scholarly journals Influence of Infill Pattern on the Elastic Mechanical Properties of Fused Filament Fabrication (FFF) Parts through Experimental Tests and Numerical Analyses

Materials ◽  
2021 ◽  
Vol 14 (18) ◽  
pp. 5459
Author(s):  
Jordi Bonada ◽  
Mª Magdalena Pastor ◽  
Irene Buj-Corral
Keyword(s):  
Mechanical Properties ◽  
Manufacturing Process ◽  
Experimental Tests ◽  
Tensile Tests ◽  
Numerical Analyses ◽  
Layer By Layer ◽  
Fused Filament Fabrication ◽  
Element Analysis ◽  
Young’S Moduli ◽  
Printing Parameters

Fused Filament Fabrication (FFF) is one of the most extensive additive manufacturing technologies for printing prototypes or final parts in various fields. Some printed parts need to meet structural requirements to be functional parts. Therefore, it is necessary to know the mechanical behavior of the printed samples as a function of the printing parameters in order to optimize the material used during the manufacturing process. It is known that FFF parts can present orthotropic characteristics as a consequence of the manufacturing process, in which the material is deposited layer by layer. Therefore, these characteristics must be considered for a correct evaluation of the printed parts from a structural point of view. In this paper, the influence of the type of filling pattern on the main mechanical properties of the printed parts is analyzed. For this purpose, the first parts are 3D printed using three different infill patterns, namely grid, linear with a raster orientation of 0 and 90°, and linear with a raster orientation of 45°. Then, experimental tensile tests, on the one hand, and numerical analyses using finite elements, on the other hand, are carried out. The elastic constants of the material are obtained from the experimental tests. From the finite element analysis, using a simple approach to create a Representative Volume Model (RVE), the constitutive characteristics of the material are estimated: Young’s Moduli and Poisson’s ratios of the printed FFF parts. These values are successfully compared with those of the experimental tests. The results clearly show differences in the mechanical properties of the FFF printed parts, depending on the internal arrangement of the infill pattern, even if similar 3D printing parameters are used.

scholarly journals Deterioration of the Mechanical Properties of FFF 3D-Printed PLA Structures

Inventions ◽  
2020 ◽  
Vol 6 (1) ◽  
pp. 1
Author(s):  
Asahi Yonezawa ◽  
Akira Yamada
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Test Piece ◽  
Tensile Tests ◽  
Poly Lactic Acid ◽  
Uniaxial Tensile ◽  
Layer By Layer ◽  
Fused Filament Fabrication ◽  
Test Pieces ◽  
3D Printed

Poly(lactic acid) (PLA) is a biodegradable polymer material used for the fabrication of objects by fused filament fabrication (FFF) 3D printing. FFF 3D printing technology has been quickly spreading over the past few years. An FFF-3D-printed object is formed from melted polymer extruded from a nozzle layer-by-layer. The mechanical properties of the object, and the changes in those properties as the object degrades, differ from the properties and changes observed in bulk objects. In this study we evaluated FFF-3D-printed objects by uniaxial tensile tests and four-point flexural tests to characterize the changes of three mechanical properties, namely, the maximum stress, elastic modulus, and breaking energy. Eight types of test pieces printed directly by an FFF 3D printer using two scan patterns and two interior fill percentages (IFPs) were tested by the aforesaid methods. The test pieces were immersed in saline and kept in an incubator at 37 °C for 30, 60, or 90 days before the mechanical testing. The changes in the mechanical properties differed largely between the test piece types. In some of the test pieces, transient increases in strength were observed before the immersion degraded the strength. Several of the test piece types were found to have superior specific strength in the tests. The results obtained in this research will be helpful for the design of PLA structures fabricated by FFF 3D printing.

scholarly journals Metallization of Thermoplastic Polymers and Composites 3D Printed by Fused Filament Fabrication

