scholarly journals The Influence of Tool Shape and Process Parameters on the Mechanical Properties of AW-3004 Aluminium Alloy Friction Stir Welded Joints

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3244
Author(s):  
Anna Janeczek ◽  
Jacek Tomków ◽  
Dariusz Fydrych
Keyword(s):  
Mechanical Properties ◽  
Aluminium Alloy ◽  
Welding Speed ◽  
Welded Joints ◽  
Rotational Speed ◽  
Welding Parameters ◽  
Friction Stir ◽  
Tool Shape ◽  
Joint Quality ◽  
Fsw Parameters

The purpose of the following study was to compare the effect of the shape of a tool on the joint and to obtain the values of Friction Stir Welding (FSW) parameters that provide the best possible joint quality. The material used was an aluminium alloy, EN AW-3004 (AlMn1Mg1). To the authors’ best knowledge, no investigations of this alloy during FSW have been presented earlier. Five butt joints were made with a self-developed, cylindrical, and tapered threaded tool with a rotational speed of 475 rpm. In order to compare the welding parameters, two more joints with a rotational speed of 475 rpm and seven joints with a welding speed of 300 mm/min with the use of a cylindrical threaded pin were performed. This involved a visual inspection as well as a tensile strength test of the welded joints. It was observed that the value of the material outflow for the joints made with the cylindrical threaded pin was higher than it was for the joints made with the tapered threaded pin. However, welding defects in the form of voids appeared in the joints made with the tapered threaded tool. The use of the cylindrical tool resulted in higher values for about 37% of mechanical properties compared with the highest result for the tapered threaded joint. As far as the parameters were concerned, it was concluded that most of the specimens were properly joined for a rotational speed of 475 rpm. In the joints made with a welding speed of 300 mm/min, the material was not stirred properly. The best joint quality was given for a rotational speed of 475 rpm as well as a variety of welding speed values between 150 and 475 mm/min.

Mechanical Property of Friction Stir Welded Retardant Magnesium Alloy Joint

2011 ◽  
Vol 295-297 ◽  
pp. 1929-1932
Author(s):  
Yi Min Tu ◽  
Ran Feng Qiu ◽  
Hong Xin Shi ◽  
Xin Zhang ◽  
Ke Ke Zhang
Keyword(s):  
Mechanical Properties ◽  
Mechanical Property ◽  
Friction Stir Welding ◽  
Magnesium Alloy ◽  
Welding Speed ◽  
Rotational Speed ◽  
Maximum Strength ◽  
Welding Parameters ◽  
Tool Rotational Speed ◽  
Friction Stir

In order to obtain better understanding of the friction stir weldability of the magnesium alloy and provide some foundational information for improving mechanical properties of retardant magnesium alloy joints. A retardant magnesium alloy was weld using the method of friction stir welding. The influence of welding parameters on the strength of the joint was investigated. The maximum strength of 230 MPa was obtained from the joint welded at the tool rotational speed of 1000 r/min and welding speed of 750 mm/min.

scholarly journals Mechanical properties and microstructural characteristics of friction stir welded AA2014-T6 aluminium alloy joints

2019 ◽  
Vol 28 (1) ◽  
pp. 169-185 ◽  
Author(s):  
Chinnasamy Rajendran ◽  
Kasi Srinivasan ◽  
Visvalingam Balasubramanian ◽  
Haridasu Balaji ◽  
Ponnumuthu Selvaraj
Keyword(s):  
Aluminium Alloy ◽  
Tilt Angle ◽  
Welding Speed ◽  
Rotational Speed ◽  
Welding Parameters ◽  
Microstructural Characteristics ◽  
Friction Stir ◽  
Shoulder Diameter ◽  
Working Parameters

AbstractThe quality of friction stir welded joints depends upon the working parameters such as rotational speed, welding speed, shoulder diameter, tilt angle; etc. Each process parameter has a significant effect on the formation of joint strength. This investigation attempts to understand the effect of friction stir welding parameters on microstructural characteristics and tensile strength of AA2014-T6 aluminium alloy. This is performed by changing any one of the process parameters from minimum to maximum and keeping others constant. The joint fabricated from a rotational speed of 1500 rpm, welding speed of 40 mm/min, shoulder diameter of 6 mm and tilt angle of 1.5∘ yielded superior tensile properties compared to their counter joints. Due to the formation of defect-free weld, balanced material flow and uniform distribution of strengthening precipitates in the stir zone is achieved.

scholarly journals Effect of Tool Geometry and Welding Speed on Mechanical Properties and Microstructure of Friction Stir Welded Joints of Aluminium Alloys AA6082-T6

