scholarly journals Investigations of High-Strength Mg–Al–Ca–Mn Alloys with a Broad Range of Ca+Al Contents

Materials ◽  
2021 ◽  
Vol 14 (18) ◽  
pp. 5439
Author(s):  
Stefan Gneiger ◽  
Nikolaus P. Papenberg ◽  
Aurel R. Arnoldt ◽  
Carina M. Schlögl ◽  
Martin Fehlbier
Keyword(s):  
Mechanical Performance ◽  
Low Cost ◽  
High Strength Steels ◽  
High Strength ◽  
High Volume ◽  
Mg Alloys ◽  
High Yield ◽  
Low Mass ◽  
Industrial Use ◽  
The Moment

The low mass and high specific stiffness of Mg alloys make them particularly interesting as means of transportation. Due to further desirable properties, such as good machinability and excellent castability, Mg alloys have gained acceptance as castings in high-volume applications, such as gearbox housings and automotive steering wheels. However, in forming processes, such as extrusion and forging, Mg alloys find little to no industrial use at the moment. The reasons for this are their poor formability, which is reflected in limited processing speeds and low ductility, and their modest mechanical performance, compared to competing materials, such as Al alloys and high-strength steels. Much research is being conducted worldwide on high-strength Mg alloys, most of which rely on high levels of rare earths, making these materials both ecologically and economically questionable. Here, it is shown that high yield strengths (> 300 MPa) can be achieved in the Mg–Al–Ca system while maintaining good ductility, using only low-cost elements. The investigations have shown that these properties can be adjusted over broad alloy compositions, which greatly simplifies both the processing and recyclability.

scholarly journals Design of Low-Cost and High-Strength Titanium Alloys Using Pseudo-Spinodal Mechanism through Diffusion Couple Technology and CALPHAD

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2910
Author(s):  
Chaoyi Ding ◽  
Chun Liu ◽  
Ligang Zhang ◽  
Di Wu ◽  
Libin Liu
Keyword(s):  
Diffusion Couple ◽  
Titanium Alloys ◽  
High Throughput ◽  
Volume Fraction ◽  
Raw Materials ◽  
Low Cost ◽  
High Strength ◽  
High Yield ◽  
Α Phase ◽  
Cr System

The high cost of development and raw materials have been obstacles to the widespread use of titanium alloys. In the present study, the high-throughput experimental method of diffusion couple combined with CALPHAD calculation was used to design and prepare the low-cost and high-strength Ti-Al-Cr system titanium alloy. The results showed that ultra-fine α phase was obtained in Ti-6Al-10.9Cr alloy designed through the pseudo-spinodal mechanism, and it has a high yield strength of 1437 ± 7 MPa. Furthermore, application of the 3D strength model of Ti-6Al-xCr alloy showed that the strength of the alloy depended on the volume fraction and thickness of the α phase. The large number of α/β interfaces produced by ultra-fine α phase greatly improved the strength of the alloy but limited its ductility. Thus, we have demonstrated that the pseudo-spinodal mechanism combined with high-throughput diffusion couple technology and CALPHAD was an efficient method to design low-cost and high-strength titanium alloys.

Fatigue and Burst Analysis of Hy-140(T) Steel Pressure Vessels

1970 ◽  
Vol 92 (1) ◽  
pp. 11-16 ◽  
Author(s):  
J. M. Barsom ◽  
S. T. Rolfe
Keyword(s):  
Yield Strength ◽  
Pressure Vessel ◽  
Low Cycle Fatigue ◽  
High Strength Steels ◽  
High Strength ◽  
Fatigue Tests ◽  
Pressure Vessels ◽  
High Yield ◽  
Corrosion Properties ◽  
Burst Analysis

Increasing use of high-strength steels in pressure-vessel design has resulted from emphasis on decreasing the weight of pressure vessels for certain applications. To demonstrate the suitability of a 140-ksi yield strength steel for use in unwelded pressure vessels, HY-140(T)—a quenched and tempered 5Ni-Cr-Mo-V steel—was fabricated and subjected to various burst and fatigue tests, as well as to various laboratory tests. In general, results of the investigation indicated very good tensile, Charpy, Nil Ductility Transition Temperature (NDT), low-cycle fatigue, and stress-corrosion properties of HY-140(T) steels, as well as very good burst tests results, in comparison with existing high-yield strength pressure-vessel steels. The results also indicate that the HY-140(T) steel should be an excellent material for its originally designed purpose, Naval hull applications.

