scholarly journals Work Hardening of Heat-Treated AlSi10Mg Alloy Manufactured by Single and Double Laser Selective Laser Melting: Effects of Layer Thickness and Hatch Spacing

Materials ◽  
2021 ◽  
Vol 14 (17) ◽  
pp. 4901
Author(s):  
Emanuele Ghio ◽  
Emanuela Cerri
Keyword(s):  
Heat Treatment ◽  
Layer Thickness ◽  
Work Hardening ◽  
Cast Alloy ◽  
Work Conditions ◽  
Heat Treated ◽  
Direct Aging ◽  
Before And After ◽  
Aging Phenomena ◽  
Hatch Spacing

The present study analyzed the microstructure and the mechanical properties of AlSi10Mg SLMed bars (10 × 10 × 300 mm) and billets (10 × 100 × 300 mm) before and after the direct aging at 200 °C for 4 h and the T6 heat treatment. The discussed results are compared to those obtained by the AlSi10Mg samples manufactured with the same geometry but using different process parameters (layer thickness higher than 40 μm and a hatch spacing lower than 100 μm) and also through the Quality Index (QI). These work conditions allow the obtaining of a microstructural variation and different tensile properties in as-built top samples. In both batches, the cycle time was 45 h and together with the preheated build platform at 150 °C, induced an increase of UTS (Ultimate Tensile Strength) and yield strength on the bottom rather than the top samples due to the aging phenomena. Upon completion of the direct aging heat treatment, the effects induced by the platform were cancelled, keeping a full cellular microstructure that characterized the as-built SLMed (Selective Laser Melted) samples. Moreover, the Considère criterion and the work hardening analysis showed that the failure occurs after the necking formation in some of the T6 heat-treated samples. In this last case, the Si eutectic network globularized into Si particles, causing a decrease of UTS (from around 400 MPa to 290 MPa) in favour of an increase of ductility up to 15% and reaching a QI in the range 400 ÷ 450 MPa. These values place these samples between the high-quality aluminium cast alloy and T6 heat-treated ones.

Failure analysis of heat treated HSLA wheel bolt steels

2010 ◽  
Vol 6 (3) ◽  
pp. 373-382
Author(s):  
Ali Nazari ◽  
Shadi Riahi
Keyword(s):  
Heat Treatment ◽  
Tensile Strength ◽  
Failure Analysis ◽  
Heat Treating ◽  
Boron Steel ◽  
Content Type ◽  
Heat Treated ◽  
Before And After ◽  
Molybdenum Steel ◽  
Optimum Heat

PurposeThe aims of this study is to analyze failure of two types of high‐strength low‐alloy (HSLA) steels which are used in wheel bolts 10.9 grade, boron steel and chromium‐molybdenum steel, before and after heat treatment.Design/methodology/approachThe optimum heat treatment to obtain the best tensile behavior was determined and Charpy impact and Rockwell hardness tests were performed on the two steel types before and after the optimum heat treating.FindingsFractographic studies show a ductile fracture for heat‐treated boron steel while indicate a semi‐brittle fracture for heat‐treated chromium‐molybdenum steel. Formation of a small boron carbide amount during heat treating of boron steel results in increment the bolt's tensile strength while the ductility did not changed significantly. In the other hand, formation of chromium and molybdenum carbides during heat treating of chromium‐molybdenum steel increased the bolt's tensile strength with a considerable reduction in the final ductility.Originality/valueThis paper evaluates failure analysis of HSLA wheel bolt steels and compares their microstructure before and after the loading regime.

scholarly journals Study on the Properties of Transparent Bamboo Prepared by Epoxy Resin Impregnation

Polymers ◽  
2020 ◽  
Vol 12 (4) ◽  
pp. 863 ◽  
Author(s):  
Yan Wu ◽  
Yajing Wang ◽  
Feng Yang ◽  
Jing Wang ◽  
Xuehua Wang
Keyword(s):  
Heat Treatment ◽  
Tensile Strength ◽  
Visible Light ◽  
Epoxy Resin ◽  
Raw Materials ◽  
Light Transmittance ◽  
Advantages And Disadvantages ◽  
Heat Treated ◽  
Before And After ◽  
Different Parts

