scholarly journals Joining Alumina to Titanium Alloys Using Ag-Cu Sputter-Coated Ti Brazing Filler

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 4802
Author(s):  
Omid Emadinia ◽  
Aníbal Guedes ◽  
Carlos José Tavares ◽  
Sónia Simões
Keyword(s):  
Microstructural Characterization ◽  
Interface Bonding ◽  
Soft Or ◽  
Tial Alloys ◽  
X Ray ◽  
Distribution Maps ◽  
Ti Oxides ◽  
Ti Alloys ◽  
Central Regions

The joining of alumina (Al2O3) to γ-TiAl and Ti6Al4V alloys, using Ag-Cu sputter-coated Ti brazing filler foil, was investigated. Brazing experiments were performed at 980 °C for 30 min in vacuum. The microstructure and chemical composition of the brazed interfaces were analyzed by scanning electron microscopy and by energy dispersive X-ray spectroscopy, respectively. A microstructural characterization of joints revealed that sound multilayered interfaces were produced using this novel brazing filler. Both interfaces are composed mainly of α-Ti, along with Ti2(Ag,Cu) and TiAg intermetallics. In the case of the brazing of γ-TiAl alloys, α2-Ti3Al and γ-TiAl intermetallics are also detected at the interface. Bonding to Al2O3 is promoted by the formation of a quite hard Ti-rich layer, which may reach a hardness up to 1872 HV 0.01 and is possibly composed of a mixture of α-Ti and Ti oxides. Hardness distribution maps indicate that no segregation of either soft or brittle phases occurs at the central regions of the interfaces or near the base Ti alloys. In addition, a smooth hardness transition was established between the interface of Al2O3 to either γ-TiAl or Ti6Al4V alloys.

scholarly journals Diffusion Bonding of Ti6Al4V to Al2O3 Using Ni/Ti Reactive Multilayers

Metals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 655
Author(s):  
Marcionilo Silva ◽  
Ana S. Ramos ◽  
M. Teresa Vieira ◽  
Sónia Simões
Keyword(s):  
Thin Films ◽  
Diffusion Bonding ◽  
Mechanical Characterization ◽  
Base Material ◽  
Microstructural Characterization ◽  
Multilayer Thin Films ◽  
X Ray ◽  
Distribution Maps ◽  
Base Materials

This paper aims to investigate the diffusion bonding of Ti6Al4V to Al2O3. The potential of the use of reactive nanolayered thin films will also be investigated. For this purpose, Ni/Ti multilayer thin films with a 50 nm modulation period were deposited by magnetron sputtering onto the base materials. Diffusion bonding experiments were performed at 800 °C, under 50 MPa and a dwell time of 60 min, with and without interlayers. Microstructural characterization of the interface was conducted through scanning electron microscopy (SEM) with energy-dispersive X-ray spectroscopy (EDS). The joints experiments without interlayer were unsuccessful. The interface is characterized by the presence of a crack close to the Al2O3 base material. The results revealed that the Ni/Ti reactive multilayers improved the diffusion bonding process, allowing for sound joints to be obtained at 800 °C for 60 min. The interface produced is characterized by a thin thickness and is mainly composed of NiTi and NiTi2 reaction layers. Mechanical characterization of the joint was assessed by hardness and reduced Young’s modulus distribution maps that enhance the different phases composing the interface. The hardness maps showed that the interface exhibits a hardness distribution similar to the Al2O3, which can be advantageous to the mechanical behavior of the joints.

Influence of the Residue of Casting by Lost Wax in the Modulus of Elasticity and Porosity of Concretes

2014 ◽  
Vol 805 ◽  
pp. 343-349
Author(s):  
Carine F. Machado ◽  
Weber G. Moravia
Keyword(s):  
Construction Industry ◽  
Modulus Of Elasticity ◽  
Chemical Characterization ◽  
Microstructural Characterization ◽  
Cement Matrix ◽  
X Ray Diffraction ◽  
X Ray ◽  
Hardened State ◽  
Material Powder

This work evaluated the influence of additions of the ceramic shell residue (CSR), from the industries of Lost Wax Casting, in the modulus of elasticity and porosity of concrete. The CSR was ground and underwent a physical, chemical, and microstructural characterization. It was also analyzed, the environmental risk of the residue. In the physical characterization of the residue were analyzed, the surface area, and particle size distribution. In chemical characterization, the material powder was subjected to testing of X-ray fluorescence (XRF). Microstructural characterization was performed by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The residue was utilized like addition by substitution of cement in concrete in the percentages of 10% and 15% by weight of Portland cement. It was evaluated properties of concrete in the fresh and hardened state, such as compressive strength, modulus of elasticity, absorption of water by total immersion and by capillarity. The results showed that the residue can be used in cement matrix and improve some properties of concrete. Thus, the CSR may contribute to improved sustainability and benefit the construction industry.

