scholarly journals Experimental Study of High Performance Synchronous Grouting Materials Prepared with Clay

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1362
Author(s):  
Ying Cui ◽  
Zhongsheng Tan
Keyword(s):  
Epoxy Resin ◽  
High Performance ◽  
Cement Hydration ◽  
High Energy ◽  
Utilization Rate ◽  
Test Results ◽  
Shield Tunneling ◽  
Red Clay ◽  
Grouting Material ◽  
Grouting Materials

Shield construction discharges a large amount of soil and muck. The utilization of discharged soil of shield always has high energy consumption and a low utilization rate. Meanwhile, synchronous grouting is a key process for shield tunneling. The current studies show that the synchronous grouting materials applied now generally have the problem of mismatching among filling property, fluidity, and consolidation strength. In order to study the feasibility of using the excavated soil produced by shield construction in clay stratum as synchronous grouting material, high performance synchronous grouting material was studied by taking red clay as an example, modified by epoxy resin. The fluidity, stability, and strength were measured to evaluate performance of the grout. Material test results show that the addition of waterborne epoxy resin decreases density, improves the stability, the rate of stone, and the toughness of the grouting concretion. Finally, X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM) were measured to analyze the cementitious mechanism of the grout, test results demonstrated that cement hydration and curing reaction of epoxy resin happened in the grout, the formed polymer film filled the voids in the mixture and effectively bound cement hydration gel and clay particles together.

Experimental Research on the Engineering Properties of Foam-Improved Red Clay Soil

2011 ◽  
Vol 261-263 ◽  
pp. 1831-1835
Author(s):  
Guo Gang Qiao ◽  
Da Jun Yuan ◽  
Bo Liu
Keyword(s):  
Experimental Research ◽  
Clay Soil ◽  
Soil Improvement ◽  
Engineering Properties ◽  
Screw Conveyor ◽  
Test Results ◽  
X Ray Diffraction ◽  
Shield Tunneling ◽  
Red Clay ◽  
Improvement Measures

Red clay soil is widely distributed in south China, the microstructure of red clay soil was studied applying scanning electron microscopy (SEM), and the X-ray diffraction analysis (XRD) test found that a large number of swelling inducing minerals, for example, montmorillonite, illite-montmorillonite or chlorite-smectite were contained in the red clay soil. Shield tunneling in this kind of stratum is prone to arising “cake” and “arch” phenomena and it prone to lead screw conveyor device unsmooth dumping, so soil improvement measures must be taken. Foam as the most advanced soil conditioner has been widely used in shield construction. Using self-developed foam agent, experimental research on foam conditioning red clay soil was carried out, test results show that foam can not only significantly reduce the soil shear strength, but also can greatly enhance the soil's compressibility and fluidity, which is significant for the smooth dumping and excavation face stability maintenance.

Research on Multivariate Composite Super early Strength Grouting Materials

2013 ◽  
Vol 477-478 ◽  
pp. 990-995
Author(s):  
Xiao Ping Zhang ◽  
Chang Zheng Sun ◽  
Tong Feng Zhao
Keyword(s):  
Compressive Strength ◽  
High Performance ◽  
Ordinary Portland Cement ◽  
High Alumina ◽  
Flow Ratio ◽  
Initial Flow ◽  
Growth Structure ◽  
Grouting Material ◽  
Early Strength ◽  
Grouting Materials

Super early strength high performance grouting material was produced using high alumina cement, ordinary portland cement, gypsum and silica fume. The different glue sand ratio and the cement sand ratio 1.0 mix microstructure were studied systematically. The results showed that the system with a variety of admixture using hingh mortar ratio can be prepared for the initial flow ratio greater than 325{mm},, 30min flow greater than 280{mm}, 2h compressive strength 34.80{MPa}, 24h bending over 13.82{MPa}, 28d compressive strength greater than 99.90{MPa}, 28d compressive strength greater than 56d compressive strength. The system of early SEM microstructures showed good crystal growth, structure compact.

scholarly journals Study on Rheological Behavior and Surface Properties of Epoxy Resin Chemical Grouting Material Considering Time Variation

Materials ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3277
Author(s):  
Zhenhua Su ◽  
Zaiqin Wang ◽  
Da Zhang ◽  
Tao Wei
Keyword(s):  
Epoxy Resin ◽  
Epoxy Resins ◽  
Time Varying ◽  
Construction Process ◽  
Chemical Grouting ◽  
Grouting Material ◽  
Viscosity Variation ◽  
Grouting Materials ◽  
The Mathematical Model ◽  
Main Factor

Epoxy resins are widely used for repairing cracks in stone, mortar and masonry. A main factor that influences the grouting quality is the permeability of grout. However, the permeability will deteriorate over time because of the reaction of chemical grouting materials, which will greatly affect the results of grouting. To the best of our knowledge, there are few reports that focus on the time-varying properties of viscosity and affinity of epoxy resins grouting material. In this paper, we investigate the changing rules of viscosity and affinity with time by studying the viscosity, surface tension and contact angle of the epoxy grouting material. We establish the mathematical model for the time-dependent properties of CW epoxy resin on viscosity and affinity with experimental verification. Moreover, we make a detailed discussion on the modeling of viscosity variation considering both time and temperature. The results show important guiding significance and application value for judging the grout irrigability in the construction process.