Technologies ◽  
2021 ◽  
Vol 9 (3) ◽  
pp. 49
Author(s):  
Alessia Romani ◽  
Andrea Mantelli ◽  
Paolo Tralli ◽  
Stefano Turri ◽  
Marinella Levi ◽  
...  
Keyword(s):  
Physical Vapor Deposition ◽  
Test Sample ◽  
Tensile Tests ◽  
Layer By Layer ◽  
Post Processing ◽  
Thermoplastic Polymers ◽  
Fused Filament Fabrication ◽  
Scanning Calorimetry ◽  
3D Printed ◽  
Manufacturing Technologies

Fused filament fabrication allows the direct manufacturing of customized and complex products although the layer-by-layer appearance of this process strongly affects the surface quality of the final parts. In recent years, an increasing number of post-processing treatments has been developed for the most used materials. Contrarily to other additive manufacturing technologies, metallization is not a common surface treatment for this process despite the increasing range of high-performing 3D printable materials. The objective of this work is to explore the use of physical vapor deposition sputtering for the chromium metallization of thermoplastic polymers and composites obtained by fused filament fabrication. The thermal and mechanical properties of five materials were firstly evaluated by means of differential scanning calorimetry and tensile tests. Meanwhile, a specific finishing torture test sample was designed and 3D printed to perform the metallization process and evaluate the finishing on different geometrical features. Furthermore, the roughness of the samples was measured before and after the metallization, and a cost analysis was performed to assess the cost-efficiency. To sum up, the metallization of five samples made with different materials was successfully achieved. Although some 3D printing defects worsened after the post-processing treatment, good homogeneity on the finest details was reached. These promising results may encourage further experimentations as well as the development of new applications, i.e., for the automotive and furniture fields.

Performance of Low-Cost 3D Printer in Medical Application

2021 ◽  
Author(s):  
Nor Aiman Sukindar ◽  
Azib Azhari Awang Dahan ◽  
Sharifah Imihezri Syed Shaharuddin ◽  
Nor Farah Huda Abd Halim
Keyword(s):  
Low Cost ◽  
Medical Application ◽  
Fused Deposition Modelling ◽  
3D Printer ◽  
Layer By Layer ◽  
Total Deformation ◽  
Element Analysis ◽  
Porosity Level ◽  
Fused Deposition ◽  
Printing Parameters

Abstract Fused Deposition Modelling (FDM) is an additive manufacturing (AM) process that produces a physical object directly from a CAD design using layer-by-layer deposition of the filament material that is extruded via a nozzle. In industry, FDM has become one of the most used AM processes for the production of low batch quantity and functional prototypes, due to its safety, efficiency, reliability, low cost, and ability to process manufacturing-grade engineering thermoplastic. Recently, the market is flooded with the availability of low-cost printers produced by numerous companies. This research aims to investigate the effect of different porosity levels on a scaffold structure produced using a low-cost 3D printer. Comparisons of these porous structures were made in terms of Von-Mises strain, total deformation, as well as compressive stress. Various porosity levels were created by varying printing parameters, including layer height, infill density, and shell thickness by slicing the initial solid CAD file using Repetier Host 3D printing software. Finite Element Analysis (FEA) simulation was then performed on the created scaffold structures by using Ansys Workbench 19.2. The simulation result indicates that the greater porosity level will result in higher total deformation of the structure. Meanwhile, the compression test shows that the minimum strength value obtained was favourable at 22 MPa and had exceeded that of the trabecular femur (15 MPa). However, its porosity level (maximum at 52%) was still below that of the minimum threshold of porosity level of 70 percent. However, the printing parameters currently used can be adjusted in the future. Therefore, it was deduced that the low-cost 3D printer offers promising potential to fabricate different porosity structures with multiple outcomes.

scholarly journals Suitability of Recycled PLA Filament Application in Fused Filament Fabrication Process