Third generation of advanced high-strength steels: Processing routes and properties

2016 ◽  
Vol 233 (2) ◽  
pp. 209-238 ◽  
Author(s):  
Tarun Nanda ◽  
Vishal Singh ◽  
Virender Singh ◽  
Arnab Chakraborty ◽  
Sandeep Sharma
Keyword(s):  
Automobile Industry ◽  
Second Generation ◽  
Low Cost ◽  
High Strength Steels ◽  
High Strength ◽  
Cost Effective ◽  
Processing Route ◽  
Third Generation ◽  
Specific Strength ◽  
Advanced High Strength Steels

The automobile industry is presently focusing on processing of advanced steels with superior strength–ductility combination and lesser weight as compared to conventional high-strength steels. Advanced high-strength steels are a new class of materials to meet the need of high specific strength while maintaining the high formability required for processing, and that too at reasonably low cost. First and second generation of advanced high-strength steels suffered from some limitations. First generation had high strength but low formability while second generation possessed both strength and ductility but was not cost effective. Amongst the different types of advanced high-strength steels grades, dual-phase steels, transformation-induced plasticity steels, and complex phase steels are considered as very good options for being extended into third generation advanced high-strength steels. The present review presents the various processing routes for these grades developed and discussed by different authors. A novel processing route known as quenching and partitioning route is also discussed. The review also discusses the resulting microstructures and mechanical properties achieved under various processing conditions. Finally, the key findings with regards to further research required for the processing of advanced high-strength steels of third generation have been discussed.

Metallurgical Study of Friction Stir Welded High Strength Steels for Shipbuilding

2014 ◽  
Vol 783-786 ◽  
pp. 2798-2803 ◽  
Author(s):  
Marion Allart ◽  
Alexandre Benoit ◽  
Pascal Paillard ◽  
Guillaume Rückert ◽  
Myriam Chargy
Keyword(s):  
Cubic Boron Nitride ◽  
High Strength Steels ◽  
High Strength ◽  
High Yield ◽  
Friction Stir ◽  
Polycrystalline Cubic Boron Nitride ◽  
Recent Developments ◽  
Metallurgical Study ◽  
Welding Processes ◽  
Pcbn Tools

Friction Stir Welding (FSW) is one of the most recent welding processes, invented in 1991 by The Welding Institute. Recent developments, mainly using polycrystalline cubic boron nitride (PCBN) tools, broaden the range of use of FSW to harder materials, like steels. Our study focused on the assembly of high yield strength steels for naval applications by FSW, and its consequences on the metallurgical properties. The main objectivewas to analyze the metallurgical transformations occurring during welding. Welding tests were conducted on three steels: 80HLES, S690QL and DH36. For each welded sample, macrographs, micrographs and micro-hardness maps were performed to characterize the variation of microstructures through the weld.

Influence of the Processing Variables on the Microstructure Evolution of a Bainitic Carbide-Free Steel

2016 ◽  
Vol 879 ◽  
pp. 867-872 ◽  
Author(s):  
M.C. Taboada ◽  
I. Gutiérrez ◽  
D. Jorge-Badiola ◽  
S.M.C. van Bohemen ◽  
F. Hisker ◽  
...  
Keyword(s):  
Retained Austenite ◽  
High Strength Steels ◽  
High Strength ◽  
High Volume ◽  
X Ray Diffraction ◽  
Tempered Martensite ◽  
Trip Steels ◽  
Volume Fractions ◽  
Advanced High Strength Steels ◽  
Processing Variables

New trends focused on achieving higher performance steels has led to a so-called 3rd Generation Advanced High Strength Steels (AHSS), in which the typical polygonal ferrite found in TRIP steels as a matrix phase is replaced by harder phases as Carbide-Free Bainite (CFB) and/or (tempered) martensite. Besides, large volume fractions of retained austenite (R.A.) with adequate stability are aimed for to improve the formability of the steels. Si containing steels are regarded as the most suitable to retard cementite formation and consequently reach high volume fractions of RA. In this work, CFB annealing schedules were applied to dilatometer samples of Fe-0.22C-2.0Mn-1.3Si. The overaging temperature TB was varied between 390 oC and 480 oC, and other processing variables investigated were the austenitizing temperature Taus, and the overaging holding time tB. The annealed samples analyzed with LOM, FEG-SEM, EBSD and X-ray diffraction techniques show that markedly different complex microstructures made up of bainite, ferrite, MA phase and retained austenite (R.A) are accomplished depending on the specific thermal cycle. These results are described in detail and discussed in relation to the dilatometry measurements.

