scholarly journals Cesium Doping for Performance Improvement of Lead(II)-acetate-Based Perovskite Solar Cells

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 363
Author(s):  
Min-Seok Han ◽  
Zhihai Liu ◽  
Xuewen Liu ◽  
Jinho Yoon ◽  
Eun-Cheol Lee
Keyword(s):  
Solar Cells ◽  
Performance Improvement ◽  
Fill Factor ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Perovskite Materials ◽  
Lead Source

Lead(II)-acetate (Pb(Ac)2) is a promising lead source for the preparation of organolead trihalide perovskite materials, which avoids the use of inconvenient anti-solvent treatment. In this study, we investigated the effect of cesium doping on the performance of Pb(Ac)2-based perovskite solar cells (PSCs). We demonstrate that the quality of the CH3NH3PbI3 perovskite film was improved with increased crystallinity and reduced pinholes by doping the perovskite with 5 mol% cesium. As a result, the power conversion efficiency (PCE) of the PSCs was improved from 14.1% to 15.57% (on average), which was mainly induced by the significant enhancements in short-circuit current density and fill factor. A PCE of 18.02% was achieved for the champion device of cesium-doped Pb(Ac)2-based PSCs with negligible hysteresis and a stable output. Our results indicate that cesium doping is an effective approach for improving the performance of Pb(Ac)2-based PSCs.

scholarly journals The Influence of the Thickness of Compact TiO2 Electron Transport Layer on the Performance of Planar CH3NH3PbI3 Perovskite Solar Cells

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3295
Author(s):  
Andrzej Sławek ◽  
Zbigniew Starowicz ◽  
Marek Lipiński
Keyword(s):  
Solar Cells ◽  
Electron Transport ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Perovskite Solar Cells ◽  
Precursor Solution ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Transport Layer ◽  
Electron Transport Layer

In recent years, lead halide perovskites have attracted considerable attention from the scientific community due to their exceptional properties and fast-growing enhancement for solar energy harvesting efficiency. One of the fundamental aspects of the architecture of perovskite-based solar cells (PSCs) is the electron transport layer (ETL), which also acts as a barrier for holes. In this work, the influence of compact TiO2 ETL on the performance of planar heterojunction solar cells based on CH3NH3PbI3 perovskite was investigated. ETLs were deposited on fluorine-doped tin oxide (FTO) substrates from a titanium diisopropoxide bis(acetylacetonate) precursor solution using the spin-coating method with changing precursor concentration and centrifugation speed. It was found that the thickness and continuity of ETLs, investigated between 0 and 124 nm, strongly affect the photovoltaic performance of PSCs, in particular short-circuit current density (JSC). Optical and topographic properties of the compact TiO2 layers were investigated as well.

scholarly journals SCAPS Simulation on P3HT:Graphene Nanocomposites Based Bulk-Heterojunction Organic Solar Cells

2019 ◽  
Vol 9 (1) ◽  
pp. 28
Author(s):  
Nur Shakina Mohd Shariff ◽  
Puteri Sarah Mohamad Saad ◽  
Mohamad Rusop Mahmood
Keyword(s):  
Solar Cells ◽  
Organic Solar Cells ◽  
Fill Factor ◽  
Bulk Heterojunction ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Simulation Software ◽  
Capacitance Voltage

There has been an increasing interest towards organic solar cells after the discovery of conjugated polymer and bulk-heterojunction concept. Eventhough organic solar cells are less expensive than inorganic solar cells but the power conversion energy is still considered low. The main objective of this research is to investigate the effect of the P3HT’s thickness and concentration towards the efficiency of the P3HT:Graphene solar cells. A simulation software that is specialize for photovoltaic called SCAPS is used in this research to simulate the effect on the solar cells. The solar cell’s structure will be drawn inside the simulation and the parameters for each layers is inserted. The result such as the open circuit voltage (Voc), short circuit current density (Jsc), fill factor (FF), efficiency (η), capacitance-voltage (C-V) and capacitance-frequency (C-f) characteristic will be calculated by the software and all the results will be put into one graph.

scholarly journals The Performance Improvement of Using Hole Transport Layer with Lithium and Cobalt for Inverted Planar Perovskite Solar Cell

Coatings ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 354
Author(s):  
Shaoxi Wang ◽  
He Guan ◽  
Yue Yin ◽  
Chunfu Zhang
Keyword(s):  
Solar Cells ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Hole Mobility ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer ◽  
Planar Heterojunction

