the use of high-pressure coolant leads to reduced surface roughness, delayed tool flank wear, and lower cutting temperature, while also having a minimal effect on the cutting forces.

Cutting Temperature and Cutting Forces Investigation Based on the Taguchi Design Method when High-Speed Milling of Titanium Matrix Composites with PCD Tool

2016 ◽  
Vol 836-837 ◽  
pp. 168-174 ◽  
Author(s):  
Ying Fei Ge ◽  
Hai Xiang Huan ◽  
Jiu Hua Xu
Keyword(s):  
Cutting Force ◽  
Feed Rate ◽  
Cutting Forces ◽  
High Speed ◽  
Volume Fraction ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth

High-speed milling tests were performed on vol. (5%-8%) TiCp/TC4 composite in the speed range of 50-250 m/min using PCD tools to nvestigate the cutting temperature and the cutting forces. The results showed that radial depth of cut and cutting speed were the two significant influences that affected the cutting forces based on the Taguchi prediction. Increasing radial depth of cut and feed rate will increase the cutting force while increasing cutting speed will decrease the cutting force. Cutting force increased less than 5% when the reinforcement volume fraction in the composites increased from 0% to 8%. Radial depth of cut was the only significant influence factor on the cutting temperature. Cutting temperature increased with the increasing radial depth of cut, feed rate or cutting speed. The cutting temperature for the titanium composites was 40-90 °C higher than that for the TC4 matrix. However, the cutting temperature decreased by 4% when the reinforcement's volume fraction increased from 5% to 8%.

High-Speed Capturing of Stress Distribution of Workpiece under Ultrasonically Assisted Cutting Condition

2014 ◽  
Vol 1017 ◽  
pp. 747-752
Author(s):  
Hiromi Isobe ◽  
Keisuke Hara
Keyword(s):  
Stress Distribution ◽  
Cutting Force ◽  
High Speed ◽  
Cutting Tool ◽  
Light Emission ◽  
Cutting Speed ◽  
Cutting Condition ◽  
Photoelastic Method ◽  
Intermittent Cutting ◽  
Ultrasonic Vibration Cutting

This paper reports the stress distribution inside the workpiece under ultrasonic vibration cutting (UVC) condition. Many researchers have reported the improvement of tool wear, burr generation and surface integrity by reduction of time-averaged cutting force under UVC condition. However general dynamometers have an insufficient frequency band to observe the processing phenomena caused by UVC. In this paper, stress distribution inside the workpiece during UVC was observed by combining the flash light emission synchronized with ultrasonically vibrating cutting tool and the photoelastic method. Instantaneous stress distribution during UVC condition was observed. Because UVC induced an intermittent cutting condition, the stress distribution changed periodically and disappeared when the tool leaved from the workpiece. It was found that instantaneous maximum cutting force during UVC condition was smaller than quasi-static cutting force during conventional cutting when the cutting speed was less than 500 mm/min.

Development of Cutting Tools With Micro-Textured Surface for High Speed Machining of Ti-6Al-4V

2021 ◽  
Author(s):  
Mitsuru Hasegawa ◽  
Tatsuya Sugihara
Keyword(s):  
Tool Life ◽  
High Speed ◽  
Metal Cutting ◽  
Failure Process ◽  
Cutting Tools ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Fluid ◽  
Textured Surface ◽  
Textured Surfaces

Abstract In cutting of Ti-6Al-4V alloy, the cutting speed is limited since a high cutting temperature leads to severe tool wear and short tool life, resulting in poor production efficiency. On the other hand, some recent literature has reported that various beneficial effects can be provided by forming micro-textures on the tool surface in the metal cutting process. In this study, in order to achieve high-performance machining of Ti-6Al-4V, we first investigated the mechanism of the tool failure process for a cemented carbide cutting tool in high-speed turning of Ti-6Al-4V. Based on the results, cutting tools with micro textured surfaces were developed under the consideration of a cutting fluid action. A series of experiments showed that the textured rake face successfully decreases the cutting temperature, resulting in a significant suppression of both crater wear and flank wear. In addition, the temperature zone where the texture tool is effective in terms of the tool life in the Ti-6Al-4V cutting was discussed.

scholarly journals Cutting Performance Evaluation of the Coated Tools in High-Speed Milling of AISI 4340 Steel

Materials ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3266 ◽  
Author(s):  
Yuan Li ◽  
Guangming Zheng ◽  
Xiang Cheng ◽  
Xianhai Yang ◽  
Rufeng Xu ◽  
...  
Keyword(s):  
Performance Evaluation ◽  
Cutting Force ◽  
High Speed ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Performance ◽  
High Speed Milling ◽  
Coated Tools ◽  
Coated Tool ◽  
Aisi 4340

The cutting performance of cutting tools in high-speed machining (HSM) is an important factor restricting the machined surface integrity of the workpiece. The HSM of AISI 4340 is carried out by using coated tools with TiN/TiCN/TiAlN multi-coating, TiAlN + TiN coating, TiCN + NbC coating, and AlTiN coating, respectively. The cutting performance evaluation of the coated tools is revealed by the chip morphology, cutting force, cutting temperature, and tool wear. The results show that the serration and shear slip of the chips become more clear with the cutting speed. The lower cutting force and cutting temperature are achieved by the TiN/TiCN/TiAlN multi-coated tool. The flank wear was the dominant wear form in the milling process of AISI 4340. The dominant wear mechanisms of the coated tools include the crater wear, coating chipping, adhesion, abrasion, and diffusion. In general, a TiN/TiCN/TiAlN multi-coated tool is the most suitable tool for high-speed milling of AISI 4340, due to the lower cutting force, the lower cutting temperature, and the high resistance of the element diffusion.

Observations of Tool Life and Wear Mechanisms in High Speed Machining of Ti-6Al-4V With PCD Tools Using High Pressure Coolant Supply

2005 ◽  
Author(s):  
E. O. Ezugwu ◽  
J. Bonney ◽  
W. F. Sales ◽  
R. B. da Silva
Keyword(s):  
High Pressure ◽  
Titanium Alloy ◽  
Tool Life ◽  
Wear Mechanisms ◽  
High Speed ◽  
Cutting Tool ◽  
High Speed Machining ◽  
The Past ◽  
Pcd Tools ◽  
High Pressure Coolant

Usage of titanium alloys has increased since the past 50 years despite difficulties encountered during machining. In this study PCD tools were evaluated when machining Ti-6Al-4V alloy at high speed conditions under high pressure coolant supplies. Increase in coolant pressure tend to improve tool life and minimise adhesion of the work material on the cutting tool during machining. Adhesion can be accelerated by the susceptibility of titanium alloy to galling during machining.

Sign in / Sign up

Export Citation Format

Share Document