scholarly journals Influence of Welding Speed on Microstructure and Mechanical Properties of 5251 Aluminum Alloy Joints Fabricated by Self-Reacting Friction Stir Welding

Materials ◽  
2021 ◽  
Vol 14 (20) ◽  
pp. 6178
Author(s):  
Shikang Gao ◽  
Li Zhou ◽  
Guangda Sun ◽  
Huihui Zhao ◽  
Xiaolong Chu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Aluminum Alloy ◽  
Welding Speed ◽  
Fracture Characteristics ◽  
Void Defect ◽  
Friction Stir ◽  
Microhardness Distribution ◽  
Microstructure And Mechanical Properties ◽  
Quality Surface

In the present study, 8 mm-thick 5251 aluminum alloy was self-reacting friction stir welded (SRFSW) employing an optimized friction stir tool to analyze the effect of welding speed from 150 to 450 mm/min on the microstructure and mechanical properties at a constant rotation speed of 400 rpm. The results indicated that high-quality surface finish and defect-free joints were successfully obtained under suitable process parameters. The microhardness distribution profiles on the transverse section of joint exhibited a typical “W” pattern. The lowest hardness values located at the heat-affected zone (HAZ) and the width of the softened region decreased with increasing welding speed. The tensile strength significantly decreased due to the void defect, which showed mixed fracture characteristics induced by the decreasing welding speed. The average tensile strength and elongation achieved by the SRFSW process were 242.61 MPa and 8.3% with optimal welding conditions, and the fracture surface exhibited a typical toughness fracture mode.

Study on the Microstructure and Mechanical Properties of Welding Joints of 7A05 Aluminum Alloy by FSW

2014 ◽  
Vol 496-500 ◽  
pp. 110-113
Author(s):  
Dong Gao Chen ◽  
Jin He Liu ◽  
Zhi Hua Ma ◽  
Wu Lin Yang
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Welding Speed ◽  
Welded Joint ◽  
Optical Microscope ◽  
Nugget Zone ◽  
Friction Stir ◽  
Microstructure And Mechanical Properties ◽  
Welding Joints

The7A05 aluminum alloy of the 10mm thickness was welded by the friction stir welding. The microstructure and mechanical Properties of the welded joint was researched by the optical microscope, etc. The results showed: the microstructure of the weld nugget zone and the thermal mechanically affected zone were refined as the welding speed increasing when the rotate speed is constant. As the welding speed increasing the strength of extension of the welded joint is increasing at first and then stable basically. but the yield strength had no obvious change.

scholarly journals Metallurgical and Mechanical Characterization of High-Speed Friction Stir Welded AA 6082-T6 Aluminum Alloy

Materials ◽  
2019 ◽  
Vol 12 (24) ◽  
pp. 4211 ◽  
Author(s):  
Anton Naumov ◽  
Iuliia Morozova ◽  
Evgenii Rylkov ◽  
Aleksei Obrosov ◽  
Fedor Isupov ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Welding Speed ◽  
Welded Joints ◽  
High Speed ◽  
Structural Characteristics ◽  
Tensile Fracture ◽  
Friction Stir ◽  
Microhardness Distribution ◽  
Aluminum Sheets

The objective of this study was to investigate the effect of the high welding speed on the mechanical properties and their relations to microstructural characteristics of butt friction stir welded joints with the use of 6082-T6 aluminum alloy. The aluminum sheets of 2.0 mm thick were friction stir welded at low (conventional FSW) and high welding speeds (HSFSW) of 200 and 2500 mm/min, respectively. The grain size in the nugget zone (NZ) was decreased; the width of the softened region was narrowed down as well as the lowest microhardness value located in the heat-affected zone (HAZ) was enhanced by HSFSW. The increasing welding speed resulted in the higher ultimate tensile strength and lower elongation, but it had a slight influence on the yield strength. The differences in mechanical properties were explained by analysis of microstructural changes and tensile fracture surfaces of the welded joints, supported by the results of the numerical simulation of the temperature distribution and material flow. The fracture of the conventional FSW joint occurred in the HAZ, the weakest weld region, while all HSFSW joints raptured in the NZ. This demonstrated that both structural characteristics and microhardness distribution influenced the actual fracture locations.

Sign in / Sign up

Export Citation Format

Share Document