With the continuous development of solar cells, the perovskite solar cells (PSCs), whose hole transport layer plays a vital part in collection of photogenerated carriers, have been studied by many researchers. Interface transport layers are important for efficiency and stability enhancement. In this paper, we demonstrated that lithium (Li) and cobalt (Co) codoped in the novel inorganic hole transport layer named NiOx, which were deposited onto ITO substrates via solution methods at room temperature, can greatly enhance performance based on inverted structures of planar heterojunction PSCs. Compared to the pristine NiOx films, doping a certain amount of Li and Co can increase optical transparency, work function, electrical conductivity and hole mobility of NiOx film. Furthermore, experimental results certified that coating CH3NH3PbIxCl3−x perovskite films on Li and Co- NiOx electrode interlayer film can improve chemical stability and absorbing ability of sunlight than the pristine NiOx. Consequently, the power conversion efficiency (PCE) of PSCs has a great improvement from 14.1% to 18.7% when codoped with 10% Li and 5% Co in NiOx. Moreover, the short-circuit current density (Jsc) was increased from 20.09 mA/cm2 to 21.7 mA/cm2 and the fill factor (FF) was enhanced from 0.70 to 0.75 for the PSCs. The experiment results demonstrated that the Li and Co codoped NiOx can be a effective dopant to improve the performance of the PSCs.

Efficient light harvesting with a nanostructured organic electron-transporting layer in perovskite solar cells

Nanoscale ◽  
2019 ◽  
Vol 11 (19) ◽  
pp. 9281-9286 ◽  
Author(s):  
Li Wan ◽  
Wenxiao Zhang ◽  
Yulei Wu ◽  
Xiaodong Li ◽  
Changjian Song ◽  
...  
Keyword(s):  
Solar Cells ◽  
Light Harvesting ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Organic Electron ◽  
Electron Transporting Layer ◽  
Harvesting Efficiency ◽  
Light Harvesting Efficiency

A nanostructured electron-transporting layer based on PFPDI was introduced into inverted perovskite solar cells. The light-harvesting efficiency and the short-circuit current density were greatly improved.

Iodide management in formamidinium-lead-halide–based perovskite layers for efficient solar cells

Science ◽  
2017 ◽  
Vol 356 (6345) ◽  
pp. 1376-1379 ◽  
Author(s):  
Woon Seok Yang ◽  
Byung-Wook Park ◽  
Eui Hyuk Jung ◽  
Nam Joong Jeon ◽  
Young Chan Kim ◽  
...  
Keyword(s):  
Solar Cells ◽  
High Performance ◽  
Deep Level ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Small Cells ◽  
Iodide Ions

The formation of a dense and uniform thin layer on the substrates is crucial for the fabrication of high-performance perovskite solar cells (PSCs) containing formamidinium with multiple cations and mixed halide anions. The concentration of defect states, which reduce a cell’s performance by decreasing the open-circuit voltage and short-circuit current density, needs to be as low as possible. We show that the introduction of additional iodide ions into the organic cation solution, which are used to form the perovskite layers through an intramolecular exchanging process, decreases the concentration of deep-level defects. The defect-engineered thin perovskite layers enable the fabrication of PSCs with a certified power conversion efficiency of 22.1% in small cells and 19.7% in 1-square-centimeter cells.

scholarly journals Optical Property and Photoelectrical Performance of a Low-bandgap Conducting Polymer Incorporated with Quantum Dots Used for Organic Solar Cells

2015 ◽  
Vol 25 (2) ◽  
pp. 139
Author(s):  
Tran Thi Thao ◽  
Vu Thi Hai ◽  
Nguyen Nang Dinh ◽  
Le Dinh Trong
Keyword(s):  
Quantum Dots ◽  
Solar Cells ◽  
Organic Solar Cells ◽  
Fill Factor ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Low Bandgap ◽  
A Value

By using spin-coating technique, a low bandgap conjugated polymer, poly[2,6-(4,4-bis-(2-ethylhexyl)-4H-cyclopen-ta[2,1-b;3,4-b′]dithiophene)-alt-4,7-(2,1,3-benzothiadiazole)] (PCPDTBT)  and its composite thin films have been prepared. The optical absorption and photoconductive properties with over a wide spectral range, from 350 to 950  nm, were characterized. The obtained results showed that PCPDTBT:10 wt% CdSe  composite is the most suitable for efficient light-harvesting in polymer-based photovoltaic cells. The photoelectrical conversion efficiency (PCE) of the device with  a multilayer structure of ITO/PEDOT/ PCPDTBT:CdSe /LiF/Al  reached a value as large as 1.34% with an open-circuit voltage (Voc) = 0.57 V, a short-circuit current density (Jsc) = 4.29 mA/cm2, and a fill factor (FF) = 0.27. This suggests a useful application in further fabrication of quantum dots/polymers based solar cells.

