scholarly journals Early Hydration Heat of Calcium Sulfoaluminate Cement with Influences of Supplementary Cementitious Materials and Water to Binder Ratio

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 642
Author(s):  
Jun Zhang ◽  
Guoju Ke ◽  
Yuzhang Liu
Keyword(s):  
Critical Value ◽  
Cementitious Materials ◽  
Exothermic Peak ◽  
Hydration Heat ◽  
Supplementary Cementitious Materials ◽  
Calcium Sulfoaluminate Cement ◽  
Early Hydration ◽  
Calcium Sulfoaluminate ◽  
Granulated Blast Furnace Slag ◽  
Binder Ratio

Compared to ordinary Portland cement (OPC), calcium sulfoaluminate cement (CSA) displays very early-age strength and faster heat-releasing rate during hydration. In the present paper, the early hydration heat of CSA paste with influences of supplementary cementitious materials (SCMs) and water to cement (or binder) ratio (w/c) is systematically studied by measuring the heat-releasing rate using a calorimeter. Three traditional SCMs—silica fume (SF), fly ash (FA) and ground granulated blast furnace slag (SL)—were used in the study. A water to cement or binder ratio (w/c) between 0.19 and 0.73 was used in the mixtures. The results show that three exothermic peaks were presented during hydration—dissolution exothermic peak and two reaction exothermic peaks. With the w/c of 0.3, the first and second reaction peaks of the CSA paste are as high as 17.8 times and 4.1 times that of OPC paste, and the occurring time is much earlier than that of the OPC paste. The second reaction peak appears earlier, and the third reaction peak appears later in the pastes with addition of SF than in those without SF. Decreasing w/c can greatly reduce the two reaction peaks of the paste, and it looks that there is a critical value of w/c between 0.24 and 0.30. Above the critical value, the effect of w/c is minor, and below that the influence is obvious. An optimal use of SCMs in CSA pastes under different w/c can greatly decrease the heat releasing while maintaining the required strength.

scholarly journals Synthesis of a New Polycarboxylate at Room Temperature and Its Influence on the Properties of Cement Pastes with Different Supplementary Cementitious Materials

2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Shuncheng Xiang ◽  
Yingli Gao ◽  
Caijun Shi
Keyword(s):  
Room Temperature ◽  
Autogenous Shrinkage ◽  
Drying Shrinkage ◽  
Cementitious Materials ◽  
Heat Evolution ◽  
Hydration Heat ◽  
Supplementary Cementitious Materials ◽  
Cement Pastes ◽  
Binder Ratio ◽  
Water Binder Ratio

Three polycarboxylates with different comb structures (i.e., the same degree of polymerization in side chains but different main chains) were synthesized via radical polymerization reaction at room temperature. The effect of polycarboxylates on the surface tension and the flowability in cement pastes was determined. The best product was selected to study its effects on the hydration heat evolution, compressive strength, autogenous shrinkage, and drying shrinkage of cement pastes with different kinds and contents of supplementary cementitious materials. The results showed that with the increase of molar ratio between AA and TPEG to 6 : 1, we could synthesis the best product. When the water-binder ratio was 0.4, with the increase of polycarboxylates, the cement hydration heat evolution had been slowed down, and the more the dosage was, the more obvious the effect was. Adding supplementary cementitious materials to cement under the same experimental conditions also played a mitigation role in slowing down the hydration heat. When the water-binder ratio was 0.3, supplementary cementitious materials could increase the strength of cement by 24.5% in maximum; its autogenous shrinkage and drying shrinkage could be decreased, respectively, by 60.1% and 21.9% in the lowest.