2014 ◽  
Vol 61 (3) ◽  
pp. 455-468
Author(s):  
Hiralal Subhash Patil ◽  
Sanjay N. Soman
Keyword(s):  
Mechanical Properties ◽  
Welding Speed ◽  
Welded Joints ◽  
Aluminium Alloys ◽  
Tensile Tests ◽  
Tool Geometry ◽  
Welding Parameters ◽  
Friction Stir ◽  
Tool Pin Profile ◽  
Tool Pin

Abstract Friction stir welding is a solid state innovative joining technique, widely being used for joining aluminium alloys in aerospace, marine automotive and many other applications of commercial importance. The welding parameters and tool pin profile play a major role in deciding the weld quality. In this paper, an attempt has been made to understand the influences of welding speed and pin profile of the tool on friction stir welded joints of AA6082-T6 alloy. Three different tool pin profiles (tapered cylindrical four flutes, triangular and hexagonal) have been used to fabricate the joints at different welding speeds in the range of 30 to 74 mm/min. Microhardness (HV) and tensile tests performed at room temperature were used to evaluate the mechanical properties of the joints. In order to analyse the microstructural evolution of the material, the weld’s cross-sections were observed optically and SEM observations were made of the fracture surfaces. From this investigation it is found that the hexagonal tool pin profile produces mechanically sound and metallurgically defect free welds compared to other tool pin profiles.

Effect of Friction Stir Welding Parameters on Microstructure and Properties of Welded 5083 Aluminium Alloy

2020 ◽  
Vol 20 (8) ◽  
pp. 5055-5063
Author(s):  
Lixin Hao ◽  
Ruiling Jia ◽  
Xiwei Zhai ◽  
Huixia Zhang ◽  
Jian Hou
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Aluminium Alloy ◽  
Heat Affected Zone ◽  
Intermetallic Phase ◽  
Welding Parameters ◽  
Kelvin Probe ◽  
Friction Stir ◽  
The Difference ◽  
Fsw Parameters

The friction stir welding (FSW) parameters were designed in this study by orthogonal experimental method. The microstructure, mechanical properties and corrosion behavior of corresponding FSW joints of 5083 aluminium alloy (AA5083) were also investigated. Scanning Kelvin probe force microscopy (SKPFM) was employed to study local potential differences on the FSW joint. Results showed that the welding parameters greatly influenced the FSW joint properties of the AA5083. The ratio of rotation speed to welding speed (n/v) mainly affected the mechanical properties of the joint. The tensile strength for the joint was reduced when welded with too large or too small n/v. The hardness of all FSW joints was characterized with similar ‘W-shaped,’ and minimum hardness value appeared on advancing side of the heat affected zone. Different heat input and agitation intensity caused heterogeneous microstructure for the AA5083 FSW joint, which led to differences in passivation properties of weld nugget zone, thermo-mechanically affected zone and heat-affected zone. Susceptibility of the AA5083 FSW joint to pitting corrosion was attributed to the difference of relative potential between the intermetallic phase and Al matrix.

scholarly journals Thermo-mechanical analysis of linear welding stage in friction stir welding - influence of welding parameters

2021 ◽  
pp. 186-186
Author(s):  
Darko Veljic ◽  
Marko Rakin ◽  
Aleksandar Sedmak ◽  
Nenad Radovic ◽  
Bojan Medjo ◽  
...  
Keyword(s):  
Friction Stir Welding ◽  
Heat Generation ◽  
Welding Speed ◽  
Reaction Force ◽  
Material Model ◽  
Element Model ◽  
Welding Parameters ◽  
Al Alloy ◽  
Friction Stir ◽  
Fsw Parameters

The influence of friction stir welding (FSW) parameters on thermo-mechanical behaviour of the material during welding is analysed. An aluminium alloy is considered (Al 2024 T351), and different rotating speed and welding speed are applied. Finite element model consists of the plate (Al alloy), backing plate and welding tool, and it is formed and solved in software package Simulia Abaqus. The influence of the welding conditions on material behaviour is taken into account by application of the Johnson-Cook material model. The rotation of the tool affects the results: if increased, it contributes to an increase of friction-generated heat intensity. The other component of the generated heat, the plastic deformation of the material, is negligibly changed. When the welding speed is increased, the intensity of friction-generated heat decreases, while the heat generation due to plastic deforming increases. Combined, these two effects cause small change of the total heat generation. For the same welded joint length, the plate welded by lower speed will be heated more intensively. The changes of the heat generation influence both the temperature field and reaction force, which are also considered.

scholarly journals Research on the Friction Stir Welding of Sc-Modified AA2519 Extrusion

