scholarly journals Monotonic and Cyclic Loading/Unloading Tensile Behavior of 3D Needle-Punched C/SiC Ceramic-Matrix Composites

Materials ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 57
Author(s):  
Yufeng Liu ◽  
Longbiao Li ◽  
Zhongwei Zhang ◽  
Xiang Xiong
Keyword(s):  
Tensile Strength ◽  
Cyclic Loading ◽  
Residual Strain ◽  
Fracture Strain ◽  
Hysteresis Loops ◽  
Tensile Behavior ◽  
Tangent Modulus ◽  
Peak Strain ◽  
Fiber Volume ◽  
Initial Tangent Modulus

In this paper, monotonic and cyclic loading/unloading tensile behavior of four different 3D needle-punched C/SiC composites are investigated. Under tensile loading, multiple micro parameters of tensile tangent modulus, tensile strength, and fracture strain are used to characterize tensile damage and fracture behavior. Under cyclic loading/unloading, multiple damage micro parameters of unloading residual strain, tensile peak strain, hysteresis loops width, hysteresis loops area, unloading and reloading inverse tangent modulus (ITM) are used to describe the tensile damage evolution. After tensile fracture, fracture surfaces were observed under a scanning electron microscope (SEM). Damage of matrix cracking, interface debonding, fibers fracture and pullout in different plies is observed. Relationships between composite tensile mechanical behavior, damage parameters, and micro damage mechanisms are established. When the fiber volume fraction along the loading direction increases, the composite initial tangent modulus, tensile strength and fracture strain increase, and the unloading residual strain, peak strain, hysteresis width and hysteresis area decrease. For Types 1–4 3D needle-punched C/SiC composite, the fiber volume lies in the range of 25.6–32.8%, the composite initial tangent modulus was in the range of 161.4–220.4 GPa, the composite tensile strength was in the range of 64.4–112.3 MPa, and the composite fracture strain was in the range of 0.16–0.25%.

scholarly journals Effect of In Situ Grown BNNTs and Preparation Temperature on Mechanical Behavior of SiC/SiC Minicomposites

2021 ◽  
Author(s):  
Shenwei Xu ◽  
Huilong Pi ◽  
Pengfei Wu ◽  
Yuan Shi ◽  
Haitang Yang ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Elastic Modulus ◽  
Mechanical Behavior ◽  
Fracture Strain ◽  
Thermal Structure ◽  
Annealing Process ◽  
Tangent Modulus ◽  
Tensile Fracture ◽  
Preparation Temperature

Abstract In this paper, effect of in situ grown boron nitride nanotubes (BNNTs) and preparation temperature on mechanical behavior of PIP (Precursor Infiltration and Pyrolysis) SiC/SiC minicomposites under monotonic and compliance tensile is investigated. In situ BNNTs are grown on the surface of SiC fibers using ball milling – annealing process. Composite elastic modulus, tensile strength, fracture strain, tangent modulus, and loading/unloading inverse tangent modulus (ITM) are obtained and adopted to characterize the mechanical properties of the composites. Microstructures of in situ grown BNNTs and tensile fracture surfaces are observed under scanning electronic microscopic (SEM). For SiC/SiC minicomposites with BNNTs, the elastic modulus, tensile strength, and fracture strain are all lower than those of SiC/SiC minicomposites without BNNTs, mainly due to high preparation temperature and the oxidation of the PyC interphase during the annealing process. Tensile stress-strain curves of SiC/SiC minicomposites with and without BNNTs are predicted using the developed micromechanical constitutive model. The predicted results agreed with experimental data. This work will provide guidance for predicting the service life of SiCf/SiC composite materials and may enable these materials to become a backbone for thermal structure systems in aerospace applications.

Comparison of prior exposure tensile damage and fracture of two-dimensional C/SiC and SiC/SiC fiber-reinforced ceramic-matrix composites

2020 ◽  
Vol 90 (23-24) ◽  
pp. 2782-2794
Author(s):  
Longbiao Li
Keyword(s):  
Tensile Strength ◽  
Fracture Strain ◽  
Prior Exposure ◽  
Interface Debonding ◽  
Fiber Volume ◽  
Damage And Fracture ◽  
Exposure Temperature ◽  
Fiber Characteristic ◽  
Sic Composites ◽  
Tensile Damage

In this paper, a micromechanical constitutive model for prior exposure tensile damage and fracture of fiber-reinforced ceramic-matrix composites is developed considering the multiple damage mechanisms of matrix multicracking, interface debonding and oxidation, and fiber fracture. The relationships between prior exposure temperature, duration time, interface debonding fraction, broken fiber fraction, tensile strength, and fracture strain of C/SiC and SiC/SiC composites are established. The experimental prior exposure tensile damage evolution and final fracture of two-dimensional (2D) C/SiC and SiC/SiC composites are predicted for different temperatures and duration times. The comparison analysis of prior exposure composite tensile strength, fracture strain, interface debonding fraction, and broken fiber fraction between 2D C/SiC and SiC/SiC composites is investigated. The effects of constituent properties and temperature on prior exposure tensile damage and fracture of 2D C/SiC and SiC/SiC composites are discussed. For 2D C/SiC and SiC/SiC composites under prior exposure at 1300℃, the fracture strain decreased with fiber volume, interface shear stress, and prior exposure temperature, and increased with fiber characteristic strength; the tensile strength increased with fiber volume and fiber characteristic strength, and decreased with prior exposure temperature; the interface debonding fraction decreased with fiber volume, and increased with prior exposure temperature; and the fiber broken fraction decreased with fiber volume and fiber characteristic strength, and increased with prior exposure temperature.