scholarly journals Fabrication and Characterization of CH3NH3PbI3 Perovskite Solar Cells Added with Polysilanes

2018 ◽  
Vol 2018 ◽  
pp. 1-7 ◽  
Author(s):  
Takeo Oku ◽  
Junya Nomura ◽  
Atsushi Suzuki ◽  
Hiroki Tanaka ◽  
Sakiko Fukunishi ◽  
...  
Keyword(s):  
Solar Cells ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Interfacial Structure ◽  
Perovskite Layer ◽  
Photovoltaic Properties ◽  
Coating Method

Effects of polysilane additions on CH3NH3PbI3 perovskite solar cells were investigated. Photovoltaic cells were fabricated by a spin-coating method using perovskite precursor solutions with polymethyl phenylsilane, polyphenylsilane, or decaphenyl cyclopentasilane (DPPS), and the microstructures were examined by X-ray diffraction and optical microscopy. Open-circuit voltages were increased by introducing these polysilanes, and short-circuit current density was increased by the DPPS addition, which resulted in the improvement of the photoconversion efficiencies to 10.46%. The incident photon-to-current conversion efficiencies were also increased in the range of 400~750 nm. Microstructure analysis indicated the formation of a dense interfacial structure by grain growth and increase of surface coverage of the perovskite layer with DPPS, and the formation of PbI2 was suppressed, leading to the improvement of photovoltaic properties.

Simultaneous Enhancement of Open-Circuit Voltage, Short-Circuit Current Density, and Fill Factor in Polymer Solar Cells

2011 ◽  
Vol 23 (40) ◽  
pp. 4636-4643 ◽  
Author(s):  
Zhicai He ◽  
Chengmei Zhong ◽  
Xun Huang ◽  
Wai-Yeung Wong ◽  
Hongbin Wu ◽  
...  
Keyword(s):  
Solar Cells ◽  
Current Density ◽  
Fill Factor ◽  
Open Circuit Voltage ◽  
Polymer Solar Cells ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit

A Comparative Study between Silicon Germanium and Germanium Solar Cells by Numerical Simulation

2015 ◽  
Vol 761 ◽  
pp. 341-346 ◽  
Author(s):  
Ahmad Aizan Zulkefle ◽  
Maslan Zainon ◽  
Zaihasraf Zakaria ◽  
Mohd Ariff Mat Hanafiah ◽  
Nurul Huda Abdul Razak ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Silicon Germanium ◽  
Fill Factor ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Cell Modeling ◽  
Modeling Software

This paper presents the performance between silicon germanium (SiGe) and crystalline germanium (Ge) solar cells in terms of their simulated open circuit voltage, short circuit current density, fill factor and efficiency. The PC1D solar cell modeling software has been used to simulate and analyze the performance for both solar cells, and the total thickness is limited to 1μm of both SiGe and Ge solar cells. The Si0.1Ge0.9 thickness is varied from 10nm to 100nm to examine the effect of Si0.1Ge0.9 thickness on SiGe solar cell. The result of simulation exhibits the SiGe solar cell give a better performance compared to Ge solar cell. The efficiency of 9.74% (VOC = 0.48V, JSC = 27.86mA/cm2, FF =0.73) is achieved with Si0.1Ge0.9 layer of 0.1μm in thickness whilst 2.73% (VOC = 0.20V, JSC = 27.31mA/cm2, FF =0.50) efficiency is obtained from Ge solar cell.

Bifacial microcrystalline silicon solar cells with improved performance due to μc-SiOx:H doped layers

2014 ◽  
Vol 92 (7/8) ◽  
pp. 913-916 ◽  
Author(s):  
V. Smirnov ◽  
A. Lambertz ◽  
F. Finger
Keyword(s):  
Solar Cells ◽  
Silicon Oxide ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Microcrystalline Silicon ◽  
Improved Performance ◽  
Conversion Efficiencies ◽  
Insight Into

We present the development and application of n-type hydrogenated microcrystalline silicon oxide (μc-SiOx:H) in semitransparent bifacial microcrystalline silicon (μc-Si:H) solar cells. Semitransparent bifacial solar cells are of interest for a number of technical applications like building integration or concentrator devices, but also can offer new insight into solar cell properties due to the possibility to illuminate the cell from both sides. Appropriately selected μc-SiOx:H n-layers with low refractive index and high optical band gap allow the reduction of the reflection of the cells and improve short circuit current density (JSC) and conversion efficiencies. The quality of n-type μc-SiOx:H window layers is demonstrated in solar cells with highly reflective ZnO/Ag contacts. High JSC values of 24.8 mA/cm2 and efficiencies of 9.5% are obtained for 1 μm thick solar cells.

Sign in / Sign up

Export Citation Format

Share Document