scholarly journals Effect of Friction Stir Processing on Microstructural, Mechanical, and Corrosion Properties of Al-Si12 Additive Manufactured Components

Metals ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 85 ◽  
Author(s):  
Ghazal Moeini ◽  
Seyed Vahid Sajadifar ◽  
Tom Engler ◽  
Ben Heider ◽  
Thomas Niendorf ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Corrosion Behavior ◽  
Friction Stir Processing ◽  
Micro Hardness ◽  
Corrosion Properties ◽  
Microstructural Investigation ◽  
Friction Stir ◽  
Size Refinement ◽  
Hardness Values

Additive manufacturing (AM) is an advanced manufacturing process that provides the opportunity to build geometrically complex and highly individualized lightweight structures. Despite its many advantages, additively manufactured components suffer from poor surface quality. To locally improve the surface quality and homogenize the microstructure, friction stir processing (FSP) technique was applied on Al-Si12 components produced by selective laser melting (SLM) using two different working media. The effect of FSP on the microstructural evolution, mechanical properties, and corrosion resistance of SLM samples was investigated. Microstructural investigation showed a considerable grain refinement in the friction stirred area, which is due to the severe plastic deformation and dynamic recrystallization of the material in the stir zone. Micro-hardness measurements revealed that the micro-hardness values of samples treated using FSP are much lower compared to SLM components in the as-built condition. This reduction of hardness values in samples treated with FSP can be explained by the dissolution of the very fine Si-phase network, being characteristic for SLM samples, during FSP. Surface topography also demonstrated that the FSP results in the reduction of surface roughness and increases the homogeneity of the SLM microstructure. Decreased surface roughness and grain size refinement in combination with the dissolved Si-phase network of the FSP treated material result in considerable changes in corrosion behavior. This work addresses the corrosion properties of surface treated additive manufactured Al-Si12 by establishing adequate microstructure-property relationships. The corrosion behavior of SLM-manufactured Al-Si12 alloys is shown to be improved by FSP-modification of the surfaces.

scholarly journals Effect of Friction Stir Processing at High Rotational Speed on Aging of a HPDC Mg9Al1Zn

Metals ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 1014
Author(s):  
Emanuela Cerri ◽  
Emanuele Ghio
Keyword(s):  
Friction Stir Processing ◽  
Preliminary Investigation ◽  
Dynamic Precipitation ◽  
High Rotational Speed ◽  
Friction Stir ◽  
Final Aging ◽  
Different Temperatures ◽  
Hardness Increase ◽  
Pressure Die Casting ◽  
Hardness Values

Friction stir processing (FSP) has confirmed its valuable contribution to refining microstructures and the improvement of mechanical properties for Mg-Al alloys. Reference papers illustrate that post-processing aging treatments enhance hardness, but with the application of a solution heat treatment prior to FSP. In this work, aging was performed at two different temperatures (170 and 300 °C) directly on friction stir processed samples of AZ91 produced using high pressure die casting (HPDC). High rotational speeds of the tools (2500 and 3000 rpm) increases the heat input and the temperature of the plates during the process up to 270 °C. Vickers microhardness (HV) increased by 15–20% in the nugget, compared to the as FSPed condition; moreover, a greater homogeneity of hardness values was found at the higher aging temperature used. The β-Mg17Al12 precipitates are randomly distributed inside grains of the stirred area, while in the thermomechanical affected zone (TMAZ) they have grown in a network similar to the old eutectic. A preliminary investigation of FSPed samples deformed at 300 °C found that an equivalent hardness increase is achievable using hot deformation due to dynamic precipitation; to find local homogeneity in hardness, it is worth performing a final aging.

EFFECT OF FRICTION STIR PROCESSING ON CORROSION BEHAVIOR OF CAST AZ91C MAGNESIUM ALLOY

2019 ◽  
Vol 26 (06) ◽  
pp. 1850213 ◽  
Author(s):  
BEHZAD HASSANI ◽  
RUDOLF VALLANT ◽  
FATHALLAH KARIMZADEH ◽  
MOHAMMAD HOSSEIN ENAYATI ◽  
SOHEIL SABOONI ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Corrosion Resistance ◽  
Magnesium Alloy ◽  
Corrosion Behavior ◽  
Friction Stir Processing ◽  
Potentiodynamic Polarization ◽  
Passive Layer ◽  
Friction Stir ◽  
T6 Heat Treatment ◽  
Az91c Magnesium Alloy

