scholarly journals Centrifugal Compressor Stall Control by the Application of Engineered Surface Roughness on Diffuser Shroud Using Numerical Simulations

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2033
Author(s):  
Amjid Khan ◽  
Muhammad Irfan ◽  
Usama Muhammad Niazi ◽  
Imran Shah ◽  
Stanislaw Legutko ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Centrifugal Compressor ◽  
Control Method ◽  
Flow Instability ◽  
Passive Flow Control ◽  
Passive Flow ◽  
Low Mass

Downsizing in engine size is pushing the automotive industry to operate compressors at low mass flow rate. However, the operation of turbocharger centrifugal compressor at low mass flow rate leads to fluid flow instabilities such as stall. To reduce flow instability, surface roughness is employed as a passive flow control method. This paper evaluates the effect of surface roughness on a turbocharger centrifugal compressor performance. A realistic validation of SRV2-O compressor stage designed and developed by German Aerospace Center (DLR) is achieved from comparison with the experimental data. In the first part, numerical simulations have been performed from stall to choke to study the overall performance variation at design conditions: 2.55 kg/s mass flow rate and rotational speed of 50,000 rpm. In second part, surface roughness of magnitude range 0–200 μm has been applied on the diffuser shroud to control flow instability. It was found that completely rough regime showed effective quantitative results in controlling stall phenomena, which results in increases of operating range from 16% to 18% and stall margin from 5.62% to 7.98%. Surface roughness as a passive flow control method to reduce flow instability in the diffuser section is the novelty of this research. Keeping in view the effects of surface roughness, it will help the turbocharger manufacturers to reduce the flow instabilities in the compressor with ease and improve the overall performance.

Numerical Investigation of Diffuser Rotating Stall and System Instability in a Centrifugal Compressor With Vaned Diffuser

2018 ◽  
Author(s):  
Yang Zhao ◽  
Guang Xi ◽  
Jiayi Zhao
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Centrifugal Compressor ◽  
Flow Instability ◽  
Leading Edge ◽  
Rotating Stall ◽  
Vaned Diffuser ◽  
Corner Separation ◽  
Lumped Parameter

The operating range of a centrifugal compressor is often limited by the occurrence of the flow instability, such as diffuser rotating stall or system surge. In the paper, the unsteady numerical simulations are performed on a low-speed centrifugal compressor to investigate the characteristic of the rotating stall in the vaned diffuser. And also, the developed model of lumped parameter is used to predict the system instability. The flow field in the diffuser is firstly investigated at near stall condition. It is found that the leading-edge vortex and the secondary flow induce the hub-corner separation at the suction side of the diffuser blade. When the mass flow rate is reduced gradually, the fore part of the volute turns to act as a diffuser from a nozzle. Under the influence of the asymmetry induced by the volute, the hub-corner separation firstly develops into rotating stall in the passage with the lowest mass flow rate when at critical stall point. And then the diffuser rotating stall propagates along the circumferential direction at about 7% of the impeller speed. And also, the model of lumped parameter considering the effect of rotating stall is developed to analyze the system instability of mild surge. The predicted vibration frequency is within 5.8% of the measurement and the predicted transient process in mild surge matches well with the measurement. With different volume of the compressed air, the transient compressor characteristic tends to be stabilized or oscillates in a cycle along the counter-clockwise with different magnitude.

Unsteady Responses of the Impeller of a Centrifugal Compressor Exposed to Pulsating Backpressure

2018 ◽  
Vol 141 (4) ◽  
Author(s):  
Mengying Shu ◽  
Mingyang Yang ◽  
Ricardo F. Martinez-Botas ◽  
Kangyao Deng ◽  
Lei Shi
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Centrifugal Compressor ◽  
Combustion Engine ◽  
Fluid Dynamic ◽  
Flow Behavior ◽  
Three Dimensional ◽  
Intake Manifold ◽  
Unsteady Simulation

The flow in intake manifold of a heavily downsized internal combustion engine has increased levels of unsteadiness due to the reduction of cylinder number and manifold arrangement. The turbocharger compressor is thus exposed to significant pulsating backpressure. This paper studies the response of a centrifugal compressor to this unsteadiness using an experimentally validated numerical method. A computational fluid dynamic (CFD) model with the volute and impeller is established and validated by experimental measurements. Following this, an unsteady three-dimensional (3D) simulation is conducted on a single passage imposed by the pulsating backpressure conditions, which are obtained by one-dimensional (1D) unsteady simulation. The performance of the rotor passage deviates from the steady performance and a hysteresis loop, which encapsulates the steady condition, is formed. Moreover, the unsteadiness of the impeller performance is enhanced as the mass flow rate reduces. The pulsating performance and flow structures near stall are more favorable than those seen at constant backpressure. The flow behavior at points with the same instantaneous mass flow rate is substantially different at different time locations on the pulse. The flow in the impeller is determined by not only the instantaneous boundary condition but also by the evolution history of flow field. This study provides insights in the influence of pulsating backpressure on compressor performance in actual engine situations, from which better turbo-engine matching might be benefited.