Metals ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 1024 ◽  
Author(s):  
Robert Kosturek ◽  
Lucjan Śnieżek ◽  
Janusz Torzewski ◽  
Marcin Wachowski
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Base Material ◽  
Stir Zone ◽  
Welding Parameters ◽  
Friction Stir ◽  
Treated Condition ◽  
Heat Treated ◽  
Heat Treated Condition ◽  
Fsw Parameters

The aim of this research was to investigate the effect of friction stir welding (FSW) parameters on microstructure and mechanical properties of Sc-modified AA2519 extrusion joints. The workpiece was welded by FSW in non-heat-treated condition with seven different sets of welding parameters. For each obtained joint macrostructure and microstructure observations were performed. Mechanical properties of joints were investigated using tensile test together with localization of fracture location. Joint efficiencies were established by comparing measured joints tensile strength to the value for base material. The obtained results show that investigated FSW joints of Sc-modified AA2519 in the non-heat-treated condition have joint efficiency within the range 87–95%. In the joints obtained with the lowest ratio of the tool rotation speed to the tool traverse speed, the occurrence of imperfections (voids) localized in the stir zone was reported. Three selected samples were subjected to further investigations consisting microhardness distribution and scanning electron microscopy fractography analysis. As the result of dynamic recrystallization, the microhardness of the base material value of 86 HV0.1 increased to about 110–125 HV0.1 in the stir zone depending on the used welding parameters. Due to lack of the strengthening phase and low strain hardening of used alloy the lack of a significantly softened zone was reported by both microhardness analysis and investigation of the fractured samples.

scholarly journals Microstructure and Mechanical Properties of Friction Stir Welded Joints Between Commercially Pure Copper and Al 6351 Alloy

2017 ◽  
Vol 62 (3) ◽  
pp. 1819-1825
Author(s):  
V.C. Sinha ◽  
S. Kundu ◽  
S. Chatterjee
Keyword(s):  
Mechanical Properties ◽  
Welded Joints ◽  
Rotational Speed ◽  
Pure Copper ◽  
Stir Zone ◽  
Tool Rotational Speed ◽  
Friction Stir ◽  
Commercially Pure ◽  
Microstructure And Mechanical Properties ◽  
Commercially Pure Copper

AbstractIn the present study, the effect of tool rotational speed on microstructure and mechanical properties of friction stir welded joints between commercially pure copper and 6351 Al alloy was carried out in the range of tool rotational speeds of 300-900 rpm in steps of 150 rpm at 30 mm/minutes travel speed. Up to 450 rpm, the interface of the joints is free from intermetallics and Al4Cu9intermetallic has been observed at the stir zone. However, Al4Cu9intermetallic was observed both at the interface and the stir zone at 600 rpm. At 750 and 900 rpm tool rotational speed, the layers of AlCu, Al2Cu3and Al4Cu9intermetallics were observed at the interface and only Al4Cu9intermetallics has been observed in the stir zone. The maximum ultimate tensile strength of ~207 MPa and yield strength of ~168 MPa along with ~6.2% elongation at fracture of the joint have been obtained when processed at 450 rpm tool rotational speed.

scholarly journals Metallurgical and Mechanical Characterization of High-Speed Friction Stir Welded AA 6082-T6 Aluminum Alloy

Materials ◽  
2019 ◽  
Vol 12 (24) ◽  
pp. 4211 ◽  
Author(s):  
Anton Naumov ◽  
Iuliia Morozova ◽  
Evgenii Rylkov ◽  
Aleksei Obrosov ◽  
Fedor Isupov ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Welding Speed ◽  
Welded Joints ◽  
High Speed ◽  
Structural Characteristics ◽  
Tensile Fracture ◽  
Friction Stir ◽  
Microhardness Distribution ◽  
Aluminum Sheets

The objective of this study was to investigate the effect of the high welding speed on the mechanical properties and their relations to microstructural characteristics of butt friction stir welded joints with the use of 6082-T6 aluminum alloy. The aluminum sheets of 2.0 mm thick were friction stir welded at low (conventional FSW) and high welding speeds (HSFSW) of 200 and 2500 mm/min, respectively. The grain size in the nugget zone (NZ) was decreased; the width of the softened region was narrowed down as well as the lowest microhardness value located in the heat-affected zone (HAZ) was enhanced by HSFSW. The increasing welding speed resulted in the higher ultimate tensile strength and lower elongation, but it had a slight influence on the yield strength. The differences in mechanical properties were explained by analysis of microstructural changes and tensile fracture surfaces of the welded joints, supported by the results of the numerical simulation of the temperature distribution and material flow. The fracture of the conventional FSW joint occurred in the HAZ, the weakest weld region, while all HSFSW joints raptured in the NZ. This demonstrated that both structural characteristics and microhardness distribution influenced the actual fracture locations.

Sign in / Sign up

Export Citation Format

Share Document