Durability of Normal and Lightweight Aggregate Mortars with Different Supplementary Cementitious Materials

2021 ◽  
Vol 17 ◽  
pp. 271-281
Author(s):  
Efstratios Badogiannis ◽  
Eirhnh Makrinou ◽  
Marianna Fount
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Lightweight Aggregate ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Granulated Blast Furnace Slag ◽  
Binder Ratio ◽  
Pumice Sand ◽  
Water To Binder Ratio ◽  
Furnace Slag

A study on the durability parameters of normal and lightweight aggregate mortars, incorporated different supplementary cementitious materials (SCM) is presented. Mortars were prepared using limestone or pumice as aggregates and Metakaolin, Fly ash, Granulated Blast Furnace Slag and Silica Fume, as SCM, that they replaced cement, at 10 % by mass. Ten different mortars, having same water to binder ratio and aggregate to cement volumetric ratio, they were compared mainly in terms of durability. The use of pumice sand was proved to be effective not only to the density of the mortars as it was expected, but also in durability, fulfilling at the same time minimum strength requirements. The addition of the different SCM further enhanced the durability of the mortars, where Metakaolin was found to be the most effective one, especially against chloride’s ingress.

scholarly journals Self-Healing Products of Cement Pastes with Supplementary Cementitious Materials, Calcium Sulfoaluminate and Crystalline Admixtures

Materials ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7201
Author(s):  
Byoungsun Park ◽  
Young-Cheol Choi
Keyword(s):  
Phase Composition ◽  
Cementitious Materials ◽  
The Self ◽  
Ion Concentration ◽  
Supplementary Cementitious Materials ◽  
Self Healing ◽  
Cement Pastes ◽  
Main Compound ◽  
Calcium Sulfoaluminate ◽  
Granulated Blast Furnace Slag

The phase composition of self-healing products generated in cracks affects self-healing performance. This study investigated the self-healing products of cementitious materials using supplementary cementitious materials (SCMs), a calcium sulfoaluminate (CSA) expansion agent, and crystalline additives (CAs). Ground-granulated blast-furnace slag (GGBFS), fly ash (FA), and silica fume (SF) were used as SCMs, and anhydrite, Na2SO4, Na2CO3, and MgCO3 were used as crystalline additives (CAs). An artificial crack method was used to collect the self-healing products in the crack of the paste. The phase composition of the self-healing products was analyzed through X-ray diffraction (XRD)/Rietveld refinements and thermogravimetry/differential thermogravimetry (TG/DTG) analysis, and their morphology and ion concentration were examined through scanning electron microscopy with energy dispersive spectroscopy (SEM–EDS). From the results, the main compound of self-healing products was found to be calcite. GGBFS and FA decreased the content of portlandite, and the use of CAs led to the formation of alkali sulfate and alkali carbonate. The SEM–EDS analysis results showed that when GGBFS and FA were used, a large proportion of the self-healing products contained C-S-H and C-A-H, and the use of CSA led to the formation of monosulfate and ettringite.

Effect of ground granulated blast funrnace slag and fly ash on strength, permeability, and under-water abrasion of fine-grained concrete

2020 ◽  
Vol 71 (7) ◽  
pp. 775-788
Author(s):  
Quyet Truong Van ◽  
Sang Nguyen Thanh
Keyword(s):  
Fly Ash ◽  
Concrete Strength ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Chloride Permeability ◽  
Cement Replacement ◽  
Fine Grained ◽  
Granulated Blast Furnace Slag ◽  
Compressive Strength Test ◽  
Economic Ground

The utilisation of supplementary cementitious materials (SCMs) is widespread in the concrete industry because of the performance benefits and economic. Ground granulated blast furnace slag (GGBFS) and fly ash (FA) have been used as the SCMs in concrete for reducing the weight of cement and improving durability properties. In this study, GGBFS at different cement replacement ratios of 0%, 20%, 40% and 60% by weight were used in fine-grained concrete. The ternary binders containing GGBFS and FA at cement replacement ratio of 60% by weight have also evaluated. Flexural and compressive strength test, rapid chloride permeability test and under-water abrasion test were performed. Experimental results show that the increase in concrete strength with GGBFS contents from 20% to 40% but at a higher period of maturity (56 days and more). The chloride permeability the under-water abrasion reduced with the increasing cement replacement by GGBFS or a combination of GGBFS and FA

scholarly journals Effect of Flue Gas Desulfurization Gypsum on the Properties of Calcium Sulfoaluminate Cement Blended with Ground Granulated Blast Furnace Slag