The corrosion behavior of as-cast AZ91C magnesium alloy was studied by performing friction stir processing (FSP) and FSP followed by solution annealing and then aging. Phase analysis, microstructural characterization, potentiodynamic polarization test and immersion tests were carried out to relate the corrosion behavior to the samples microstructure. The microstructural observations revealed the breakage and dissolution of coarse dendritic microstructure as well as the coarse secondary [Formula: see text]-Mg[Formula: see text]Al[Formula: see text] phase which resulted in a homogenized and fine grained microstructure (15[Formula: see text][Formula: see text]m). T6 heat treatment resulted in an excessive growth and dispersion of the secondary phases in the microstructure of FSP zone. The potentiodynamic polarization and immersion tests proved a significant effect of both FSP and FSP followed by T6 on increasing the corrosion resistance of the cast AZ91C magnesium alloy. Improve in corrosion resistance after FSP was attributed to grain refinement and elimination of segregations and casting defects which makes more adhesive passive layer. Increase in volume fraction of precipitations after T6 heat treatment is determined to be the main factor which stabilizes the passive layer at different polarization values and is considered to be responsible for increasing the corrosion resistance.

scholarly journals Friction Stir Processing of the Magnesium Alloy AZ61: Grain Size Refinement and Mechanical Properties

2012 ◽  
Vol 706-709 ◽  
pp. 1823-1828 ◽  
Author(s):  
J.A. del Valle ◽  
P. Rey ◽  
D. Gesto ◽  
D. Verdera ◽  
Oscar A. Ruano
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Magnesium Alloy ◽  
Friction Stir Processing ◽  
Superplastic Forming ◽  
Important Change ◽  
Heat Extraction ◽  
Processing Temperature ◽  
Friction Stir ◽  
Size Refinement

The effect of friction stir processing (FSP), on the microstructure and mechanical properties of a magnesium alloy AZ61 has been analyzed. This is a widely used wrought magnesium alloy provided in the form of rolled and annealed sheets with a grain size of 45 μm. The FSP was performed with an adequate cooling device in order to increase the heat extraction and reduce the processing temperature. The final microstructure showed a noticeable grain size refinement down to values close to 1.8 μm and an important change in texture. The change in texture favors basal slip during tensile testing leading to an increase of ductility and a decrease in yield stress. The stability of the grain size and the creep behavior at high temperatures were investigated. The optimum conditions for superplastic forming were determined; however, the presence of a large amount of cavities precludes the achievement of high superplastic elongations. Additionally, these results are compared with those obtained by severe hot rolling.

Corrosion Behavior of a Mg Alloy AE42 Subjected to Friction Stir Processing

CORROSION ◽  
10.5006/0750 ◽  
2013 ◽  
Vol 69 (2) ◽  
pp. 122-135 ◽  
Author(s):  
H.S. Arora ◽  
H. Singh ◽  
B.K. Dhindaw
Keyword(s):  
Corrosion Behavior ◽  
Friction Stir Processing ◽  
Mg Alloy ◽  
Friction Stir

Microstructures and Properties of Biological Mg-Zn-Y-Nd Alloy by Friction Stir Processing

2013 ◽  
Vol 745-746 ◽  
pp. 33-38 ◽  
Author(s):  
Shi Jie Zhu ◽  
Li Guo Wang ◽  
Jin Jin ◽  
Jing Wang ◽  
Yu Feng Sun ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Processing ◽  
Cast Alloy ◽  
Corrosion Current ◽  
Stir Zone ◽  
Grain Structure ◽  
Second Phase ◽  
Uniform Corrosion ◽  
Corrosion Properties ◽  
Friction Stir

In order to improve the mechanical properties and processing performance of the Mg alloys, and to prevent magnesium alloy from non-uniform corrosion and too fast degradation in the degradation process, the biological medical Mg-Zn-Y-Nd alloy was modified by the friction stir processing (FSP) technique in this paper. The microstructural evolution and phase constitute of the stir zone of Mg-Zn-Y-Nd alloy were investigated, the microhardness and the corrosion properties of the alloy after FSP process was studied. The results showed that the FSP parameters had significant influence on the stir zone and thermo-mechanically affected zone. The stir zone experienced severe plastic deformation and complete dynamic recrystallization after FSP. The stir zone consists of fine equiaxed recystallized grains, and thermo-mechanically affected zone (TMAZ) has deformed grain structure. The second phase distributed along grain boundaries in as-cast state was broken during the FSP and transformed into fine, uniform and dispersed particles in the grains. After FSP, the size of grains was reduced from 50μm (as-cast alloy) to 1-2μm. However, the second phase constitution didnt change. The alloy obtained good comprehensive mechanical properties after FSP. The microhardness of alloy after FSP increased from 39HV (as-cast alloy) to 64HV(FSPed alloy). The results of electrochemical tests in simulated body fluid showed that the corrosion potential of FSP alloy increased and corrosion current density decreased, which confirmed the uniform corrosion of FSPed alloy.

Sign in / Sign up

Export Citation Format

Share Document