2021 ◽  
Vol 15 (4) ◽  
pp. 491-497
Author(s):  
Tomislav Breški ◽  
Lukas Hentschel ◽  
Damir Godec ◽  
Ivica Đuretek
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Polylactic Acid ◽  
Design Of Experiment ◽  
Experimental Approach ◽  
Manufacturing Processes ◽  
Support Structures ◽  
Fused Filament Fabrication ◽  
Layer Height ◽  
Printing Parameters

Fused filament fabrication (FFF) is currently one of the most popular additive manufacturing processes due to its simplicity and low running and material costs. Support structures, which are necessary for overhanging surfaces during production, in most cases need to be manually removed and as such, they become waste material. In this paper, experimental approach is utilised in order to assess suitability of recycling support structures into recycled filament for FFF process. Mechanical properties of standardized specimens made from recycled polylactic acid (PLA) filament as well as influence of layer height and infill density on those properties were investigated. Optimal printing parameters for recycled PLA filaments are determined with Design of Experiment methods (DOE).

Tensile properties of the FFF-processed thermoplastic polyurethane (TPU) elastomer

2021 ◽  
Author(s):  
Budi Arifvianto ◽  
Teguh Nur Iman ◽  
Benidiktus Tulung Prayoga ◽  
Rini Dharmastiti ◽  
Urip Agus Salim ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Low Cost ◽  
Thermoplastic Polyurethane ◽  
High Strength ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Fused Filament Fabrication ◽  
Raster Angle ◽  
Manufacturing Techniques

Abstract Fused filament fabrication (FFF) has become one of the most popular, practical, and low-cost additive manufacturing techniques for fabricating geometrically-complex thermoplastic polyurethane (TPU) elastomer. However, there are still some uncertainties concerning the relationship between several operating parameters applied in this technique and the mechanical properties of the processed material. In this research, the influences of extruder temperature and raster orientation on the mechanical properties of the FFF-processed TPU elastomer were studied. A series of uniaxial tensile tests was carried out to determine tensile strength, strain, and elastic modulus of TPU elastomer that had been printed with various extruder temperatures, i.e., 190–230 °C, and raster angles, i.e., 0–90°. Thermal and chemical characterizations were also conducted to support the analysis in this research. The results obviously showed the ductile and elastic characteristics of the FFF-processed TPU, with specific tensile strength and strain that could reach up to 39 MPa and 600%, respectively. The failure mechanisms operating on the FFF-processed TPU and the result of stress analysis by using the developed Mohr’s circle are also discussed in this paper. In conclusion, the extrusion temperature of 200 °C and raster angle of 0° could be preferred to be applied in the FFF process to achieve high strength and ductile TPU elastomer.

Stiffness prediction of 3D printed fiber-reinforced thermoplastic composites

2019 ◽  
Vol 26 (3) ◽  
pp. 549-555
Author(s):  
Jin Young Choi ◽  
Mark Timothy Kortschot
Keyword(s):  
Mechanical Properties ◽  
Extrusion Direction ◽  
Analytical Models ◽  
Thermoplastic Composites ◽  
Fiber Reinforced ◽  
Flat Plates ◽  
Fused Filament Fabrication ◽  
Element Analysis ◽  
Content Type ◽  
3D Printed

Purpose The purpose of this study is to confirm that the stiffness of fused filament fabrication (FFF) three-dimensionally (3D) printed fiber-reinforced thermoplastic (FRP) materials can be predicted using classical laminate theory (CLT), and to subsequently use the model to demonstrate its potential to improve the mechanical properties of FFF 3D printed parts intended for load-bearing applications. Design/methodology/approach The porosity and the fiber orientation in specimens printed with carbon fiber reinforced filament were calculated from micro-computed tomography (µCT) images. The infill portion of the sample was modeled using CLT, while the perimeter contour portion was modeled with a rule of mixtures (ROM) approach. Findings The µCT scan images showed that a low porosity of 0.7 ± 0.1% was achieved, and the fibers were highly oriented in the filament extrusion direction. CLT and ROM were effective analytical models to predict the elastic modulus and Poisson’s ratio of FFF 3D printed FRP laminates. Research limitations/implications In this study, the CLT model was only used to predict the properties of flat plates. Once the in-plane properties are known, however, they can be used in a finite element analysis to predict the behavior of plate and shell structures. Practical implications By controlling the raster orientation, the mechanical properties of a FFF part can be optimized for the intended application. Originality/value Before this study, CLT had not been validated for FFF 3D printed FRPs. CLT can be used to help designers tailor the raster pattern of each layer for specific stiffness requirements.