In this paper, Moso bamboo (Phyllostachys heterocycle) before and after heat treatment were used as raw materials to prepare transparent bamboo (TB). In an acidic environment, the lignin contained in the bamboo material was removed to obtain a bamboo template, and an epoxy resin similar to the cellulose refractive index was used for vacuum impregnation into the bamboo template to obtain a transparent bamboo material. The purpose of this study was to compare the physical and chemical properties of TB and original bamboo and the differences between TBs before and after heat treatment, taken from different parts of bamboo, in order to explore the performance advantages and disadvantages of TB as a new material. The Fourier transform infrared spectroscopy analysis (FTIR), scanning electron microscope testing (SEM), three elements analysis, light transmittance testing, and mechanical strength testing were used to study the molecular composition, microstructure, chemical composition, light transmittance, and tensile strength of the TB samples. The results showed that the lignin content of the delignified bamboo templates was greatly reduced. In addition, the SEM images showed that a large amount of epoxy resin (type E51 and type B210 curing agent) was covered on the cross-section surface and pores of the TB samples. The FTIR showed that the epoxy molecular groups appeared on the TB, and the delignified bamboo template and the resin had a good synergy effect. According to the light transmittance testing, the original bamboo samples hardly contained light transmittance under visible light. The transmittance of transparent inner bamboo (TIB) and transparent heat-treated inner bamboo (THIB) could reach about 11%, and the transmittance of transparent outer bamboo (TOB) and transparent heat-treated outer bamboo (THOB) was about 2%. The light transmittance had been significantly improved when compared with the original bamboo samples. The transmittances of the TB samples before and after heat treatment in different parts of bamboo were different. In the visible light irradiation range, the light transmittances of TB samples were as follows: TIB > THIB and THOB > TOB. Meanwhile, the tensile strength of TB was reduced, especially for TOB and THOB. In addition, TB has a wide range of raw materials, and the preparation process is environmentally friendly. It can be used for decorative materials in homes, buildings, etc., and has a great application potential.

The Microstructure and Compression Behavior of Multi-Step Forging Ti-45Al-8Nb Alloy after Annealing at 1100 °C

2013 ◽  
Vol 747-748 ◽  
pp. 111-114
Author(s):  
Lin Song ◽  
Xiang Jun Xu ◽  
Jun Pin Lin ◽  
Lai Qi Zhang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Annealing Treatment ◽  
Air Cooling ◽  
Test Machine ◽  
Compressive Properties ◽  
Compression Behavior ◽  
Microstructure Change ◽  
Heat Treated ◽  
Before And After

Effects of annealing treatment on microstructure and the compressive properties of hot-worked Ti-45Al-8Nb-(W, B, Y) alloy were investigated. Microstructure of the extrusion plus multi-step forging pancake before and after heat treatment was analyzed by SEM and TEM, respectively. The annealing was conducted by holding samples at 1100°C for 2hrs, and followed by air cooling and furnace cooling. The mechanical properties were measured by Instron test machine. The microstructure evolution during compressive deformation was analyzed by TEM. The results showed that after the annealing the microstructure change could not be observed under SEM but can be observed under TEM. Many dislocation clusters were removed by heat treatment. The heat treated samples had similar compression behaviors with the pancake. TEM investigation showed that the numerous twin intersections occured in γ matrix during compression. The twin spaces tended to decrease as the deformation and the intersection increasing.

Casting and Heat Treatment of Turbocharger Impellers Thixocast from Alloy 201

2012 ◽  
Vol 192-193 ◽  
pp. 556-561 ◽  
Author(s):  
Qiang Zhu ◽  
Stephen Midson ◽  
Chang Wei Ming ◽  
Helen V. Atkinson
Keyword(s):  
Heat Treatment ◽  
High Strength ◽  
Heat Treatment Condition ◽  
Hot Tearing ◽  
Alloy Casting ◽  
Heat Treated ◽  
Before And After ◽  
Optimum Heat ◽  
Semi Solid ◽  
Optimum Heat Treatment

Commercial semi-solid cast impellers are produced from Al-Si-Cu alloys heat treated to the T6 temper. The study described in this paper involved the identification of casting and heat treatment parameters to produce semi-solid processed turbocharger impellers from a silicon-free, higher strength 201 alloy. Casting parameters were identified which minimized hot tearing in the alloy 201 impellers. A series of heat treatment studies were performed to determine optimum heat treatment parameters. The T71 temper was identified as the preferred heat treatment condition to produce high strength as well as superior elongation. The results from mechanical property measurements conducted on the T71 heat treated impellers are reported. Optical and scanning electron microscopy (SEM) were also used to characterize the microstructure of alloy 201 impellers before and after heat treatment, and representative microstructures are presented.

