scholarly journals On Characteristics of Ferritic Steel Determined during the Uniaxial Tensile Test

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3117
Author(s):  
Ihor Dzioba ◽  
Sebastian Lipiec ◽  
Robert Pala ◽  
Piotr Furmanczyk
Keyword(s):  
Tensile Test ◽  
Test Data ◽  
Constitutive Relationship ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Element Analysis ◽  
Material Weakness ◽  
Uniaxial Test ◽  
The Impact ◽  
Tensile Test Data

Tensile uniaxial test is typically used to determine the strength and plasticity of a material. Nominal (engineering) stress-strain relationship is suitable for determining properties when elastic strain dominates (e.g., yield strength, Young’s modulus). For loading conditions where plastic deformation is significant (in front of a crack tip or in a neck), the use of true stress and strain values and the relationship between them are required. Under these conditions, the dependence between the true values of stresses and strains should be treated as a characteristic—a constitutive relationship of the material. This article presents several methodologies to develop a constitutive relationship for S355 steel from tensile test data. The constitutive relationship developed was incorporated into a finite element analysis of the tension test and verified with the measured tensile test data. The method of the constitutive relationship defining takes into account the impact of high plastic strain, the triaxiality stress factor, Lode coefficient, and material weakness due to the formation of microvoids, which leads to obtained correctly results by FEM (finite elements method) calculation. The different variants of constitutive relationships were applied to the FEM loading simulation of the three-point bending SENB (single edge notched bend) specimen to evaluate their applicability to the calculation of mechanical fields in the presence of a crack.

Performance evaluation of HDPE/MWCNT and HDPE/kenaf composites

2019 ◽  
pp. 089270571986827 ◽  
Author(s):  
Nayan Pundhir ◽  
Sunny Zafar ◽  
Himanshu Pathak
Keyword(s):  
Tensile Test ◽  
Strain Rate ◽  
Polymer Composite ◽  
Tensile Modulus ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Compression Moulding ◽  
Multi Walled Carbon Nanotube ◽  
Kenaf Composites ◽  
The Impact

The present work deals with the microwave-assisted compression moulding of high-density polyethylene (HDPE)-based composites. In the present work, 20 wt% of reinforcement in the form of kenaf and multi-walled carbon nanotube (MWCNT) was used to fabricate HDPE/kenaf and HDPE/MWCNT polymer composites. The mechanical characterizations of the microwave-processed composites were carried out in terms of uniaxial tensile test with different strain rate, multistep stress relaxation, flexural and impact test. The uniaxial tensile test revealed that the tensile modulus of microwave-processed four-layered HDPE/kenaf polymer composite was 35.2% higher than that of HDPE/MWCNT polymer composite. The HDPE/MWCNT polymer composite showed a minimum of 1.25 GPa and a maximum of 4.7 GPa of elastic modulus when tested at different strain rate. The impact energy absorbed by the HDPE/kenaf polymer composite (1.055 J) was 81.12% higher than the HDPE/MWCNT polymer composite (0.582 J).

scholarly journals Strength Behaviour of Hot Die Steel with Respect to its Heat Treatment

2020 ◽  
Vol 9 (1) ◽  
pp. 2100-2102
Keyword(s):  
Heat Treatment ◽  
Grain Size ◽  
Tensile Strength ◽  
Tensile Test ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Austenitizing Temperature ◽  
Tempering Temperature ◽  
Die Steel ◽  
The Impact

The surface temperature of hot die steel reaches typically up to 550ºC or above during processes like hot extrusion and casting non-ferrous material. The present paper explores the impact of austenitizing temperature as well as tempering temperature on the tensile strength of hot die steel. Heat treatment is done at three different austenitizing temperatures of 1010ºC, 1030ºC, and 1050ºC, followed by tempering done at two different temperatures of 540ºC and 580°C. Tempering is done twice for two hours. Metallographic grinding, polishing, and then etching using 2% Nital is done to investigate the microstructure of hot die steel with respect to its heat treatment. It is found that the grain size of hot die steel increases with an increase in austenitizing temperature. The impact on tensile strength of hot die steel for its heat treatment is examined by conducting the uniaxial tensile test to fracture. And investigation of the morphology of the fracture surface produced after the tensile test is done. It was found that hot die steel with large grain size exhibits lesser tensile strength. Whereas, the one having smaller grain has higher tensile strength that is found to be in accordance with the Hall-Patch equation

scholarly journals Corrosion Behaviour of Multiaxial Compressed AlMgSi alloy

2021 ◽  
Vol 71 (03) ◽  
pp. 359-364
Author(s):  
Abir Roy ◽  
Abhishek Kumar
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Test ◽  
Electron Backscatter Diffraction ◽  
Corrosion Behaviour ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Average Grain Size ◽  
The Impact ◽  
Almgsi Alloy