Effect of extrusion temperature on fused filament fabrication parts orthotropic behaviour

2019 ◽  
Vol 26 (4) ◽  
pp. 639-647
Author(s):  
Michele Angelo Attolico ◽  
Caterina Casavola ◽  
Alberto Cazzato ◽  
Vincenzo Moramarco ◽  
Gilda Renna
Keyword(s):  
Mechanical Properties ◽  
Morphological Characteristics ◽  
Single Layer ◽  
Acrylonitrile Butadiene Styrene ◽  
Surface Characteristics ◽  
Tensile Tests ◽  
Extrusion Temperature ◽  
Fused Filament Fabrication ◽  
Bonding Quality ◽  
Content Type

Purpose The purpose of this paper is to verify the effects of extrusion temperature on orthotropic behaviour of the mechanical properties of parts obtained by fused filament fabrication (FFF) under quasi-static tensile loads. Design/methodology/approach Tensile tests were performed on single layer specimens fabricated in polylactic acid (PLA) and acrylonitrile butadiene styrene (ABS) to evaluate the mechanical properties at different extrusion temperatures and raster orientations (0°, 45° and 90°). Furthermore, a detailed study of morphological characteristics of the single layer samples cross-section and of the bonding quality among adjacent deposited filaments was performed by scanning electron microscopy to correlate the morphology of materials with mechanical behaviour. Findings The results show that the orthotropic behaviour of FFF-printed parts tends to reduce, while the mechanical properties improved with increase in extrusion temperature. Furthermore, the increase in extrusion temperature led to an improvement in inter-raster bonding quality and in the compactness and homogeneity of the parts. Originality/value The relation between the extrusion temperature, orthotropic behaviour and morphological surface characteristics of the single layer specimen obtained by FFF has not been previously reported.

The Precise Determination of the Johnson–Cook Material and Damage Model Parameters and Mechanical Properties of an Aluminum 7068-T651 Alloy

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
B. Bal ◽  
K. K. Karaveli ◽  
B. Cetin ◽  
B. Gumus
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Physical Simulation ◽  
Damage Model ◽  
Rolling Direction ◽  
Stress Triaxiality ◽  
Material Model ◽  
Tensile Tests ◽  
Model Parameters ◽  
Element Analysis

Al 7068-T651 alloy is one of the recently developed materials used mostly in the defense industry due to its high strength, toughness, and low weight compared to steels. The aim of this study is to identify the Johnson–Cook (J–C) material model parameters, the accurate Johnson–Cook (J–C) damage parameters, D1, D2, and D3 of the Al 7068-T651 alloy for finite element analysis-based simulation techniques, together with other damage parameters, D4 and D5. In order to determine D1, D2, and D3, tensile tests were conducted on notched and smooth specimens at medium strain rate, 100 s−1, and tests were repeated seven times to ensure the consistency of the results both in the rolling direction and perpendicular to the rolling direction. To determine D4 and D5 further, tensile tests were conducted on specimens at high strain rate (102 s−1) and temperature (300 °C) by means of the Gleeble thermal–mechanical physical simulation system. The final areas of fractured specimens were calculated through optical microscopy. The effects of stress triaxiality factor, rolling direction, strain rate, and temperature on the mechanical properties of the Al 7068-T651 alloy were also investigated. Damage parameters were calculated via the Levenberg–Marquardt optimization method. From all the aforementioned experimental work, J–C material model parameters were determined. In this article, J–C damage model constants, based on maximum and minimum equivalent strain values, were also reported which can be utilized for the simulation of different applications.