The Effect of Semi-Solid Parameters on the Microstructure and Hardness of High Chromium Cast Irons

2010 ◽  
Vol 457 ◽  
pp. 84-89 ◽  
Author(s):  
Arash Inanlou ◽  
S. Hossein Seyedein ◽  
M. Reza Aboutalebi
Keyword(s):  
Heat Treatment ◽  
Casting Process ◽  
Cast Irons ◽  
Inclined Plate ◽  
Cooling Plate ◽  
High Chromium ◽  
Primary Austenite ◽  
Heat Treated ◽  
Before And After ◽  
Semi Solid

High chromium cast iron samples of 14% Cr and 24% Cr were produced in sand and permanent mold using semi-solid casting process. A series of experiments were carried out to clarify the effect of copper cooling plate and mold cooling rate on microstructure, particularly morphology and sphericity of primary austenite, hardness and heat treatment cycles. Results show that for 14% Cr and 24% cast irons casting at 10 and 15 degrees of inclined plate result in better sphericity and distribution of primary austenite and carbides. Moreover hardness comparison of both semi-solid iron alloys using copper cooling plate at of this special morphologies resulted from cooling plate investigated by making them heat treat at 1050 centigrade °C for 1 and 2 hours. Hardness results show both heat treated 14 and 24% Cr alloy in 1 hours have hardness comparable with those alloys traditionally cast optimum angles with respect to conventional casting show higher hardness in every condition. Effect but heat treated in 2 hours. Finally X-Ray diffraction pattern taken from specimens before and after heat treatment confirmed with observed phases in optical microscopy before and after heat treatment.

Wettability of Heat-Treated Wood

Holzforschung ◽  
2003 ◽  
Vol 57 (3) ◽  
pp. 301-307 ◽  
Author(s):  
M. Pétrissans ◽  
P. Gérardin ◽  
I. El bakali ◽  
M. Serraj
Keyword(s):  
Heat Treatment ◽  
Water Drop ◽  
Chemical Change ◽  
Treated Wood ◽  
Untreated Wood ◽  
Adsorbed Water ◽  
Inert Atmosphere ◽  
Contact Angles ◽  
Heat Treated ◽  
Before And After

Summary The aim of this work was to study the wettability and chemical composition of heat-treated wood. Heat treatment was performed at 240°C under inert atmosphere on four European wood species (pine, spruce, beech and poplar). Contact angle measurements before and after treatment indicated a significant increase in wood hydrophobicity. Advancing contact angles of a water drop were in all cases systematically higher for heat-treated than for untreated wood. Chemical modifications of wood after heat treatment were investigated using FTIR and 13C NMR analysis. FTIR spectra indicated little structural change which could be attributed either to carbon-carbon double bond formation or to adsorbed water. NMR spectra also revealed little chemical change except for the degree of cellulose crystallinity which was considerably higher in heat-treated wood and could explain the higher contact angles.

Characterization of Ni-P and Ni-P-Al2O3 Heat Treated Layers

2017 ◽  
Vol 1143 ◽  
pp. 26-31
Author(s):  
Lucica Balint ◽  
Gina Genoveva Istrate
Keyword(s):  
Electron Microscopy ◽  
Heat Treatment ◽  
Corrosion Resistance ◽  
Composite Coatings ◽  
Treatment Temperature ◽  
Initial State ◽  
X Ray ◽  
Transmission Electron ◽  
Heat Treated ◽  
Before And After

Research has shown the relationship among hardness, usage and corrosion resistance Ni-P-Al2O3 composite coatings on steel support heat treated. The electroless strips were heat treated at 200°C, 300°C, 400°C, 500°C and 600°C. Further studies on corrosion, hardness and usage revealed changes in properties, compared to the initial state, both on the strips coated with Ni-P and the ones coated with Ni-P-Al2O3 composite. The samples have been studied before and after the heat treatment via Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), Energy Dispersive X-ray Analysis (EDX) and X-Ray Diffraction (XRD). The results show that untreated Ni-P layers exhibit strong corrosion resistance, while hardness and usage increase with heat treatment temperature, with a peak at 400 °C. Using suspended particles co-deposition, led to new types of layers, some with excellent hardness and usage properties. Corrosion resistance increase with heat treatment. Coating layers can be adjusted to the desired characteristics, by selecting proper parameters for the expected specific results.