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 382 ◽  
Author(s):  
Danying Gao ◽  
Zhenqing Zhang ◽  
Yang Meng ◽  
Jiyu Tang ◽  
Lin Yang
Keyword(s):  
Blast Furnace ◽  
Mechanical Strength ◽  
Flue Gas ◽  
Blast Furnace Slag ◽  
Setting Time ◽  
Flue Gas Desulfurization ◽  
Calcium Sulfoaluminate Cement ◽  
Calcium Sulfoaluminate ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

This work aims to investigate the effect of additional flue gas desulfurization gypsum (FGDG) on the properties of calcium sulfoaluminate cement (CSAC) blended with ground granulated blast furnace slag (GGBFS). The hydration rate, setting time, mechanical strength, pore structure and hydration products of the CSAC-GGBFS mixture containing FGDG were investigated systematically. The results show that the addition of FGDG promotes the hydration of the CSAC-GGBFS mixture and improves its mechanical strength; however, the FGDG content should not exceed 6%.

scholarly journals The Hydration, Mechanical, Autogenous Shrinkage, Durability, and Sustainability Properties of Cement–Limestone–Slag Ternary Composites

2021 ◽  
Vol 13 (4) ◽  
pp. 1881
Author(s):  
Mei-Yu Xuan ◽  
Yi Han ◽  
Xiao-Yong Wang
Keyword(s):  
Compressive Strength ◽  
Electrical Resistivity ◽  
Experimental Studies ◽  
Autogenous Shrinkage ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Hydration Heat ◽  
Granulated Blast Furnace Slag ◽  
Binder Ratio

This study examines the hydration–mechanical–autogenous shrinkage–durability–sustainability properties of ternary composites with limestone filler (LF) and ground-granulated blast furnace slag (BFS). Four mixtures were prepared with a water/binder ratio of 0.3 and different replacement ratios varying from 0 to 45%. Multiple experimental studies were performed at various ages. The experimental results are summarized as follows: (1) As the replacement levels increased, compressive strength and autogenous shrinkage (AS) decreased, and this relationship was linear. (2) As the replacement levels increased, cumulative hydration heat decreased. At the age of 3 and 7 days, there was a linear relationship between compressive strength and cumulative hydration heat. (3) Out of all mixtures, the ultrasonic pulse velocity (UPV) and electrical resistivity exhibited a rapid increase in the early stages and tended to slow down in the latter stages. There was a crossover of UPV among various specimens. In the later stages, the electrical resistivity of ternary composite specimens was higher than plain specimens. (4) X-ray diffraction (XRD) results showed that LF and BFS have a synergistic effect. (5) With increasing replacement ratios, the CO2 emissions per unit strength reduced, indicating the sustainability of ternary composites.

Research Progress on the Hydration of Portland Cement with Calcined Clay and Limestone

2021 ◽  
Vol 1036 ◽  
pp. 240-246
Author(s):  
Jin Tang ◽  
Su Hua Ma ◽  
Wei Feng Li ◽  
Hui Yang ◽  
Xiao Dong Shen
Keyword(s):  
Mechanical Properties ◽  
Portland Cement ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Research Progress ◽  
Hydration Reaction ◽  
Hydration Products ◽  
Early Hydration ◽  
Calcined Clay ◽  
Dense Microstructure

The use of calcined clay and limestone as supplementary cementitious materials, can have a certain influence on the hydration of Portland cement. This paper reviewed the influence of limestone and calcined clay and the mixture of limestone and calcined clay on the hydration of cement. Both limestone and calcined clay accelerate the hydration reaction in the early hydration age and enhance the properties of cement. Limestone reacts with C3A to form carboaluminate, which indirectly stabilized the presence of ettringite, while calcined clay consumed portlandite to form C-(A)-S-H gel, additional hydration products promote the densification of pore structure and increase the mechanical properties. The synergistic effect of calcined clay and limestone stabilize the existence of ettringite and stimulate the further formation of carboaluminate, as well as the C-(A)-S-H gel, contributed to a dense microstructure.

Sign in / Sign up

Export Citation Format

Share Document