Computational Fluid Dynamics Performance Estimation of Turbo Booster Vacuum Pump

2003 ◽  
Vol 125 (3) ◽  
pp. 586-589 ◽  
Author(s):  
H.-P. Cheng ◽  
C.-J. Chen , ◽  
P.-W. Cheng ,
Keyword(s):  
Fluid Dynamics ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Vacuum Pump ◽  
Performance Estimation ◽  
High Mass ◽  
Rotor Speed ◽  
Low Mass ◽  
Pump Inlet

The CFD performance estimation of turbo booster vacuum pump shows the axial vortex and back flow is evident when the mass flow rate is increased. The pressure is increased from the pump inlet to the outlet for the low mass flow rate cases. But for high mass flow rate cases, the pressure is increased until the region near the end of the rotor then decreased. The calculated inlet pressure, compression ratio, and pumping speed is increased, decreased, and decreased, respectively, when the mass flow rate is increased. The pumping speed is increased when the rotor speed is increased.

Numerical Performance and Flow Field Study of Centrifugal Compressor With Supercritical Carbon-Dioxide (SCO2)

2019 ◽  
Author(s):  
Hemant Kumar ◽  
Chetan S. Mistry
Keyword(s):  
Carbon Dioxide ◽  
Thermodynamic Properties ◽  
Critical Point ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Centrifugal Compressor ◽  
Numerical Study ◽  
Pressure Ratio ◽  
Compressor Inlet

Abstract The Supercritical carbon-dioxide Brayton cycle main attraction is due to the Supercritical characteristic of the working fluid, carbon-dioxide (SCO2). Some of the advantages of using SCO2 are relatively low turbine inlet temperature, the compression work will be low, and the system will be compact due to the variation of thermodynamic properties (like density, and specific heat ratio) of SCO2 near the critical point. SCO2 behave more like liquid when its state is near the critical point (Total Pressure = 7.39 MPa, Total Temperature = 305 K), operating compressor inlet near critical point can minimize compression work. For present study the centrifugal compressor was designed to operate at 75,000 rpm with pressure ratio (P.R) = 1.8 and mass flow rate = 3.53 kg/s as available from Sandai report. Meanline design for centrifugal compressor with SCO2 properties was done. The blade geometry was developed using commercial CAD Ansys Bladegen. The flow domain was meshed using Ansys TurboGrid. ANSYS CFX was used as a solver for present numerical study. The thermodynamic properties of SCO2 were imported from the ANSYS flow material library using SCO2.RPG [NIST thermal physics properties of fluid system]. In order to ensure the change in flow physics the mesh independence study was also conducted. The present paper discuss about the performance and flow field study targeting different mass flow rates as exit boundary condition. The comparison of overall performance (Pressure Ratio, the Blade loading, Stage efficiency and Density variation) was done with three different mass flow rates. The designed and simulated centrifugal compressor meets the designed pressure rise requirement. The variation of mass flow rate on performance of centrifugal compressor was tend to be similar to conventional centrifugal compressor. The paper discusses about the effect of variation in density, specific heat ratio and pressure of SCO2 with different mass flow outlet condition. The performance map of numerical study were validated with experiment results and found in good agreement with experimental results. The change in flow properties within the rotor flow passage are found to be interesting and very informative for future such centrifugal compressor design for special application of SCO2 Brayton cycle. 80% mass flow rate has given better results in terms of aerodynamic performance. Abrupt change in thermodynamic properties was observed near impeller inlet region. Strong density variations are observed at compressor inlet.

Centrifugal Compressor Performance Prediction Using Gaussian Process Regression and Artificial Neural Networks

2019 ◽  
Author(s):  
Pau Cutrina Vilalta ◽  
Hui Wan ◽  
Soumya S. Patnaik
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Centrifugal Compressor ◽  
Rotational Speed ◽  
Data Augmentation ◽  
Pressure Ratio ◽  
Gaussian Process Regression ◽  
Compressor Performance ◽  
Artificial Neural

Abstract In this paper, we use various regression models and Artificial Neural Network (ANN) to predict the centrifugal compressor performance map. Particularly, we study the accuracy and efficiency of Gaussian Process Regression (GPR) and Artificial Neural Networks in modelling the pressure ratio, given the mass flow rate and rotational speed of a centrifugal compressor. Preliminary results show that both GPR and ANN can predict the compressor performance map well, for both interpolation and extrapolation. We also study the data augmentation and data minimzation effects using the GPR. Due to the inherent pressure ratio data distribution in mass-flow-rate and rotational-speed space, data augmentation in the rotational speed is more effective to improve the ANN performance than the mass flow rate data augmentation.