Efficient Co-Harvesting of Solar Energy and Low-Grade Heat by Molecular Photoswitches for High Energy Density, Long-Term Stable Solar Thermal Battery

2019 ◽  
Author(s):  
Zhao-Yang Zhang ◽  
Tao LI
Keyword(s):  
Energy Density ◽  
Solar Energy ◽  
High Performance ◽  
High Energy ◽  
Solar Thermal ◽  
High Energy Density ◽  
Low Grade ◽  
Thermal Battery ◽  
Low Grade Heat

Solar energy and ambient heat are two inexhaustible energy sources for addressing the global challenge of energy and sustainability. Solar thermal battery based on molecular switches that can store solar energy and release it as heat has recently attracted great interest, but its development is severely limited by both low energy density and short storage stability. On the other hand, the efficient recovery and upgrading of low-grade heat, especially that of the ambient heat, has been a great challenge. Here we report that solar energy and ambient heat can be simultaneously harvested and stored, which is enabled by room-temperature photochemical crystal-to-liquid transitions of small-molecule photoswitches. The two forms of energy are released together to produce high-temperature heat during the reverse photochemical phase change. This strategy, combined with molecular design, provides high energy density of 320-370 J/g and long-term storage stability (half-life of about 3 months). On this basis, we fabricate high-performance, flexible film devices of solar thermal battery, which can be readily recharged at room temperature with good cycling ability, show fast rate of heat release, and produce high-temperature heat that is >20<sup> o</sup>C higher than the ambient temperature. Our work opens up a new avenue to harvest ambient heat, and demonstrate a feasible strategy to develop high-performance solar thermal battery.

Efficient Co-Harvesting of Solar Energy and Low-Grade Heat by Molecular Photoswitches for High Energy Density, Long-Term Stable Solar Thermal Battery

2019 ◽  
Author(s):  
Zhao-Yang Zhang ◽  
Tao LI
Keyword(s):  
Energy Density ◽  
Solar Energy ◽  
High Performance ◽  
High Energy ◽  
Solar Thermal ◽  
High Energy Density ◽  
Low Grade ◽  
Thermal Battery ◽  
Low Grade Heat

Solar energy and ambient heat are two inexhaustible energy sources for addressing the global challenge of energy and sustainability. Solar thermal battery based on molecular switches that can store solar energy and release it as heat has recently attracted great interest, but its development is severely limited by both low energy density and short storage stability. On the other hand, the efficient recovery and upgrading of low-grade heat, especially that of the ambient heat, has been a great challenge. Here we report that solar energy and ambient heat can be simultaneously harvested and stored, which is enabled by room-temperature photochemical crystal-to-liquid transitions of small-molecule photoswitches. The two forms of energy are released together to produce high-temperature heat during the reverse photochemical phase change. This strategy, combined with molecular design, provides high energy density of 320-370 J/g and long-term storage stability (half-life of about 3 months). On this basis, we fabricate high-performance, flexible film devices of solar thermal battery, which can be readily recharged at room temperature with good cycling ability, show fast rate of heat release, and produce high-temperature heat that is >20<sup> o</sup>C higher than the ambient temperature. Our work opens up a new avenue to harvest ambient heat, and demonstrate a feasible strategy to develop high-performance solar thermal battery.

scholarly journals Defect-induced B4C electrodes for high energy density supercapacitor devices

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Özge Balcı ◽  
Merve Buldu ◽  
Ameen Uddin Ammar ◽  
Kamil Kiraz ◽  
Mehmet Somer ◽  
...  
Keyword(s):  
Active Carbon ◽  
High Performance ◽  
Carbon Sources ◽  
High Energy ◽  
High Energy Density ◽  
Synthesis Conditions ◽  
High Energy Ball Mill ◽  
Energy Ball ◽  
G Ratio ◽  
Energy And Power Density

AbstractBoron carbide powders were synthesized by mechanically activated annealing process using anhydrous boron oxide (B2O3) and varying carbon (C) sources such as graphite and activated carbon: The precursors were mechanically activated for different times in a high energy ball mill and reacted in an induction furnace. According to the Raman analyses of the carbon sources, the I(D)/I(G) ratio increased from ~ 0.25 to ~ 0.99, as the carbon material changed from graphite to active carbon, indicating the highly defected and disordered structure of active carbon. Complementary advanced EPR analysis of defect centers in B4C revealed that the intrinsic defects play a major role in the electrochemical performance of the supercapacitor device once they have an electrode component made of bare B4C. Depending on the starting material and synthesis conditions the conductivity, energy, and power density, as well as capacity, can be controlled hence high-performance supercapacitor devices can be produced.

scholarly journals Recent Advances in the Synthesis of Polymer-Grafted Low-K and High-K Nanoparticles for Dielectric and Electronic Applications

