scholarly journals Influence of Cement Replacement with Fly Ash and Ground Sand with Different Fineness on Alkali-Silica Reaction of Mortar

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1528
Author(s):  
Suwat Ramjan ◽  
Weerachart Tangchirapat ◽  
Chai Jaturapitakkul ◽  
Cheah Chee Ban ◽  
Peerapong Jitsangiam ◽  
...  
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Ordinary Portland Cement ◽  
Partial Substitution ◽  
Alkali Silica Reaction ◽  
Inert Material ◽  
Fly Ashes ◽  
River Sand ◽  
Concrete Materials

The alkali-silica reaction (ASR) is an important consideration in ensuring the long-term durability of concrete materials, especially for those containing reactive aggregates. Although fly ash (FA) has proven to be useful in preventing ASR expansion, the filler effect and the effect of FA fineness on ASR expansion are not well defined in the present literature. Hence, this study aimed to examine the effects of the filler and fineness of FA on ASR mortar expansion. FAs with two different finenesses were used to substitute ordinary Portland cement (OPC) at 20% by weight of binder. River sand (RS) with the same fineness as the FA was also used to replace OPC at the same rate as FA. The replacement of OPC with RS (an inert material) was carried out to observe the filler effect of FA on ASR. The results showed that FA and RS provided lower ASR expansions compared with the control mortar. Fine and coarse fly ashes in this study had almost the same effectiveness in mitigating the ASR expansion of the mortars. For the filler effect, smaller particles of RS had more influence on the ASR reduction than RS with coarser particles. A significant mitigation of the ASR expansion was obtained by decreasing the OPC content in the mortar mixture through its partial substitution with FA and RS.

Evolution of Lime and Microstructural Development In Fly Ash-Portland Cement Systems

1989 ◽  
Vol 178 ◽  
Author(s):  
Joseph A. Larbi ◽  
Jan M. Bijen
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Dilution Effect ◽  
Pozzolanic Reaction ◽  
Microstructural Development ◽  
Inert Material ◽  
Interfacial Region ◽  
Interfacial Zone ◽  
Fly Ashes ◽  
Intimate Contact

AbstractThe evolution and distribution of calcium hydroxide, CH, and the development of microstructure during the hydration of three low-calcium fly ash-Portland cement blends with water-solids ratio (w/s) of 0.40 have been investigated. During the first month of hydration, the CH content of the blends was found to be relatively higher than the plain mix, if a dilution effect due to replacement of cement by an inert material is taken into account. After 28 days of hydration the CH content in the blends began to decrease. SEM observations of specimens revealed the occurrence of large, well-crystallized CH plates in intimate contact with some of the fly ash particles at younger ages and even after six months of aging. The study also showed that the chemistry of the pore solution in contact with the hydrating cement system and the characteristics of the fly ashes, such as the glass content and the fineness of the ash particles seem to exert major influences on the rate of evolution of CH in the fly ash blends. Semi-quantitative X-ray diffraction analyses performed on specimens cast against polypropylene plastic plates used to “model coarse aggregates” showed reduction in the thickness of the interfacial zone for the fly ash-Portland cement pastes from about 60μm to less than 15μm within one month of hydration. In the case of the plain Portland cement paste no significant change was observed. The degree of orientation of CH crystals within the interfacial region also was significantly affected by the fly ashes, although by this age of hydration the CH data showed little or no evidence of pozzolanic reaction.

scholarly journals Strength Development and Elemental Distribution of Dolomite/Fly Ash Geopolymer Composite under Elevated Temperature

Materials ◽  
2020 ◽  
Vol 13 (4) ◽  
pp. 1015 ◽  
Author(s):  
Emy Aizat Azimi ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
Petrica Vizureanu ◽  
Mohd Arif Anuar Mohd Salleh ◽  
Andrei Victor Sandu ◽  
...  
Keyword(s):  
Elevated Temperature ◽  
Fly Ash ◽  
Portland Cement ◽  
Ordinary Portland Cement ◽  
Raw Materials ◽  
Liquid Sodium ◽  
Strength Development ◽  
Elemental Distribution ◽  
Distribution Analysis ◽  
Geopolymer Composites

A geopolymer has been reckoned as a rising technology with huge potential for application across the globe. Dolomite refers to a material that can be used raw in producing geopolymers. Nevertheless, dolomite has slow strength development due to its low reactivity as a geopolymer. In this study, dolomite/fly ash (DFA) geopolymer composites were produced with dolomite, fly ash, sodium hydroxide, and liquid sodium silicate. A compression test was carried out on DFA geopolymers to determine the strength of the composite, while a synchrotron Micro-Xray Fluorescence (Micro-XRF) test was performed to assess the elemental distribution in the geopolymer composite. The temperature applied in this study generated promising properties of DFA geopolymers, especially in strength, which displayed increments up to 74.48 MPa as the optimum value. Heat seemed to enhance the strength development of DFA geopolymer composites. The elemental distribution analysis revealed exceptional outcomes for the composites, particularly exposure up to 400 °C, which signified the homogeneity of the DFA composites. Temperatures exceeding 400 °C accelerated the strength development, thus increasing the strength of the DFA composites. This appears to be unique because the strength of ordinary Portland Cement (OPC) and other geopolymers composed of other raw materials is typically either maintained or decreases due to increased heat.