SUSTAINABLE ULTRA-HIGH-PERFORMANCE GLASS CONCRETE FOR INFRASTRUCTURES

2017 ◽  
Vol 4 (1) ◽  
Author(s):  
Arezki Tagnit-Hamou ◽  
Nancy A. Soliman
Keyword(s):  
High Performance ◽  
Glass Powder ◽  
Mechanical Performance ◽  
High Performance Concrete ◽  
Low Cost ◽  
Research Work ◽  
High Strength ◽  
Quartz Powder ◽  
Ultra High Performance Concrete ◽  
Powder Particles

This paper presents research work on the development of a green type of ultra-high-performance concrete using ground glass powders with different degrees of fineness (UHPGC). This article presents the development of an innovative, low-cost, and sustainable UHPGC through the use of glass powder to replace cement, and quartz powder particles. An UHPGC with a compressive strength (fc) of up to 220 MPa was prepared and its fresh, and mechanical properties were investigated. The test results indicate that the fresh UHPGC properties were improved when the cement and quartz powder were replaced with non-absorptive glass powder particles. The strength improvement can be attributed to the glass powder’s pozzolanicity and to its mechanical performance (very high strength and elastic modulus of glass). A case study of using this UHPGC is presented through the design and construction of a footbridge. Erection of footbridge at University of Sherbrooke Campus using UHPGC is also presented as a full-scale application.

Tools and Technologies for Hot Forming with Local Adjustment of Part Properties

2010 ◽  
Vol 638-642 ◽  
pp. 3919-3924 ◽  
Author(s):  
Ralf Kolleck ◽  
Robert Veit
Keyword(s):  
High Strength Steels ◽  
High Strength ◽  
Strength Distribution ◽  
Body Parts ◽  
Press Hardening ◽  
Uniform Strength ◽  
University Of Technology ◽  
Ultra High Strength Steels ◽  
Conventional Press ◽  
The Moment

In general hot stamped car body parts show a uniform strength distribution. Especially for safety relevant parts with high requirements concerning crash performance, this uniform strength distribution can cause problems. During a crash a B-pillar e. g. can absorb more energy when the lower part is relatively flexible while the middle and upper part has to be high-tensile to prevent the intrusion into the passenger compartment. Also during the production of hot stamped parts, the high strength causes trouble. When the trimming takes place after the hardening process, the durability of the tool is limited. Thus at the moment the only economic process for trimming of ultra-high-strength steels is laser cutting. This paper presents different approaches to reach local different strength distributions in hot stamped components. In particular the results of a research project of the Institute Tools & Forming, Graz University of Technology are shown where precisely defined areas of different strengths could be obtained in one part. This was achieved by the use of simple and cheap ceramic inserts in conventional press hardening tools.

The Role of Niobium in Lightweight Vehicle Construction

2007 ◽  
Vol 537-538 ◽  
pp. 679-686 ◽  
Author(s):  
Hardy Mohrbacher ◽  
Christian Klinkenberg
Keyword(s):  
Grain Refinement ◽  
High Strength Steel ◽  
Mechanical Performance ◽  
High Strength Steels ◽  
High Strength ◽  
Interstitial Free ◽  
Niobium Microalloying ◽  
Hsla Steels ◽  
Steel Grades ◽  
Different Characteristics

Modern vehicle bodies make intensive use of high strength steel grades to improve the weight and the mechanical performance simultaneously. A broad range of medium and extra high strength steel grades is available. These steel grades have different characteristics concerning strength, formability and weldability. For many steel grades microalloying by niobium is the key to achieve their characteristic property profile. In HSLA steels niobium enhances the strength primarily by grain refinement. In interstitial free high strength steels niobium serves as a stabilizing element and also assists in obtaining the bake hardening effect. Some modern multiphase steels rely on niobium to achieve additional strength via grain refinement and precipitation hardening. Microstructural control provides a way to further optimize properties relevant to automotive processing such as cutting, forming and welding. The relevance of niobium microalloying in that respect will be outlined.

Finite Element Simulation of Chain-Die Forming U Profiles with Variable Cross-Section

2017 ◽  
Vol 898 ◽  
pp. 1177-1182 ◽  
Author(s):  
Y.G. Li ◽  
Y. Sun ◽  
H.L. Huang ◽  
D.Y. Li ◽  
S.C. Ding
Keyword(s):  
Finite Element ◽  
Cross Section ◽  
Low Cost ◽  
High Strength Steels ◽  
High Strength ◽  
Variable Cross Section ◽  
Roll Forming ◽  
Variable Cross ◽  
Advanced High Strength Steels ◽  
Die Forming

Roll forming has been widely used to manufacture constant cross-section products because of high quality, efficiency and low cost. It is quite epidemic in producing automobile parts made of advanced high strength steels (AHSS) nowadays. However, with the development of the vehicle industry and diversity of the products, variable cross-section profiles have attracted more and more attention. The traditional roll forming technique is difficult to meet the requirements. Chain-die forming which was introduced in recent years makes it possible. Chain-die forming is an extension of roll forming and its key characteristic is enlarging the rotation radii of the moulds, by which the deformation zone is extended. The study focused on the finite element simulations of Chain-die forming U profiles with variable cross-section, including variable width and height. The feasibility of Chain-die forming producing variable cross-section products was verified by the perfect simulation results. The advantage of Chain-die forming was that there was no need to design the intermediate moulds except the finished-profile ones, which reduced the mould quantity immensely. Then the cost was lower.

Sign in / Sign up

Export Citation Format

Share Document