Prediction of internal geometry and tensile behavior of 3D woven solid structures by mathematical coding

2021 ◽  
pp. 152808372110013
Author(s):  
Vivek R Jayan ◽  
Lekhani Tripathi ◽  
Promoda Kumar Behera ◽  
Michal Petru ◽  
BK Behera
Keyword(s):  
Volume Fraction ◽  
Three Dimensional ◽  
Areal Density ◽  
Woven Fabrics ◽  
Tensile Behavior ◽  
Geometrical Parameters ◽  
Fiber Volume ◽  
Acceptable Error ◽  
Internal Geometry ◽  
Unit Cells

The internal geometry of composite material is one of the most important factors that influence its performance and service life. A new approach is proposed for the prediction of internal geometry and tensile behavior of the 3 D (three dimensional) woven fabrics by creating the unit cell using mathematical coding. In many technical applications, textile materials are subjected to rates of loading or straining that may be much greater in magnitude than the regular household applications of these materials. The main aim of this study is to provide a generalized method for all the structures. By mathematical coding, unit cells of 3 D woven orthogonal, warp interlock and angle interlock structures have been created. The study then focuses on developing code to analyze the geometrical parameters of the fabric like fabric thickness, areal density, and fiber volume fraction. Then, the tensile behavior of the coded 3 D structures is studied in Ansys platform and the results are compared with experimental values for authentication of geometrical parameters as well as for tensile behavior. The results show that the mathematical coding approach is a more efficient modeling technique with an acceptable error percentage.

Effect of Friction Stir Welding Parameters on Thermal and Tensile Behavior of Aluminum Weldments Using Double Shoulder Tools

2012 ◽  
Vol 622-623 ◽  
pp. 323-329
Author(s):  
Ebtisam F. Abdel-Gwad ◽  
A. Shahenda ◽  
S. Soher
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Welding Process ◽  
Tensile Behavior ◽  
Frictional Heat ◽  
Welding Parameters ◽  
Friction Stir ◽  
Aluminum Base ◽  
Tool Pin ◽  
Strength And Ductility

Friction stir welding (FSW) process is a solid state welding process in which the material being welded does not melt or recast. This process uses a non-consumable tool to generate frictional heat in the abutting surfaces. The welding parameters and tool pin profile play major roles in deciding the weld quality. In this investigation, an attempt has been made to understand effects of process parameters include rotation speeds, welding speeds, and pin diameters on al.uminum weldment using double shoulder tools. Thermal and tensile behavior responses were examined. In this direction temperatures distribution across the friction stir aluminum weldment were measured, besides tensile strength and ductility were recorded and evaluated compared with both single shoulder and aluminum base metal.

Tensile Behavior after Oxidative Aging of Gum and Black-Filled Vulcanizates of SBR and NR

1999 ◽  
Vol 72 (4) ◽  
pp. 721-730 ◽  
Author(s):  
G. R. Hamed ◽  
J. Zhao
Keyword(s):  
Tensile Strength ◽  
Natural Rubber ◽  
Tensile Behavior ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Oxidative Aging ◽  
Prolonged Aging ◽  
Aging Period ◽  
Early Aging ◽  
Styrene Butadiene

Abstract Typical sulfur-cured vulcanizates of styrene-butadiene rubber (SBR) and natural rubber (NR) were prepared, and subjected to air-oven aging at 100 °C. Gum specimens exhibited an initial aging period in which stiffness was unchanged, while tensile strength and strain-to-break were significantly reduced. In contrast, black-filled vulcanizates stiffened during early aging. After intermediate aging times, NR specimens softened, while SBR stiffened. With prolonged aging, all compositions became hard and inextensible.

Performance of Bamboo Fiber Reinforced Composites: Mechanical Properties

2021 ◽  
Vol 879 ◽  
pp. 284-293
Author(s):  
Norliana Bakar ◽  
Siew Choo Chin
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Vinyl Ester ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Bamboo Fiber ◽  
Synthetic Fiber ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Volume Fractions