Molecules ◽  
2021 ◽  
Vol 26 (10) ◽  
pp. 2942
Author(s):  
Bhausaheb V. Tawade ◽  
Ikeoluwa E. Apata ◽  
Nihar Pradhan ◽  
Alamgir Karim ◽  
Dharmaraj Raghavan
Keyword(s):  
Energy Density ◽  
Polymer Nanocomposites ◽  
High Performance ◽  
Breakdown Strength ◽  
Polymer Nanocomposite ◽  
High Energy ◽  
Polymer Chains ◽  
High Energy Density ◽  
Grafted Nanoparticles ◽  
Grafting From

The synthesis of polymer-grafted nanoparticles (PGNPs) or hairy nanoparticles (HNPs) by tethering of polymer chains to the surface of nanoparticles is an important technique to obtain nanostructured hybrid materials that have been widely used in the formulation of advanced polymer nanocomposites. Ceramic-based polymer nanocomposites integrate key attributes of polymer and ceramic nanomaterial to improve the dielectric properties such as breakdown strength, energy density and dielectric loss. This review describes the ”grafting from” and ”grafting to” approaches commonly adopted to graft polymer chains on NPs pertaining to nano-dielectrics. The article also covers various surface initiated controlled radical polymerization techniques, along with templated approaches for grafting of polymer chains onto SiO2, TiO2, BaTiO3, and Al2O3 nanomaterials. As a look towards applications, an outlook on high-performance polymer nanocomposite capacitors for the design of high energy density pulsed power thin-film capacitors is also presented.

Sulfur vacancies in Co9S8-x/N-doped graphene enhancing electrochemical kinetics to high-performance lithium sulfur batteries

2021 ◽  
Author(s):  
Haojie Li ◽  
Yihua Song ◽  
Kai Xi ◽  
Wei Wang ◽  
Sheng Liu ◽  
...  
Keyword(s):  
Cathode Materials ◽  
High Performance ◽  
Catalytic Conversion ◽  
High Energy ◽  
Electrochemical Kinetics ◽  
Lithium Sulfur Batteries ◽  
Doped Graphene ◽  
Sulfur Battery ◽  
Areal Capacity ◽  
Lithium Sulfur

A sufficient areal capacity is necessary for achieving high-energy lithium sulfur battery, which requires high enough sulfur loading in cathode materials. Therefore, kinetically fast catalytic conversion of polysulfide intermediates is...

scholarly journals Efficient Catalytic Conversion of Polysulfides by Biomimetic Design of “Branch-Leaf” Electrode for High-Energy Sodium–Sulfur Batteries

2021 ◽  
Vol 13 (1) ◽  
Author(s):  
Wenyan Du ◽  
Kangqi Shen ◽  
Yuruo Qi ◽  
Wei Gao ◽  
Mengli Tao ◽  
...  
Keyword(s):  
Active Sites ◽  
High Performance ◽  
Electrochemical Reaction ◽  
Molecular Layer ◽  
Specific Capacity ◽  
High Energy ◽  
Reduction Reaction ◽  
Biomimetic Design ◽  
Co Nanoparticles ◽  
Sodium Sulfur

AbstractRechargeable room temperature sodium–sulfur (RT Na–S) batteries are seriously limited by low sulfur utilization and sluggish electrochemical reaction activity of polysulfide intermediates. Herein, a 3D “branch-leaf” biomimetic design proposed for high performance Na–S batteries, where the leaves constructed from Co nanoparticles on carbon nanofibers (CNF) are fully to expose the active sites of Co. The CNF network acts as conductive “branches” to ensure adequate electron and electrolyte supply for the Co leaves. As an effective electrocatalytic battery system, the 3D “branch-leaf” conductive network with abundant active sites and voids can effectively trap polysulfides and provide plentiful electron/ions pathways for electrochemical reaction. DFT calculation reveals that the Co nanoparticles can induce the formation of a unique Co–S–Na molecular layer on the Co surface, which can enable a fast reduction reaction of the polysulfides. Therefore, the prepared “branch-leaf” CNF-L@Co/S electrode exhibits a high initial specific capacity of 1201 mAh g−1 at 0.1 C and superior rate performance.

A High-Performance Free-Standing Zn Anode for Flexible Zinc-Ion Batteries

Nanoscale ◽  
2021 ◽  
Author(s):  
Chenxi Gao ◽  
Jiawei Wang ◽  
Yuan Huang ◽  
Zixuan Li ◽  
Jiyan Zhang ◽  
...  
Keyword(s):  
Energy Density ◽  
High Performance ◽  
Low Cost ◽  
High Energy ◽  
Zinc Ion ◽  
High Energy Density ◽  
Free Standing ◽  
Energy Device ◽  
Zn Anode ◽  
Significant Attention

Zinc-ion batteries (ZIBs) have attracted significant attention owing to their high safety, high energy density, and low cost. ZIBs have been studied as a potential energy device for portable and...

Sign in / Sign up

Export Citation Format

Share Document