scholarly journals Thermal Properties and the Prospects of Thermal Energy Storage of Mg–25%Cu–15%Zn Eutectic Alloy as Phase Change Material

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3296
Author(s):  
Zheng Sun ◽  
Linfeng Li ◽  
Xiaomin Cheng ◽  
Jiaoqun Zhu ◽  
Yuanyuan Li ◽  
...  
Keyword(s):  
Energy Storage ◽  
Phase Change ◽  
Phase Change Material ◽  
Thermal Energy ◽  
Eutectic Alloy ◽  
Thermal Energy Storage ◽  
Thermal Cycles ◽  
Phase Change Temperature ◽  
Change Temperature ◽  
Change Material

This study focuses on the characterization of eutectic alloy, Mg–25%Cu–15%Zn with a phase change temperature of 452.6 °C, as a phase change material (PCM) for thermal energy storage (TES). The phase composition, microstructure, phase change temperature and enthalpy of the alloy were investigated after 100, 200, 400 and 500 thermal cycles. The results indicate that no considerable phase transformation and structural change occurred, and only a small decrease in phase transition temperature and enthalpy appeared in the alloy after 500 thermal cycles, which implied that the Mg–25%Cu–15%Zn eutectic alloy had thermal reliability with respect to repeated thermal cycling, which can provide a theoretical basis for industrial application. Thermal expansion and thermal conductivity of the alloy between room temperature and melting temperature were also determined. The thermophysical properties demonstrated that the Mg–25%Cu–15%Zn eutectic alloy can be considered a potential PCM for TES.

scholarly journals The Use of Eutectic Fe-Si-B Alloy as a Phase Change Material in Thermal Energy Storage Systems

Materials ◽  
2019 ◽  
Vol 12 (14) ◽  
pp. 2312 ◽  
Author(s):  
Jianmeng Jiao ◽  
Bettina Grorud ◽  
Caroline Sindland ◽  
Jafar Safarian ◽  
Kai Tang ◽  
...  
Keyword(s):  
Energy Storage ◽  
Melting Point ◽  
Phase Change ◽  
Phase Change Material ◽  
Refractory Material ◽  
Thermal Energy ◽  
Eutectic Alloy ◽  
Thermal Energy Storage ◽  
Graphite Crucible ◽  
Change Material

Fe-26.38Si-9.35B eutectic alloy is proposed as a phase change material (PCM) as it exhibits high latent heat, high thermal conductivity, moderate melting point, and low cost. For successful implementation of it in the latent heat thermal energy storage (LHTES) systems, we investigate the use of graphite as a refractory material that withstands long-term melting/solidification in contact with the Fe-26.38Si-9.35B alloy. The PCM has been thermally cycled up to 1–4 times below and above its melting point at the temperature interval of 20 °C or 100 °C. It is observed that this eutectic alloy shows good thermal stability over a small temperature range of 1057–1257 °C. Some SiC and B4C solid precipitation will be formed at the top of the alloy. However, it does not seem to increase with time. The graphite crucible as a refractory material will produce a protective layer of SiC and B4C that will hinder the interaction between the PCM and the crucible. The small volume change during solidification will not break the graphite crucible during cycling. The chemical wear or dissolution of the crucible is negligible. It demonstrates the viability of Fe-26.38Si-9.35B alloy as a heat storage material in this type of container.

Thermal Energy Storage Through Melting of a Commercial Phase Change Material in an Annulus with Radially Divergent Longitudinal Fins

2020 ◽  
Vol 7 (1) ◽  
Author(s):  
Tonny Tabassum Mainul Hasan ◽  
Latifa Begum
Keyword(s):  
Energy Storage ◽  
Phase Change ◽  
Phase Change Material ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Storage System ◽  
Operating Conditions ◽  
Melting Time ◽  
Bottom Part ◽  
Change Material

This study reports on the unsteady two-dimensional numerical investigations of melting of a paraffin wax (phase change material, PCM) which melts over a temperature range of 8.7oC. The PCM is placed inside a circular concentric horizontal-finned annulus for the storage of thermal energy. The inner tube is fitted with three radially diverging longitudinal fins strategically placed near the bottom part of the annulus to accelerate the melting process there. The developed CFD code used in Tabassum et al., 2018 is extended to incorporate the presence of fins. The numerical results show that the average Nusselt number over the inner tube surface, the total melt fraction, the total stored energy all increased at every time instant in the finned annulus compared to the annulus without fins. This is due to the fact that in the finned annulus, the fins at the lower part of the annulus promotes buoyancy-driven convection as opposed to the slow conduction melting that prevails at the bottom part of the plain annulus. Fins with two different heights have been considered. It is found that by extending the height of the fin to 50% of the annular gap about 33.05% more energy could be stored compared to the bare annulus at the melting time of 82.37 min for the identical operating conditions. The effects of fins with different heights on the temperature and streamfunction distributions are found to be different. The present study can provide some useful guidelines for achieving a better thermal energy storage system.

Sign in / Sign up

Export Citation Format

Share Document