Microstructural Characterization of α2 + γ Titanium Aluminides

1997 ◽  
Vol 3 (S2) ◽  
pp. 701-702
Author(s):  
D. J. Larson ◽  
M. K. Miller
Keyword(s):  
Titanium Aluminides ◽  
Base Alloy ◽  
Significant Proportion ◽  
Weight Ratio ◽  
High Strength ◽  
Microstructural Characterization ◽  
Two Phase ◽  
Tial Alloys ◽  
Boron Doped

Two-phase α2+γ TiAl alloys with microalloying additions, Fig. 1, are of interest due to the high strength-to-weight ratio they can provide in automotive and aircraft applications. In boron-doped α2+γTiAl containing Cr, Nb, and W, the B levels were found to be significantly depleted below the nominal alloy content in both the α2 andγ phases. The boron solubilities in the γ and α2 phases were 0.011 ± 0.005 at. % B and 0.003 ± 0.005 at. % B, respectively in Ti-47% Al-2% Cr-1.8% Nb-0.2% W-0.15 % B that was aged for 2 h at 900°C (base alloy). The majority of the B was in a variety of borides including TiB, TiB2 and a Cr-enriched (Ti,Cr)2B precipitate. With the exception of the smaller (< 50 nm thick) Cr-enriched (Ti,Cr)2B precipitates, Fig. 2, most of the borides were larger than ∼100 nm. A significant proportion of the microalloying additions is in these borides, Table 1.

Heat Treatment and Oxidation Characteristics of Nb-20Mo-15Si-5B-20(Cr,Ti) Alloys from 700 to 1400°C

2010 ◽  
Vol 638-642 ◽  
pp. 2351-2356 ◽  
Author(s):  
Sylvia Natividad ◽  
Arianna Acosta ◽  
Krista Amato ◽  
Julieta Ventura ◽  
Benedict Protillo ◽  
...  
Keyword(s):  
Unit Area ◽  
Annealing Treatment ◽  
Microstructural Characterization ◽  
Solution Phase ◽  
Solid Solution Phase ◽  
Ti Alloy ◽  
X Ray ◽  
Ti Alloys ◽  
Higher Temperature ◽  
Oxidation In Air

Nb-20Mo-15Si-5B-20(Cr,Ti) alloys have been subjected to annealing treatment for 2 hours in a range of temperatures from 700 to 1400oC and quenched in water to perform the microstructural characterization for these two new alloys. As cast structure consists of a solid solution phase, , and silicides (Nb5Si3) in both alloys but Cr alloy also contains NbCr2 and Nb3Si phases. Heating to higher temperature introduces Ti silicides in the microstructure for Ti alloy. The oxidation in air has been conducted on these alloys in the same temperature range for 24 hours. Weight gain per unit area as a function of temperature provides the oxidation curves while characterization techniques using SEM, EDS on SEM, x-ray mapping, and XRD has yielded the analyses of the oxide scale. The scale consists of various oxides of Nb, Mo, Cr, Si, and Ti. Cr alloy appears to offer higher oxidation resistance in the selected range of oxidation temperatures.

Microstructural characterization of biobased carbon foam by means of X-ray microtomography and compared to conventional techniques

RSC Advances ◽  
2016 ◽  
Vol 6 (98) ◽  
pp. 96057-96064 ◽  
Author(s):  
Juliette Merle ◽  
Pascale Sénéchal ◽  
Fabrice Guerton ◽  
Peter Moonen ◽  
Pierre Trinsoutrot ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Mercury Intrusion Porosimetry ◽  
Microstructural Characterization ◽  
Carbon Foam ◽  
X Ray ◽  
Mercury Intrusion ◽  
Scanning Electron

The objective of this work is to compare three techniques for characterizing the morphology of porous bio-based carbon foam, namely mercury intrusion porosimetry, scanning electron microscopy and X-ray microtomography.

Microstructural Characterization of Polyanhydride Blends for Controlled Drug Delivery

2000 ◽  
Vol 662 ◽  
Author(s):  
Elizabeth E. Shen ◽  
Hsin-Lung Chen ◽  
Balaji Narasimhan
Keyword(s):  
Drug Delivery ◽  
Microstructural Characterization ◽  
Peak Shift ◽  
Crystalline Morphology ◽  
X Ray ◽  
Force Microscopy ◽  
X Ray Scattering ◽  
Atomic Force ◽  
Drug Delivery Devices

AbstractThis research examines the microstructure of polyanhydride blends for use in drug delivery devices. Atomic force microscopy (AFM) and small-angle X-ray scattering (SAXS) studies were performed on the homopolymers and blends of the polyanhydrides poly(1,6-carboxyphenoxy hexane) (CPH) and poly(sebacic anhydride) (SA). AFM of the CPH/SA blends 20:80, 50:50, and 80:20 showed distinct patterns indicating spinodal decomposition and phase separation on the micron-scale. Because it has been shown that incorporated drugs will thermodynamically partition into phase-separated domains depending on their hydrophobicity, polyanhydride blends will be able to encapsulate larger bioactive compounds including nucleotides, proteins, and vaccines. Preliminary SAXS studies of the CPH/SA blend systems provide information on the crystalline morphology of the polymer. A peak shift to a lower q from poly(SA) to the blends indicates that the poly(CPH) is incorporated into and causes swelling of the interlamellar amorphous regions of poly(SA).

Sign in / Sign up

Export Citation Format

Share Document