Fiber Reinforced Polymer (FRP) made from synthetic fiber had been widely used for strengthening of reinforced concrete (RC) structures in the past decades. Due to its high cost, detrimental to the environment and human health, natural fiber composites becoming the current alternatives towards a green and environmental friendly material. This paper presents an investigation on the mechanical properties of bamboo fiber reinforced composite (BFRC) with different types of resins. The BFRC specimens were prepared by hand lay-up method using epoxy and vinyl-ester resins. Bamboo fiber volume fractions, 30%, 35%, 40%, 45% and 50% was experimentally investigated by conducting tensile and flexural test, respectively. Results showed that the tensile and flexural strength of bamboo fiber reinforced epoxy composite (BFREC) was 63.2% greater than the bamboo fiber reinforced vinyl-ester composite (BFRVC). It was found that 45% of bamboo fiber volume fraction on BFREC exhibited the highest tensile strength compared to other BFRECs. Meanwhile, 40% bamboo fiber volume fraction of BFRVC showed the highest tensile strength between bamboo fiber volume fractions for BFRC using vinyl-ester resin. Studies showed that epoxy-based BFRC exhibited excellent results compared to the vinyl-ester-based composite. Further studies are required on using BFRC epoxy-based composite in various structural applications and strengthening purposes.

scholarly journals A numerical and experimental study on the tensile behavior of plasma shocked granite under dynamic loading

2017 ◽  
Vol 50 (2) ◽  
pp. 41-62
Author(s):  
Ahmad Mardoukhi ◽  
Timo Saksala ◽  
Mikko Hokka ◽  
Veli-Tapani Kuokkala
Keyword(s):  
Experimental Study ◽  
Tensile Strength ◽  
Mechanical Behavior ◽  
Thermal Shock ◽  
Dynamic Loading ◽  
Split Hopkinson Pressure Bar ◽  
Tensile Behavior ◽  
Brazilian Disc ◽  
Brazilian Disc Test ◽  
Plasma Shock

This paper presents a numerical and experimental study on the mechanical behavior of plasma shocked rock. The dynamic tensile behavior of plasma shock treated Balmoral Red granite was studied under dynamic loading using the Brazilian disc test and the Split Hopkinson Pressure Bar device. Different heat shocks were produced on the Brazilian disc samples by moving the plasma gun over the sample at different speeds. Microscopy clearly showed that as the duration of the thermal shock increases, the number of the surface cracks and their complexity increases (quantified here as the fractal dimension of the crack patterns) and the area of the damaged surface grows larger as well. At the highest thermal shock duration of 0.80 seconds the tensile strength of the Brazilian disc sample drops by approximately 20%. In the numerical simulations of the dynamic Brazilian disc test, this decrease in tensile strength was reproduced by modeling the plasma shock induced damage using the embedded discontinuity finite element method. The damage caused by the plasma shock was modeled by two methods, namely by pre-embedded discontinuity populations with zero strength and by assuming that the rock strength is lowered and conform to the Weibull distribution. This paper presents a quantitative assessment of the effects of the heat shock, the surface microstructure and mechanical behavior of the studied rock, and a promising numerical model to account for the pre-existing crack distributions in a rock material.

scholarly journals Tensile Mechanical Properties and Failure Modes of a Basalt Fiber/Epoxy Resin Composite Material

2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
Jingjing He ◽  
Junping Shi ◽  
Xiaoshan Cao ◽  
Yifeng Hu
Keyword(s):  
Tensile Strength ◽  
Composite Material ◽  
Fiber Volume Fraction ◽  
Failure Modes ◽  
Volume Fraction ◽  
Basalt Fiber ◽  
Orientation Angle ◽  
Fiber Volume ◽  
Fiber Clustering ◽  
Fiber Orientation Angle

Uniaxial tensile tests of basalt fiber/epoxy (BF/EP) composite material with four different fiber orientations were conducted under four different fiber volume fractions, and the variations of BF/EP composite material failure modes and tensile mechanical properties were analyzed. The results show that when the fiber volume fraction is constant, the tensile strength, elastic modulus, and limiting strain of BF/EP composite material all decrease with increasing fiber orientation angle. When the fiber orientation angle is constant, the tensile strength, elastic modulus, and limiting strain of BF/EP composite material all increase with increasing fiber volume fraction. A certain degree of fiber clustering appears in the epoxy resin when the basalt fiber volume fraction is >1.2%. The fiber equidistribution coefficient and clustering fiber content were used to characterize the basalt fiber clustering effect. With the increase of fiber volume fraction, the clustering fiber content gradually increased, but the fiber equidistribution coefficient decreased. Meanwhile, based on Tsai theory, a geometric model and a tensile mechanical model of the clustering fiber are established. By considering the fiber clustering effect, the BF/EP composite material tensile strength is calculated, and the calculated values are close to the experimental results.

Intrinsically Stretchable Naphthalenediimide–Bithiophene Conjugated Statistical Terpolymers Using Branched Conjugation Break Spacers for Field–Effect Transistors

2021 ◽  
Author(s):  
Yan-Cheng Lin ◽  
Megumi Matsuda ◽  
Kei-ichiro Sato ◽  
Chun-Kai Chen ◽  
Wei-Chen Yang ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Conjugated Polymers ◽  
Field Effect ◽  
Fracture Strain ◽  
Field Effect Transistors

The development of conjugated polymers through the statistical terpolymerization of conjugation break spacers (CBSs) has received great attention because of their synergistic potential in enhancing fracture strain and tensile strength....

Sign in / Sign up

Export Citation Format

Share Document