scholarly journals IMCs Microstructure Evolution Dependence of Mechanical Properties for Ni/Sn/Ni Micro Solder-Joints

Materials ◽  
2020 ◽  
Vol 13 (1) ◽  
pp. 252 ◽  
Author(s):  
Ning Ren ◽  
Heng Fang ◽  
Dong Wang ◽  
Chenyi Hou ◽  
Yatao Zhao ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Brittle Fracture ◽  
Ductile Fracture ◽  
Solder Joints ◽  
Volume Fraction ◽  
Tensile Tests ◽  
Stress Concentrations ◽  
Element Analysis ◽  
Scale Down ◽  
Long Rod

The current miniaturization trend of microelectronic devices drives the size of solder joints to continually scale down. The miniaturized joints considerably increase intermetallic compounds (IMCs) volume fraction to trigger mechanical reliability issues. This study investigated precise relationships between varying IMC volumes and mechanical properties of Ni/Sn(20μm)/Ni micro-joints. A designed method that followed the IMC volume as the only variable was used to prepare micro-joint samples with different IMC volumes. The continuously thickened Ni3Sn4 IMCs exhibited a noticeable morphology evolution from rod-like to chunky shape. The subsequent tensile tests showed unexpected tensile strength responses as increasing Ni3Sn4 volume, which was strongly associated with the Ni3Sn4 morphological evolutions. Fractographic analysis displayed that the ductile fracture dominates the 20%–40% IMC micro-joints, whereas the brittle fracture governs the 40%–80% IMC micro-joints. For the ductile fracture-dominated joints, an abnormal reduction in strength occurred as increasing IMCs volume from 20% to 40%. This is primarily due to severe stress concentrations caused by the transformed long rod-typed morphology of the Ni3Sn4. For the brittle fracture-dominated joints, the strength appeared a monotonous increase as the Ni3Sn4 volume increased. This may be attributed to the increased crack resistance resulting from continuous coarsening of the chunky Ni3Sn4 without any voids. Moreover, the finite element analysis was provided to further understand the joint failure mechanisms.

scholarly journals Analysis of the Compression Behaviour of Reinforced Photocurable Materials Used in Additive Manufacturing Processes Based on a Mask Image Projection System

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4605
Author(s):  
Jordi Bonada ◽  
Pol Barcelona ◽  
Miquel Casafont ◽  
Josep Maria Pons ◽  
Jose Antonio Padilla ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Experimental Tests ◽  
Layer By Layer ◽  
Projection System ◽  
Compression Behaviour ◽  
Image Projection ◽  
Key Factor ◽  
Maximum Improvement ◽  
Homogeneous Reinforced ◽  
Reinforced Materials

Mask image projection based on stereolithography is an additive manufactured technology based on a Frontal Photopolymerization Process. Therefore, photocurable resins are used to build-up parts layer by layer. In this paper, alumina particles have been used as a reinforcement filler in order to improve the material stress-strain behaviour. In addition, the increment of the photoconversion ratio is a key factor to enhance the mechanical properties. Consequently, a numerical model has been used to determine the optimal printing parameters to enhance the elastic mechanical properties of printed parts according to the characteristics of photocurable materials. Stable and homogeneous reinforced materials have been obtained with an alumina content ranging from 5 to 15 wt%. Furthermore, the compression behaviour of reinforced materials has been analysed by means of experimental tests. The results show an enhancement of mechanical properties after the addition of reinforcement fillers, obtaining a maximum improvement in 10 wt% of solid load content. Finally, the influence of the sample’s orientation on the construction platform has been discussed.

Sign in / Sign up

Export Citation Format

Share Document