A trial construction of high durability railway viaducts with local aggregates

2019 ◽  
Author(s):  
Kotaro Kawamura ◽  
Joe Takemura ◽  
Shigenobu Iguchi ◽  
Tsutomu Yoshida ◽  
Masashi Kobayashi
Keyword(s):  
Fly Ash ◽  
Side Effects ◽  
Portland Cement ◽  
Ordinary Portland Cement ◽  
The Other ◽  
Strength Concrete ◽  
High Durability ◽  
Sound Barrier ◽  
Early Strength ◽  
Structural Measure

<p>We are carrying out a construction project of new railroad viaducts. These new railroad viaducts are constructing using about 110,000 m<span>3</span> volume concrete. In this construction place, it is difficult for us to get low ASR-reactive aggregates and it is expected to be supplied with snowmelt water on the viaducts in winter. Then we tested ASR-reactive these local aggregates and found an effective mixed ratio of fly-ash is 20% of cement. On the other hand, various side effects were also expected by using fly-ash. For example, initial cracking due to contraction, early strength concrete, bleeding, etc. Therefore, we repeated various tests and examined and carried out a method that could ensure the same construction method and quality as when using ordinary Portland cement, even with fly-ash. Also, we adopted a structure that is unlikely to be affected by rainwater as a structural measure. For example, the entire adoption of a ramen type viaduct that has eliminated bearings, adoption of FRP sound barrier, etc. Then we made it possible to build highly durable railway viaducts by these various measures of materials and structures.</p>

Low Cement/High Fly Ash Concretes: Their Properties and Response to Chemical Admixtures

1987 ◽  
Vol 113 ◽  
Author(s):  
V. H. Dodson
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Calcium Hydroxide ◽  
Pozzolanic Reaction ◽  
Portland Cement Concrete ◽  
Cement Concrete ◽  
Fly Ashes ◽  
Chemical Admixtures ◽  
Reaction With Water

ABSTRACTIn practice, the amount of fly ash added to portland cement concrete varies depending upon the desired end properties of the concrete. Generally, when a given portland cement concrete is redesigned to include fly ash, between 10 and 50% of the cement is replaced by a volume of fly ash equal to that of the cement. Sometimes as much as twice the volume of the cement replaced, although 45.4 kg (100 lbs) of cement will only produce enough calcium hydroxide during its reaction with water to react with about 9 kg (20 lbs) of a typical fly ash. The combination of large amounts of certain fly ashes with small amounts of portland cement in concrete has been found to produce surprisingly high compressive strengths, which cannot be accounted for by the conventional “pozzolanic reaction”. Ratios of cement to fly ash as high as 1:15 by weight can produce compressive strengths of 20.7 MPa (3,000 psi) at I day and over 41.4 MPa (6,000 psi) at 28 days. Methods of identifying these “hyperactive” fly ashes along with some of the startling results, with and without chemical admixtures are described.

scholarly journals Durability of blended cement against sodium sulphate attack and alkali-silica reaction

2021 ◽  
Author(s):  
Giri Raj Adhikari
Keyword(s):  
Fly Ash ◽  
Silica Fume ◽  
Alkali Silica Reaction ◽  
Sulphate Attack ◽  
Ternary Blends ◽  
Replacement Level ◽  
Fly Ashes ◽  
Study Results ◽  
High Calcium ◽  
High Calcium Fly Ash

Blended cements were studied for their efficacy against sulphate attack and alkali-silica reaction using six different types of fly ashes, a slag, a silica fume and four types of General Use Portland cement of different alkalinity. The study results showed that low calcium fly ash, silica fume and ground granulated blast furnace slag enhanced the sulphate resistance of cement with increased efficacy with the increase in the replacement level. However, slag and silica fume, especially at low replacement levels, exhibited increased rate of expansion beyond the age of 78 weeks. On the contrary, high calcium fly ashes showed reduced resistance to sulphate attack with no clear trend between the replacement level and expansion. Ternary blends consisting of silica fume, particulary in the amount of 5%, high calcium fly ashes and General Use (GU) cement provided high sulphate resistance, which was attributable to reduced permeability. In the same way, some of ternary blends consisting of slag, high calcium fly ash and GU cement improved sulphate resistance. Pre-blending optimum amount of gypsum with high calcium fly ash enhanced the latter's resistance to sulphate attack by producing more ettringite at the early stage of hydration. In the context of alkali-silica reaction permeability was found to be a contributing factor to the results of the accelerated mortar bar test. High-alkali, high-calcium fly ash was found to worsen the alkali silica reaction when used in concrete containing some reactive aggregates. Ternary blend of slag with high calcium fly ash was found to produce promising results in terms of counteracting alkali-silica reaction.

High Performance Concrete with Ternary Binders

2018 ◽  
Vol 761 ◽  
pp. 120-123 ◽  
Author(s):  
Vlastimil Bílek ◽  
David Pytlík ◽  
Marketa Bambuchova
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Silica Fume ◽  
High Performance ◽  
Ordinary Portland Cement ◽  
High Performance Concrete ◽  
Fresh Concrete ◽  
Binder Ratio ◽  
Water To Binder Ratio ◽  
Condensed Silica Fume

Use a ternary binder for production of a high performance concrete with a compressive strengths between 120 and 170 MPa is presented. The water to binder ratio of the concrete is 0.225 and the binder is composed of Ordinary Portland Cement (OPC), condensed silica fume (CSF), ground limestone (L), fly ash (FA) and metakaoline (MK). The dosage of (M + CSF) is kept at a constant level for a better workability of fresh concrete. Different workability, flexural and compressive strengths were obtained for concretes with a constant cement and a metakaoline dosage, and for a constant dosage (FA + L) but a different ratio FA / L. An optimum composition was found and concretes for other tests were designed using this composition.

Sign in / Sign up

Export Citation Format

Share Document