In the present study, AlMgSi alloy was processed through multi-axial compression (MAC) to produce ultrafine-grained microstructure at room temperature. The AlMgSi alloys are widely used in automobile industries for making cylinder heads and brake disks etc. MAC was performed up to three cycles and showed improvement in mechanical properties. The impact of different strain levels upon microstructure changes is investigated using electron backscatter diffraction (EBSD). The average grain size reduced from an initial average grain size of ~ 124 to ~ 3 μm after completion of three cycles of MAC processing. Samples were tested for mechanical properties using uniaxial tensile test, hardness measurements, and corrosion. Tensile test results show a considerable increase in yield strength from ~90 MPa to ~249 MPa after 3 cycles of MAC. The average hardness value increased from 52 VHN to 90 VHN after 3 cycles of MAC. The corrosion resistance of MAC processed samples was found to decrease in comparison to solution-treated samples.

scholarly journals The Use of Neural Networks in the Analysis of Dual Adhesive Single Lap Joints Subjected to Uniaxial Tensile Test

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 419
Author(s):  
Jakub Gajewski ◽  
Przemysław Golewski ◽  
Tomasz Sadowski
Keyword(s):  
Neural Networks ◽  
Numerical Modeling ◽  
Tensile Test ◽  
Adhesive Bonding ◽  
Lap Joints ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Single Lap Joints ◽  
Bonded Joint ◽  
The Impact

Adhesive bonding are becoming increasingly important in civil and mechanical engineering, in the field of mobile applications such as aircraft or automotive. Adhesive joints offer many advantages such as low weight, uniform stress distribution, vibration damping properties or the possibility of joining different materials. The paper presents the results of numerical modeling and the use of neural networks in the analysis of dual adhesive single-lap joints subjected to a uniaxial tensile test. The dual adhesive joint was created through the use of adhesives with various parameters in terms of stiffness and strength. In the axis of the overlap, there was a point bonded joint characterized by greater stiffness and strength, and on the outside, there was a bonded joint limited by the edges of the overlap and characterized by lower stiffness and strength. It is an innovative solution for joining technology and the influence of such parameters as the thickness of one of the adherends, the radius of the point bonded joint and the material parameters of both adhesive layers were analyzed. The joint is characterized by a two-stage degradation process, i.e., after the damage of the rigid adhesive, the flexible adhesive ensures the integrity of the entire joint. For numerical modeling, the Finite Element Method (FEM) and cohesive elements was used, which served as input data to an Artificial Neural Network (ANN). The applied approach allowed the impact of individual parameters on the maximum force, initiation energy, and fracture energy to be studied.

Developing Uniaxial Tensile Test as an Alternate Method for Thermo Mechanical Process Evaluation

2011 ◽  
Vol 383-390 ◽  
pp. 5404-5408
Author(s):  
Dedi Priadi ◽  
Richard A. M. Napitupulu ◽  
Eddy S. Siradj
Keyword(s):  
Tensile Test ◽  
Plane Strain ◽  
Testing Machine ◽  
Forming Limit Diagram ◽  
Grain Structure ◽  
Forming Limit ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Mechanical Process ◽  
Uniaxial Test

The alternate method for evaluating the thermo mechanical process has been developed. Small attention has been paid to the mechanism of plastic deformation especially plane strain analysis. Modified the specimen geometry and using uniaxial tensile test was done to view the process. Experimental results show that the forming limit diagram as one of the formability characteristic can be view the plane strain condition that present on the thermo mechanical process. The microstructure result shows that there is a similar grain structure between hot tensile test and hot rolling results as one of thermo mechanical process method. It was concluded that the uniaxial test using universal testing machine could be done to evaluate the thermo mechanical process.

Design resistance of helical seam pipe columns with limited tensile test data

2021 ◽  
Vol 183 ◽  
pp. 106724
Author(s):  
Won-Hee Kang ◽  
Stephen J. Hicks ◽  
Brian Uy ◽  
Farhad Aslani
Keyword(s):  
Tensile Test ◽  
Test Data ◽  
Design Resistance ◽  
Tensile Test Data

Constitutive Modeling of Biaxial Mechanical Response of Arteries Subjected to Gradual Elastin Degradation

2013 ◽  
Author(s):  
Shahrokh Zeinali-Davarani ◽  
Ming-Jay Chow ◽  
Raphaël Turcotte ◽  
Katherine Yanhang Zhang
Keyword(s):  
Tensile Test ◽  
Mechanical Behavior ◽  
Test Data ◽  
Constitutive Modeling ◽  
Mechanical Response ◽  
Collagen Fibers ◽  
Biaxial Tensile Test ◽  
Elastin Degradation ◽  
Adaptive Processes ◽  
Tensile Test Data

The passive mechanical response of arteries is believed to be mainly dominated by elastin and collagen fibers. Many arterial diseases are accompanied by significant changes in quantity and as well as the microstructure of these constituents due to the mechanical and biological adaptive processes. In this study we focus on the biaxial tensile test data of elastase-treated porcine aortic tissues [1]. We study the mechanical behavior of aortic tissues under gradual elastin degradation through constitutive modeling and associate the mechanical response with the microstructure of collagen observed in the microscopic images of fresh and digested tissues.

Sign in / Sign up

Export Citation Format

Share Document