scholarly journals Investigation of intercritical heat treatment temperature effect on microstructure and mechanical properties of dual phase (DP) steel

10.30544/293 ◽  
2017 ◽  
Vol 23 (2) ◽  
pp. 143-152
Author(s):  
Mohammad Davari ◽  
Mehdi Mansouri Hasan Abadi
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Work Hardening ◽  
Heat Treatment Temperature ◽  
Treatment Temperature ◽  
Dual Phase ◽  
Work Hardening Behavior ◽  
Hardening Behavior ◽  
Heat Treated ◽  
Intercritical Heat Treatment

In the present study, the effect of intercritical heat treatment temperature on the tensile properties and work hardening behavior of ferritic-martensitic dual-phase steel have been investigated utilizing tensile test, microhardness measurement and microscopic observation. Plain carbon steel sheet with a thickness of 2 mm was heat treated at 760, 780, 800, 820 and 840 °C intercritical temperatures. The results showed that martensite volume fraction (Vm) increases from 32 to 81%with increasing temperature from 760 to 840 °C. The mechanical properties of samples were examined by tensile and microhardness tests. The results revealed that yield strength was increased linearly with the increase in Vm, but the ultimate strength was increased up to 55% Vm and then decreased afterward. Analyzing the work hardening behavior in term of Hollomon equation showed that in samples with less than 55% Vm, the work hardening took place in one stage and the work hardening exponent increased with increasing Vm. More than one stage was observed in the work hardening behavior when Vm was increased. The results of microhardness test showed that microhardness of the martensite is decreased by increase in heat treatment temperature while the ferrite microhardness is nearly constant for all heat-treated samples.

scholarly journals Short Heat Treatments for the F357 Aluminum Alloy Processed by Laser Powder Bed Fusion

Materials ◽  
2021 ◽  
Vol 14 (20) ◽  
pp. 6157
Author(s):  
Matteo Vanzetti ◽  
Enrico Virgillito ◽  
Alberta Aversa ◽  
Diego Manfredi ◽  
Federica Bondioli ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Precipitation Hardening ◽  
Solution Treatment ◽  
Heat Treatments ◽  
Point Of View ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Heat Treated ◽  
Direct Aging

Conventionally processed precipitation hardening aluminum alloys are generally treated with T6 heat treatments which are time-consuming and generally optimized for conventionally processed microstructures. Alternatively, parts produced by laser powder bed fusion (L-PBF) are characterized by unique microstructures made of very fine and metastable phases. These peculiar features require specifically optimized heat treatments. This work evaluates the effects of a short T6 heat treatment on L-PBF AlSi7Mg samples. The samples underwent a solution step of 15 min at 540 °C followed by water quenching and subsequently by an artificial aging at 170 °C for 2–8 h. The heat treated samples were characterized from a microstructural and mechanical point of view and compared with both as-built and direct aging (DA) treated samples. The results show that a 15 min solution treatment at 540 °C allows the dissolution of the very fine phases obtained during the L-PBF process; the subsequent heat treatment at 170 °C for 6 h makes it possible to obtain slightly lower tensile properties compared to those of the standard T6. With respect to the DA samples, higher elongation was achieved. These results show that this heat treatment can be of great benefit for the industry.

scholarly journals The Effect of Cooling Rate on Mechanical Properties of Carbon Steel (St 35)

2014 ◽  
Vol 7 (1) ◽  
pp. 109-118
Author(s):  
Jenan Mohammed Nagie
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Carbon Steel ◽  
Cooling Rate ◽  
Experimental Results ◽  
Heat Treated ◽  
Before And After ◽  
Water Media ◽  
The Relationship

This paper is aimed to study the effect of cooling rate on mechanical properties of Steel 35. Specimens prepared to apply tensile, torsion, impact and hardness tests.Many prepared specimens heat treated at (850ºC) for one hour and subsequently were cooled by three different media [Water-Air-furnace] to show the effect of Medias cooling rate on mechanical properties. Microstructures of all specimens examined before and after heat treatment by an optical microscopy.To figure the phases obtained after heat treatment and its effect on the mechanical properties Experimental results have shown that the microstructure of steel can be changed and significantly improved by varying line cooling rate thus, improving one property will effect on the others because of the relationship between all properties.In water media tensile, torsion and hardness improved while impact results reduced. Air media contributed in improving most of the mechanical properties because of grain size homogeneity. At furnace media ductility and impact improved

Sign in / Sign up

Export Citation Format

Share Document