Effect of surface roughness on the mass flow rate predictions for adiabatic capillary tubes

2020 ◽  
Vol 118 ◽  
pp. 269-278 ◽  
Author(s):  
Thiago Torres Martins Rocha ◽  
Cleison Henrique de Paula ◽  
Vinícius Melo Cangussu ◽  
Antônio Augusto Torres Maia ◽  
Raphael Nunes de Oliveira
Keyword(s):  
Surface Roughness ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Capillary Tubes ◽  
Effect Of Surface

Effect of Process Parameters on Depth of Penetration & Surface Roughness in Abrasive Waterjet Cutting of Copper

2019 ◽  
Vol 895 ◽  
pp. 301-306
Author(s):  
Keshav Kashyap ◽  
S. Srinivas
Keyword(s):  
Surface Roughness ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Process Parameters ◽  
Flow Rate ◽  
Traverse Speed ◽  
High Water ◽  
Water Jet ◽  
Abrasive Waterjet ◽  
Depth Of Penetration

This study evaluates the effect of process parameters on depth of penetration and surface roughness in abrasive waterjet (AWJ) cutting of copper. Full factorial experiments are carried out on trapezoidal blocks for each of the three abrasive particle sizes used. Experimental parameters - abrasive mass flow rate, water jet pressure and traverse speed are varied at three levels. Main effects and contributions of process parameters to depth of penetration and surface roughness is calculated. From the data, it is observed that, high abrasive mass flow rate, high water jet pressure and low traverse speed resulted in higher depth of penetration and a high abrasive mass flow rate, high water jet pressure and low traverse speed resulted in lesser Ra value. Using experimental data a statistical model for predicting depth of penetration & surface roughness is developed. Error between experimental and statistical values are compared to validate the statistical model. The maximum DOP of 49.32mm was observed at AMFR=405.4 g/min, P=300 MPa, TS=60 mm/min, MS=60 Mesh and minimum DOP of 4.27mm was observed at AMFR=200 g/min, P=100 MPa, TS=90 mm/min, MS=80 Mesh.

The Liftoff Properties of Dimethyl Ether Jet Diffusion Flames With Preheating

2013 ◽  
Author(s):  
Jie Zhou ◽  
Yuhua Ai ◽  
Wenjun Kong
Keyword(s):  
Ambient Temperature ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Diffusion Flames ◽  
Thermal Buoyancy ◽  
Jet Diffusion Flames ◽  
Lifted Flames ◽  
Low Mass ◽  
Jet Velocity

Liftoff properties of DME laminar axisymmetric diffusion flames were investigated experimentally with emphasis on the preheating effects. At room temperature, DME presented a different liftoff phenomenon from the non-oxygenated hydrocarbon fuels. It could not be lifted off directly by increasing the jet velocity except for far field ignition at relatively low mass flow rate. When fuel and dilution were preheated, the DME flame could be lifted off directly by increasing the jet velocity. The range of the mass flow rate of stabilized DME liftoff flames became much narrower and the liftoff height became much smaller at fuel preheating than that at ambient temperature. With the increase of the jet temperature, the DME liftoff flames exhibited as one of the following three types: stationary lifted flames, stable oscillating lifted flames and unstable oscillating lifted flames. Stationary lifted flames existed when the initial temperature was relatively low (less than 350 K). Stable oscillating lifted flames were observed at relatively high preheated temperature (about 350 K ∼ 750 K), and the trajectory of the liftoff flame base was nearly sinusoidal. Both the oscillating frequency and amplitude increased with the preheating temperature. The oscillating lifted flames were caused by thermal buoyancy effect, inertia and the instability in the inner flow. When the jet temperature exceeded 750 K, the oscillating lifted flames became unstable and easily to be blown out. The flame base of the stabilized DME liftoff flame had a tribrachial structure at both ambient temperature and elevated temperature.

Experimental Investigation of Flow Instability in a Supersonic Inlet

2010 ◽  
Author(s):  
Mohammad Reza Soltani ◽  
Mohammad Farahani
Keyword(s):  
Mach Number ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Flow Instability ◽  
Wind Tunnel Test ◽  
External Flow ◽  
Pressure Data ◽  
Supersonic Inlet ◽  
Shock Oscillation

An extensive wind tunnel test series were conducted on an axisymmetric supersonic inlet. The model was tested at Mach numbers from 1.8 to 2.2 and at different values of mass flow rate. Shadowgraph flow visualization was used to capture the external shock structure in front of the inlet. The goal of this study is to find out the general characteristics of the inlet buzz. Frequencies of the buzz have been achieved from the analysis of the pressure data as well as the shadowgraph pictures. The amplitude of the shock waves motion has been measured from the visualization pictures too. In the some large value of mass flow rate, the frequency of shock oscillation increased versus Mach number. Also in each Mach number due to the mass flow rate decrement, the buzz frequency decreases and its amplitude increases conversely. Also buzz instability affects the external flow by the same frequency of the internal one.

Sign in / Sign up

Export Citation Format

Share Document